Abstract:The advantages of utilizing activated carbonate additions as a surplus provider of calcium were elucidated in this study. The pozzolanic activity inherent in clays and minerals containing carbonate can be tailored through the de‐hydroxylation of clay and the de‐carbonation of calcite content. Special consideration needs to be given to ensuring the effective activation of schist‐type materials, given the potential for substantial variations between the outcomes of laboratory‐scale and industrial‐scale activation processes for materials characterized by very low thermal conductivity, such as schists. Supplementary cementitious materials (SCMs) are partial substitutes for ordinary Portland cement (OPC) to reduce cost, the production of carbon dioxide (CO2), and fossil fuel consumption. Recent studies illustrated the effectiveness of calcined kaolinite clay as a proper partial replacement for OPC. Hence, schist‐type materials containing sufficient clay contents are regarded as promising candidates for OPC replacement. This study focuses on the possible use of activated calcium carbonates (CaCO3) to augment pozzolanic reactions of schists as a substitute for OPC. The use of activated calcium carbonates proved to be successful in expediting pozzolanic reactions and facilitating the formation of additional calcium aluminosilicate hydrate (C‐A‐S‐H). In this study, the optimal strength performance for blended cement was achieved by adjusting the total carbonate content to 30 wt.% of the schist. The decision to introduce carbonate to the schist was guided by calculations determining the need for an excess of calcium ions to fully harness the potential for C‐A‐S‐H formation. Virgin and augmented schists were activated by up to 80% of their respective potentials by heat treatment. Phase content and decomposition behavior of the active components were investigated by thermogravimetric analysis (TGA), x‐ray diffraction (XRD), and scanning electron microscopy (SEM). Cement paste samples incorporating 30 wt.% replacement of OPC with activated schist SCMs were prepared. The phase distribution and compressive strengths of these samples were assessed at hydration intervals of 2, 7, 28, 50, and 90 days. Cement formulations with activated calcium‐augmented SCMs exhibited compressive strength values at 109%, 101%, 96%, 95%, and 94% compared to pure cement paste at 2, 7, 28, 50, and 90 days, respectively. These values surpassed 90% of the compressive strength of pure OPC at equivalent hydration time points.

Fundamental design of low-carbon ordinary Portland cement-calcium sulfoaluminate clinker-anhydrite blended system

Microstructure Refinement of Calcium-Sulfate-aluminate and Portland Cement (CSA-PC) Hybrids with Accelerated CO2 Curing (ACC)

Understanding the Role of Calcium Silicate Slag in Sodium Carbonate-Activated Green Materials: Influence on Kinetics, Strength, and Efflorescence

Properties and Microstructures of 3D Printable Sulphoaluminate Cement Concrete Containing Industrial By-Products and Nano Clay

Hydration mechanism of calcium sulfoaluminate-activated supersulfated cement

Analysis of theoretical carbon dioxide emissions from cement production: Methodology and application

Factors Influencing the Hydration, Dimensional Stability, and Strength Development of the OPC-CSA-Anhydrite Ternary System

The Synergistic Effect of Calcained Coal-Series Kaolinite and Limestone on the Hydration of Portland Cement

Clinker-Free Cement Based on Calcined Clay, Slag, Portlandite, Anhydrite, and C-S-H Seeding: An SCM-Based Low-Carbon Cementitious Binder Approach

Composition design and pilot study of an advanced energy-saving and low-carbon rankinite clinker

Early Hydration Heat of Calcium Sulfoaluminate Cement with Influences of Supplementary Cementitious Materials and Water to Binder Ratio

Investigation on the preparation of low carbon cement materials from industrial solid waste phosphogypsum: Clinker preparation, cement properties, and hydration mechanism

Sustainable Utilization of Waste Oyster Shell Powders with Different Fineness Levels in a Ternary Supplementary Cementitious Material System

Rheological behavior of Portland clinker-calcium sulphoaluminate clinker-anhydrite ternary blend

Formulation of low clinker blended cements and concrete with enhanced fresh and hardened properties

Properties and microstructure of a low-carbon clinker-free cementitious binder and its extrusion-based printing performance

Influence of C–S–H seed and sodium sulfate on the hydration and strength of limestone calcined clay cement

Effect of CaO Sourced from CaCO3 or CaSO4 on Phase Formation and Mineral Composition of Iron-Rich Calcium Sulfoaluminate Clinker

Compressive strength and environmental impact of sustainable blended cement with high-dosage Limestone and Calcined Clay (LC2)

Optimization of Ca/Si ratio in schists to enhance the pozzolanic supplementary cementitious material for OPC blending