Abstract:The growing demand for clean and efficient energy sources has been a direct result of the serious effect on the climate and the environment associated with high emissions of pollutants that are mainly produced by fossil fuel-based energy generators. Currently, green technology like proton exchange membrane fuel cells (PEMFC) can produce zero-emissions energy power by primarily using the electrochemical reactions of hydrogen and oxygen to generate electrical energy. Additionally, due to their high activity, Platinum (Pt) nanoparticles (NPs) distributed on a carbon catalyst support are considered the most efficient catalyst materials used in this technology. However, the main drawbacks of this technology are (i) the scarcity of Pt, making it very expensive for widespread fuel cell application and commercialization, and (ii) the susceptibility of the carbon support to corrosion and degradation when operating even at the most typical PEMFC conditions. Carbon corrosion can induce the loss of Pt NPs' active surface area when Pt detaches from the carbon support or agglomerates into larger Pt NPs, leading to premature performance losses in a PEMFC. In this work, we propose a novel approach to prevent carbon corrosion by selectively depositing a corrosion-resistant thin layer (~2 nm) of titanium nitride (TiN) only on the surface of the carbon support while the catalyst centers are left uncoated and accessible for reagent reactions (oxygen O and H + protons). TiN was used as the coating material because of its attractive properties, such as electronic conductivity, enough to enable the free movement of electrons from the current collector toward the catalytic centers. The TiN layer would also act as an anchoring mechanism of Pt NPs, preventing their mobility on the carbon support and subsequent agglomeration. The deposition of TiN layers was carried out at 150°C with a hollow-cathode plasma-assisted atomic layer deposition (HCPA-ALD) reactor and using tetrakis(dimethylamino)titanium (IV) as the metal precursor in Ar/N 2 plasma, from which nitrogen was used as the co-reactant. Before HCPA-ALD, to prevent TiN from depositing on top of the Pt NPs, the surface of Pt NPs was selectively coated with a thin film of oleylamine (OAm), a polymer that would only absorb onto Pt NPs, which is later removed from the catalyst system (after the HCPA-ALD process is finished) by heat treatment at 185°C. Here we will mainly focus on the TiN deposition process and the subsequent transmission electron microscopy (TEM) characterization performed on these nanoparticles, which allows us to prove the successful formation of homogenous coatings and architecture characteristics of these nanoparticles after oleylamine application and TiN deposition. Electrochemical characterization, including cyclic voltammetry (CV) and oxygen reduction reaction (ORR), was performed in a rotating disc electrode (RDE) to further confirm the activity and effectiveness of our designed catalyst. Our preliminary results have shown that highly conformal TiN can be successfully grown onto Pt/C nanoparticles (as powders) by using HCPA-ALD with a custom-made agitator mechanism. The second phase of this research will be focused on inspecting the degradation mechanisms this novel catalyst system experiences after potential cycling in a Membrane Electrode Assembly (MEA).

Structure – Catalytic Behavior Relationships in TiO2-Carbon Composite Supported Pt Electrocatalysts: A Case Study

Systematic Study of the Electronic, Carbon, and N-Doping Effects of CoMn-Oxide Composites as Bifunctional Oxygen Electrocatalysts

Composites of Titanium-Molybdenum Mixed Oxides and Non-Traditional Carbon Materials: Innovative Supports for Platinum Electrocatalysts for Polymer Electrolyte Membrane Fuel Cells

Preparation of Pt electrocatalyst supported by novel, Ti(1−x)MoxO2-C type of composites containing multi-layer graphene

Influence of a carbon support on the catalytic activity and durability of the Pt-based electrocatalysts

Electrocatalytic Properties of Mixed-Oxide-Containing Composite-Supported Platinum for Polymer Electrolyte Membrane (PEM) Fuel Cells

The role of carbon support morphology in the formation of catalytic layer of solid-polymer fuel cell

Reductive Treatment of Pt Supported on Ti0.8Sn0.2O2-C Composite: A Route for Modulating the Sn-Pt Interactions

Catalytic effects of graphene structures on Pt/graphene catalysts

Synthesis of an improved hierarchical carbon-fiber composite as a catalyst support for platinum and its application in electrocatalysis

Synthesis and Characterization of Platinum on Carbon Nanoparticles Selectively Coated with Titanium Nitride (TiN)

Few-layered nitrogen-doped graphene wrapped three-dimensional titanium oxide flower as a robust support for Pt nanoparticles in catalyzing oxygen reduction reaction

On the Influence of Composition and Structure of Carbon-Supported Pt-SnO2 Hetero-Clusters onto Their Electrocatalytic Activity and Durability in PEMFC

Understanding the Oxygen Reduction Reaction Activity and Oxidative Stability of Pt Supported on Nb-Doped TiO2

Electrochemical Behavior of Pt Nanoparticles Supported on Meso- and Microporous Carbons for Fuel Cells

Strong Interaction between Titanium Carbonitride Embedded in Mesoporous Carbon Nanofibers and Pt Enables Durable Oxygen Reduction

Revealing the Nanostructure of Mesoporous Fuel Cell Catalyst Supports for Durable, High-Power Performance

Synthesis, characterization and comparison of polythiophene–carbon nanocomposite materials as Pt electrocatalyst supports for fuel cell applications

Nitrogen Doped Titania Stabilized Pt/C Catalyst Via Selective Atomic Layer Deposition for Fuel Cell Oxygen Reduction

Improved stability of mesoporous carbon fuel cell catalyst support through incorporation of TiO2

Pt/TiN–TiO2 Catalyst Preparation and Its Performance in Oxygen Reduction Reaction