Abstract:WC–Co cemented carbides are a class of hard composite materials of great technological importance. They are widely used as tool materials in a large variety of applications that have high demands on hardness and toughness, including mining, turning, cutting and milling. The HVOF (high velocity oxygen fuel) technology has been very successful in spraying wear resistant WC–Co coatings with higher density, superior bond strengths and less decarburization than many other thermal spray processes, attributed mainly to its high particle impact velocities and relatively low peak particle temperatures. The degree of decomposition and bond strength is directly related to relevant particle parameters such as velocity, temperature and state of melting or solidification. These are consecutively related to process parameters such as powder particle size distribution, carrier gas flow rate, and fuel type employed. To obtain detailed particle data important for thermal spraying, mathematical models are developed in the present paper to predict the particle dynamic behavior in a liquid fuelled HVOF thermal spray gun. The particle transport equations are coupled with the three-dimensional, chemically reacting, turbulent gas flow, and solved in a Lagrangian manner. The melting and solidification within the particles as a result of heat exchange with the surrounding gas flow is solved numerically. The in-flight characteristics of WC–Co particles are studied and the effects of carrier gas parameters on particle behavior are examined. The results demonstrate that WC–Co particles smaller than 5μm in diameter undergo melting and solidification prior to impact while most particles never reach liquid state during the HVOF thermal spraying. The flow rate of carrier gas has considerable influence on particle dynamics as well as deposition on substrate. At higher flow rate the powder particles are redirected further away from the substrate center, while smaller flow rate results in better heating, higher impact velocity and deposition closer to the substrate center.

Development of fine WC-NiCr powder coatings by optimising HVOF spray parameters

Effect of Particle and Carbide Grain Sizes on a HVOAF WC-Co-Cr Coating for the Future Application on Internal Surfaces: Microstructure and Wear

Multi response optimization of HVOF process parameters in low carbon steels

Computational Simulation of Thermally Sprayed WC–Co Powder

Thermal Spray of Cemented Carbide Coatings in Off-Angle Spraying: Correlations Between Process, Coating Features/Characteristics and Performance

Optimization of HVOF Spray Parameters for WC-Co-Cr Coatings on AMMC (Al-RHA) for Pump Impeller Protection

HVOF Spray Performance Optimization Analysis and Experimental Research of WC–12Co Coating on Ti Alloy

Investigation of Novel Nano-carbide WC/CoCr Coatings Applied by HVAF

Influence of Spray Parameters on Sliding Wear Properties of HVOF Sprayed Fe-Based Amorphous Coatings

Characterization on microstructures and properties of WC-CoCr coating deposited by HVAF and HVOF processes

Effect of Flame Conditions on Abrasive Wear Performance of Hvof Sprayed Nanostructured Wc-12co Coatings

Thick WC-12Co Coatings on Bearing Steel Fabricated by Low-Temperature High-Velocity Fuel Spray Process

Multimodal Coatings: A New Concept in Thermal Spraying

Influence of HVOF spraying parameters on microstructure and mechanical properties of FeCrMnCoNi high-entropy coatings (HECs)

Enhancing Tribological Characteristics of Titanium Grade-5 Alloy through HVOF Thermal-Sprayed WC-Co Nano Coatings by TOPSIS and Golden Jack Optimization Algorithm

Numerical Analysis of High-Velocity Oxygen Fuel Thermal-Spray Process for Fe-Based Amorphous Coatings

Microstructure and mechanical property of high velocity oxy-fuel sprayed WC-Cr3C2-Ni coatings

Influence of WC Particle Size on the Mechanical Properties and Residual Stress of HVOF Thermally Sprayed WC–10Co–4Cr Coatings

Effect of solid carbide particle size on deposition behaviour, microstructure and wear performance of HVOF cermet coatings

Numerical Modeling the Bonding Mechanism of HVOF Sprayed Particles

Investigation on Microstructure, Mechanical and Wear Properties of HVOF Sprayed Composite Coatings (WC-Co + CR) On Ductile Cast Iron