Abstract:Molybdenum (Mo), a bcc metal with a melting point of 2,610 degrees C and a density of 10.22 g/cm(3), is an important refractory metal. The refractory properties of molybdenum reflect the high strength of interatomic bonding resulting from the overlap of the 4d-orbitals and the number of bonding electrons available (1).The melting point of molybdenum is exceeded only by those of tungsten and tantalum, among the useful high-temperature metals. This makes molybdenum essentially a "hot strength" material. Molybdenum is ductile at room temperature, with a brittle-ductile transition temperature significantly lower than that of tungsten. The density of molybdenum is approximately 62% of that of tantalum, and is approximately one half of that of tungsten, making molybdenum a good candidate for applications where high-temperature capability, weight considerations, and ductility are key issues.Molybdenum also possesses much greater specific heat than either tantalum or tungsten, making it easier to thermally treat molybdenum to produce structures with low thermal stresses than most other metals. Molybdenum is resistant to most chemical reagents except for oxidizing acids. The relatively low thermal neutron cross section of molybdenum also makes it suitable for nuclear applications. The unique properties of molybdenum make it an ideal material for high-temperature engineering applications. Since the 1960's, molybdenum has also been chosen by many researchers as an ideal material to examine the deformation behavior of bcc metals. These studies have, however, focused on low strain-rate regimes.The deformation characteristics of bcc metals differ markedly from those exhibited by fee metals. For example:1) the yield strength and flow stress of bcc metals increase rapidly with decreasing temperature and increasing strain rate, in contrast to the much more modest trends exhibited by fee metals,2) the activation volume for the deformation of bcc metals is in the range of 5-50b(3) (b = magnitude of Burgers' vector of dislocations), whereas that for fed metals is often 10-100 times greater,3) the increase in the yield point with a decrease in temperature is independent of the strain-hardened state in bcc metals, whereas it is greater for the higher strain-hardened states for fee metals.The study of the deformation behavior of molybdenum is expected to lead to a more detailed understanding of the deformation mechanisms of bcc metals, in particular the refractory metals. The focus of the present work has been on the high strain-rate, high strain response of molybdenum, over a broad range of temperatures. Before presenting our experimental and the corresponding micromechanical modeling results, we briefly review some of the existing relevant contributions.

Experimentally-Based Micromechanical Modeling of Dynamic Response of Molybdenum

Microstructure, Compressive Performance and Wear Resistance of Pure Molybdenum Additively Manufactured Via Laser Powder Bed Fusion

Microstructure and Mechanical Properties of Unalloyed Molybdenum Fabricated Via Wire Arc Additive Manufacturing

Explosion/impact Response of Pure Molybdenum at Ultra-High Strain Rate and Large Strains

Rheological Behavior of Pure Molybdenum at High Temperature Considering Strain Compensation

In-situ SEM Study of Temperature Dependent Tensile Behavior of Wrought Molybdenum

Comparative Study of the Dynamic Deformation of Pure Molybdenum at High Strain Rates and High Temperatures

The Microstructure and Cracking Behaviors of Pure Molybdenum Fabricated by Selective Laser Melting

A Comparative Study on Modified Johnson–Cook and Arrhenius-Type Constitutive Models to Predict the Hot Deformation Behaviour of Molybdenum-Hafnium-Carbide Alloy

Nanoindentation of single crystalline Mo: Atomistic defect nucleation and thermomechanical stability

Mechanical and microstructural responses in molybdenum-rhenium alloys under hot compressions

Revealing the room temperature superplasticity in bulk recrystallized molybdenum

Mechanical properties of Mo-Re alloy based on first-principles and machine learning potential function

Numerical Investigation of the Temperature Dependence of Dynamic Yield Stress of Typical BCC Metals under Shock Loading with a Dislocation-Based Constitutive Model

A new approach to understand the deformation behavior and strengthening mechanism of molybdenum alloy: From single crystal to polycrystal

Ab initio melting curve of molybdenum by the phase coexistence method

Study on Thermal Compression Deformation Behavior and Constitutive Model of Homogenized Mg–5Zn–1Mn Alloy

Ab initio quasi-harmonic thermoelasticity of molybdenum at high temperature and pressure

Lattice dynamics and thermodynamics of molybdenum from first-principles calculations

Liquid metal embrittlement and fracture behavior of three Mo metals in liquid lead-bismuth eutectic

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy