Abstract:Carbon nanotubes (CNTs) are considered an advanced form of carbon. They have superior characteristics in terms of mechanical and thermal properties compared to other available fibers and can be used in various applications, such as supercapacitors, sensors, and artificial muscles. The properties of single-walled carbon nanotubes (SWNTs) are significantly affected by geometric parameters such as chirality and aspect ratio, and testing conditions such as temperature and strain rate. In this study, the effects of geometric parameters and temperature on the mechanical properties of SWNTs were studied by molecular dynamics (MD) simulations using the Large-scaled Atomic/Molecular Massively Parallel Simulator (LAMMPS). Based on the second-generation reactive empirical bond order (REBO) potential, SWNTs of different diameters were tested in tension and compression under different strain rates and temperatures to understand their effects on the mechanical behavior of SWNTs. It was observed that the Young’s modulus and the tensile strength decreases with increasing SWNT tube diameter. As the chiral angle increases, the tensile strength increases, while the Young’s modulus decreases. The simulations were repeated at different temperatures of 300 K, 900 K, 1500 K, 2100 K and different strain rates of 1 × 10−3/ps, 0.75 × 10−3/ps, 0.5 × 10−3/ps, and 0.25 × 10−3/ps to investigate the effects of temperature and strain rate, respectively. The results show that the ultimate tensile strength of SWNTs increases with increasing strain rate. It is also seen that when SWNTs were stretched at higher temperatures, they failed at lower stresses and strains. The compressive behavior results indicate that SWNTs tend to buckle under lower stresses and strains than those under tensile stress. The simulation results were validated by and consistent with previous studies. The presented approach can be applied to investigate the properties of other advanced materials.

Geometry-Dependent Nonlinear Decrease of the Effective Young's Modulus of Single-walled Carbon Nanotubes Submitted to Large Tensile Loadings

Coupled Thermomechanics Of Single-Wall Carbon Nanotubes

Prediction of Young's Modulus of Small-Diameter Single-Wall Carbon Nanotube with Finite Element Method

Dynamic Elastic Modulus of Single-Walled Carbon Nanotubes in Different Thermal Environments

Nonlinear Tensile Deformation Of Single-Walled Carbon Nanotubes With Different Radius And Chirality

A Modified Molecular Structural Mechanics Method for Analysis of Carbon Nanotubes

The Intrinsic Stiffness of Single-Wall Carbon Nanotubes

Effects of Radius and Orientation of Single-Walled Carbon Nanotubes on Their Nonlinear Tensile Deformation Behaviour

Effect of Ending Surface on Energy and Young's Modulus of Single-Walled Carbon Nanotubes Studied Using Linear Scaling Quantum Mechanical Method

Molecular Dynamics Simulations of Effects of Geometric Parameters and Temperature on Mechanical Properties of Single-Walled Carbon Nanotubes

Simulation of the Elastic Response and the Buckling Modes of Single-Walled Carbon Nanotubes

Theoretical Predictions of Size-Dependent Young's and Shear Moduli of Single-Walled Carbon Nanotubes

The effective modulus of super carbon nanotubes predicted by molecular structure mechanics.

Tensile and bending properties of double-walled carbon nanotubes

Higher Order Cauchy-Born Rule Based Study of Chiral Single-Walled Carbon Nanotubes

Temperature-Dependent Elastic Properties of Single-Walled Carbon Nanotubes: Prediction from Molecular Dynamics Simulation

Determination of the Young’s Modulus of Structurally Defined Carbon Nanotubes

Postbuckling of Carbon Nanotubes Subjected to Cyclic Load

A Non-Linear Analysis of the Bending Modulus of Carbon Nanotubes with Rippling Deformations

Effect of a Rippling Mode on Resonances of Carbon Nanotubes.

Elastic Axial Buckling of Carbon Nanotubes Via A Molecular Mechanics Model