Abstract:Background: A major problem which hinders the applications of neural prostheses is the inconsistent performance caused by tissue responses during long-term implantation. Therefore, polymer characterized by good biocompatibility and high ionic conductivity was used in this study to coat the electrode, aiming to improve biocompatibility and enhance stability for long-term implantation. Objective: To investigate the ionic conductivity of synthesized polyurethane and cellular compatibility to PC12 cells and cerebellar granule neurons (CGNs). Design, time and setting: A contrast study was performed at the Neural Electrode Research Laboratory, College of Chemistry and Molecular Science, Wuhan University, and the Life Science and Technology College of Huazhong University of Science and Technology from October 2007 to April 2008. Materials: Polymer precursor was synthesized by 2,4-isophorone diisocyanate and polyethylene glycol; thereafter, water (crosslinking agent) and dibutyl tin dilaurate (catalyst) were used to form polyurethane. Methods: Silicon rubber films were treated with plasma in the air for 1 minute, and then the synthesized polyurethane solution was evenly spread on the surface of silicon rubber films. In addition, silicon rubber films underwent no treatment were used as the controls. Main outcome measures: Functional group of synthesized polyurethane was analyzed using infrared tester; cyclic voltammetry was measured before and after coating polyurethane on the testing electrode; adhesion of PC12 cells and CGNs to different material surfaces was observed; relative survival rate of cells on different material surfaces was calculated. Results: The results of the infrared test suggested that polyethylene glycol and isophorone diisocyanate (IPDI) reacted completely. The results of cyclic voltammetry showed that there was high ionic mobility within the polyurethane film and that the presence of the film did not affect the electrochemical performance of the electrodes. Adhesion and growth of PC12 and CGNs were better on polyurethane coating compared to the control material. The MTT results suggested that cell survival was significant higher on polyurethane-coated silicon rubber compared to the control material (P < 0.001). Conclusion: Synthesized polyurethane with polyethylene glycol is a very promising biomedical material, which not only exhibits a high ionic conductivity, but also has good cellular compatibility with PC12 and CGNs.

Bio-Compatibility and Bio-Insulation of Implantable Electrode Prosthesis Ameliorated by A-174 Silane Primed Parylene-C Deposited Embedment

Study of Polyimide-Based Bio-Electrode Array for Retinal Prostheses

Parylene C as an Insulating Polymer for Implantable Neural Interfaces: Acute Electrochemical Impedance Behaviors in Saline and Pig Brain In Vitro

In vitro and in vivo evaluation of a photosensitive polyimide thin-film microelectrode array suitable for epiretinal stimulation

Flexible Microelectrode Array on Parylene for Subretinal Stimulation and Its Biocompatibility Test

Improving Adhesion Strength Between Layers of an Implantable Parylene-C Electrode

Development Of Flexible Neural Microelectode Arrays Based On Parylene For Retinal Prosthesis

Ultrathin, High Capacitance Capping Layers for Silicon Electronics with Conductive Interconnects in Flexible, Long‐Lived Bioimplants

Polyethylene Glycol-Containing Polyurethane Hydrogel Coatings for Improving the Biocompatibility of Neural Electrodes

An Electroactive Hybrid Biointerface for Enhancing Neuronal Differentiation and Axonal Outgrowth on Bio-Subretinal Chip

Cytocompatibility of polyurethane-coated implanted neural electrode

Fabrication and Characterization of a Parylene-Based Three-Dimensional Microelectrode Array for Use in Retinal Prosthesis

Parylene-based Implantable Pt-black Coated Flexible 3-D Hemispherical Microelectrode Arrays for Improved Neural Interfaces

Polyurethane/Poly(Vinyl Alcohol) Hydrogel Coating Improves the Cytocompatibility of Neural Electrodes

In vitro biocompatibility of a platinum-electrode embedded photosensitive polyimide (Durimide) retinal prosthesis.

Fabrication and in Vitro Biocompatibility of Flexible Polyimide-Based Microelectrode Array for Visual Prosthesis

Poly(vinyl Alcohol)/poly(acrylic Acid) Hydrogel Coatings for Improving Electrode–neural Tissue Interface

Significantly improved cell affinity of polydimethylsiloxane enabled by a surface-modified strategy with chemical coupling

Electrically Conductive Functionalization of Cured Polyether Ether Ketone with Improved Bioactivity by Surface-Polymerization of Polyaniline

Conducting Polymer-Hydrogel Interpenetrating Networks for Improving the Electrode-Neural Interface.

The Design and Preparation of a Flexible Bio-Chip for Use As a Visual Prosthesis, and Evaluation of Its Biological Features