Abstract:With the continuous improvement of various armor protection technologies, the armor protection performance has increased significantly, and then the damage performance requirements of armor-piercing ammunition have also increased. In order to improve the penetration ability of the liner, a new three-layer liner structure is designed in this paper. The jet forming process was simulated by AUTODYN software. The mechanism of shaped jet forming of three-layer liner was studied. The reason why the penetration depth of three-layer liner was higher than that of ordinary liner was explained. The influence of three-layer liner on the propagation of detonation wave and the change of pressure when detonation wave acted on liner were found, which provided a new idea for improving the penetration depth of jet. The influence of liner material, cone angle and stand-off on jet forming and penetration was also studied by orthogonal optimization experiment, and the structural parameters with the best penetration performance were obtained. The results show that the pressure at the convergence point increases first and then decreases during the formation of the jet of the three-layer liner. The pressure at the convergence point when the three-layer liner material is from low impedance to high impedance from the outside to the inside is much larger than the pressure at the convergence point from high impedance to low impedance. When the three-layer liner material is Al 2024-Copper–Tantalum from the outside to the inside, the pressure at the convergence point of the three-layer liner at different times is higher than that of the double-layer liner and the single-layer liner. Reasonable matching of different impact impedance materials in the three-layer liner can greatly improve the pressure value of the detonation wave acting on the cone liner. The maximum pressure at the convergence point on the axis is 39.10 GPa, which is 22.00% higher than that of the double-layer liner at the convergence point, and 53.03% higher than that of the single-layer liner at the convergence point. The orthogonal design test scheme is simulated and analyzed. The penetration depth is taken as the observation index, and the range analysis is adopted. The results show that the material matching of the three-layer liner has the greatest influence on the depth of the jet penetrating the target plate, followed by the cone angle of the three-layer liner. Relatively speaking, the stand-off has the least influence on the result. Reasonable matching of materials with different impact impedances in the three-layer liner can maximize the penetration depth of the jet into the target plate.

Directional rock blasting using shaped charges using combined charge liners with different shapes

Research on directional rock blasting based on different slotted pipe materials of the combined charge structure

Research on the crack formation mechanism of shaped charge blasting and the new dual-shaped charge blasting technology

Experimental research and application of drilling and blasting with directional damage-reduction shaped charge

Directional Fracture Controlled Blasting Technology of Bidirectional Cumulative Energy for Roadway Rock Surrounding

Study on crack propagation mechanism and charge structure optimization of tunnel shaped charge hydraulic blasting

Formation and Penetration Properties of a Shaped Charge with Zr41.2Ti13.8Cu12.5Ni10Be22.5 Liner

Study on Shaped Charge Technique Based on the Requirements of Rock Charge Hole

Damage Analysis of Concrete Structure under Multidirectional Shaped Charge Blasting Using Model Experiment and Ultrasonic Testing

Application of W/Zr amorphous alloy for shaped charge liner

The effect of three-layer liner on the jet formation and penetration capability of shaped charge jet

Study on Forming Law and Penetration of a Spherical Cone Composite Structure Liner Based on the Explosion Pressure-Coupling Constraint Principle

Study on the detonation wave propagation of shaped charge with three-layer liner and its driving characteristics to liner

Numerical Simulation and Analysis of a Combined Shaped Charge

Influence mechanism of the diameter of the energy accumulation hole on the bi-directional cumulative tension blasting

Numerical Simulation of Effect of Liner’s Structure on Performance of Shaped Charge Jet

The Influence of Closed-Cell W-Shaped Liner Parameters on the Penetration Performance of Integral Annular Shaped Charge

Study on the influence of slit pipe wall thickness on the rock breaking effect of slit charge explosion

Effects of the initiation position on the damage and fracture characteristics of linear-charge blasting in rock

Rock damage control for large-diameter-hole lateral blasting excavation based on charge structure optimization

Study on the effect of shape parameters and initiation points of rectangular high explosive on the spatial distribution of blast loads