Abstract:Lithium-sulfur (Li-S) battery has been regarded as a promising energy-storage system due to its high theoretical specific capacity of 1675 mAh g(-1) and low cost of raw materials. However, several challenges remain to make Li-S batteries viable, including the shuttling of soluble lithium polysulfide intermediates and pulverization of Li metal anode. Engineering stable electrode-separator interfaces without causing large mass/volume increase of inactive materials and electrolyte uptake is an effective approach to improve the cycling stability of Li-S batteries while maintaining high available energy density. Herein, we report the engineering of a stable electrode-separator interface with an ultrathin conductive polymer nanolayer on the pore walls of both surfaces of the separator via a simple and scalable approach using in-situ vapor-phase polymerization of polypyrrole (PPy) on commercial Celgard separator with only a small increase in overall mass and volume. The inherent hydrophilicity of PPy enables the separator to have enhanced electrolyte uptake, which facilitates homogenous Li+ flux and thus uniform plating and stripping of metallic lithium at the anode side during the charge/discharge processes. Meanwhile, the chemical immobilization effect of PPy suppresses the migration of the soluble polysulfides and improves the stability of the sulfur cathode. We showed that a Li parallel to Li symmetrical cell with the PPy modified separator gave a low and stable overpotential of less than 30 mV for over 250 h' stripping and plating test at 1 mA cm(-2) with a fixed areal capacity of 3 mAh cm(-2), which was significantly better than that using a regular Celgard separator. Using the PPy modified separator, Li-S cell with sulfur/carbon black composite cathode and lithium anode delivered stable cycling for 250 cycles at 0.5 C with a low capacity decay rate of 0.083% per cycle. Even for a Li-S cell with a high-areal-capacity sulfur cathode (4.8 mAh cm(-2)), good cycling stability was achieved. It gave a reversible areal capacity of 3.6 mAh cm(-2) after 150 charge/discharge cycles at 0.2 C with 75.6% capacity retention. Besides, the as-achieved separator showed better thermal stability than the bare counterpart. This work offers an alternative approach for achieving a practical Li-S battery toward high energy density and long cycle life through simple and scalable separator-electrode interface engineering without significant increase in volume and mass.

Efficient thermal management of lithium-sulfur batteries by highly thermally conductive LBL-assembled composite separators

Toward Safe and High-Performance Lithium–Sulfur Batteries Via Polyimide Nanosheets-Modified Separator

A Nonflammable and Thermotolerant Separator Suppresses Polysulfide Dissolution for Safe and Long‐Cycle Lithium‐Sulfur Batteries

A gel polymer electrolyte functionalized separator for high-performance lithium-sulfur batteries

Designing a Multifunctional Separator for High-Performance Li-S Batteries at Elevated Temperature

A Multifunctional Separator Enables Safe and Durable Lithium/Magnesium–Sulfur Batteries under Elevated Temperature

Fast thermal responsive separators toward long-life and safe lithium metal batteries

Designing of multifunctional and flame retardant separator towards safer high-performance lithium-sulfur batteries

Construction of Multifunctional and Flame Retardant Separator Towards Stable Lithium-Sulfur Batteries with High Safety

Multifunctional interlayer with simultaneously capturing and catalytically converting polysulfides for boosting safety and performance of lithium-sulfur batteries at high-low temperatures

Dual-engineered separator for highly robust, all-climate lithium-sulfur batteries

“Three‐in‐one” Strategy: Heat Regulation and Conversion Enhancement of a Multifunctional Separator for Safer Lithium–sulfur Batteries

A Multifunctional Separator for High-Performance Lithium-Sulfur Batteries

Thermal Conductive Aramid Nanofiber/surface-Decorated Alumina Microsphere Composite Separator

A Thermally Managed Separator for Lithium Metal Batteries Operating Safely above 100 °C

Rational Design and Low-Cost Fabrication of Multifunctional Separators Enabling High Sulfur Utilization in Long-Life Lithium-Sulfur Batteries

Engineering Stable Electrode-Separator Interfaces with Ultrathin Conductive Polymer Layer for High-Energy-density Li-S Batteries

Ultralight carbon flakes modified separator as an effective polysulfide barrier for lithium-sulfur batteries

Modification and Functionalization of Separators for High Performance Lithium–Sulfur Batteries

Designing Thermotolerant and Flame-Resistant PAN-based Separator Via Surface Engineering with Heteroatoms Doped Carbon Framework Encapsulated with CoS2 Nanocatalysts Towards Safe Lithium-Sulfur Batteries

High areal loading and long-life cycle stability of lithium-sulfur batteries achieved by a dual-function ZnS-modified separator