Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Comparison on Condensation Heat Transfer Performance of R407C Outside Petal-Shaped Finned Tube With Low Finned Tube

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Effect of Fin Structure on the Condensation of R-134a, R-1234ze(E), and R-1233zd(E) Outside the Titanium Tubes

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Comparison Of R410a Condensation Heat Transfer Performance On Three Horizontal Tubes

Condensation Heat Transfer Experiments of R410A and R32 in Horizontal Smooth and Enhanced Tubes

Film-wise Condensation of R-134a, R-1234ze(E) and R-1233zd(E) Outside the Finned Tubes with Different Fin Thickness

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth, Herringbone and Enhanced Surface EHT Tubes

Condensation Heat Transfer of R410A on Outside of Horizontal Smooth and Three-Dimensional Enhanced Tubes

R410A Flow Condensation Inside Two Dimensional Micro-Fin Tubes and Three Dimensional Dimple Tubes

Experimental Study Of Condensation Flow Inside Horizontal Smooth, Herringbone And Three Enhanced Surface Tubes

Experimental research on refrigerant condensation heat transfer and pressure drop characteristics in the horizontal microfin tubes

Experimental Study on Condensation in the Outer Annular Region Outside Horizontal Enhanced Tubes

Convective condensation of R410A in micro-fin tubes

Condensation heat transfer and pressure drop characteristics inside smooth and enhanced tubes with R410A and R32

Condensation Characteristics of Flows Inside the Three-Dimensional Enhanced and Smooth Tubes

An Experimental Study of R410A Condensation Heat Transfer and Pressure Drops Characteristics in Microfin and Smooth Tubes with 5 Mm OD

Condensation Heat Transfer in Horizontal Three Dimensional Two-Layer Two-Side Enhanced Tubes

Numerical and experimental investigation on the condensing heat transfer of R134a outside plain and integral-fin tubes

Condensation Pressure Drop and Heat Transfer in 5-Mm-od Micro-Fin Tubes

Condensation Heat Transfer Characteristics On The Outside Of Horizontal Smooth, Herringbone And Enhanced Surface 1eht Tubes