Abstract:Super- hydrophobic surfaces have attracted great research interest due to their novel performance as self-cleaning, anti-fog, and anti -oxidation. In this work,a new approach,based on elastomeric templates and UV-curable resins I has been developed to prepare super- hydrophobic surfaces. Poly( dimethylsiloxane) (PDMS, Sylgard 184) was purchased from Dow Coming and used to replicate lotus-leaf surfaces. In the replication step, PDMS blocks were prepared through replica molding against lotus-leaf surfaces. PDMS prepolymer was prepared by mixing the elastomer base and curing agent in a ratio of 10: 1. After 20 min, the PDMS prepolymer was poured into molds within fresh lotus-leaf surfaces as masters. Then the prepolymer was cured in 40 degrees C oven for 4 h. After curing and peeling off, the PDMS blocks with negative lotus-leaf surfaces' structures were obtained. Microscope observation indicates that the PDMS blocks' surfaces were featured with hollow cavities of 7 similar to 12 microns in diameter. The PDMS blocks could be used as stamps in the following curling step of ultraviolet (UV)-curable prepolymers, which consist of oligomer,cross-linking agent, reactive monomer, and photo- initiator. In the experiment, isobomyl acrylate, siliconized urethane acrylate, benzoin dimethyl ether and dipentaerythritol pentaacrylate were used as monomer, oligomer, photoinitiator and crosslinking agent, respectively. In a typical process, UV-curable prepolymer was prepared by mixing monomer, oligomer, photoinitiator and crosslinking agent in a ratio of 10: 68: 2: 20. Then the prepolymer was put into a 0. 085 MPa vacuum oven to remove air bubble. The prepolymer was spread on substrates ( silicon wafer or glass slide), pressed by the PDMS stamp with replicated lotus-leaf surface. Finally, the UV-curable prepolymer covered with the PDMS stamp was exposed to UV-light (500 mu W/cm(2) After curing for 15 min, the PDMS stamp was peeled off, and the cured sample was store in 40 degrees C oven for 5 h before further experiments. Measured by scanning electron microscopy ( SEM, Hitachi S-4500), a large amount of papillary microstructures with an average diameter of about 7 - 10 microns and average height of 10 similar to 18 microns could be seen on the surfaces. These papillary microstructures are replicas of the surface patterns of the lotus leaves. The obtained surfaces had water contact angles larger than 150 degrees and small sliding angles, exhibiting fascinating super- hydrophobicity like lotus-leaf surfaces. Obviously, the replicated papillary microstructures played important role in the increase of surface hydrophobicity from about 105 degrees (smooth film surface) to 157 degrees. This result can be explained with the Wenzel theory. Factors influencing the wettability of resulted surfaces, such as content of monomer, cross-linking agent, initiator and light irradiation time, were also studied in detail. Experiments showed that the surface contact angles increase with the content of photoinitiator before 0. 7 % and decrease with the content of crosslinking agent when larger than 20 % A monomer content of about 10% and irradiation time longer than 10 min were also preferable for achieving high hydrophobicity. Combining the advantages of soft- I lithographic and UV-curing techniques, this approach can be potentially applied in fabrication of large-area super- hydrophobic surfaces.

Micropatterned Hydrogel‐Elastomer Hybrids for Flexible Wet‐Style Superhydrophobic Antifogging Tapes

Micropatterned Hydrogel‐Elastomer Hybrids for Flexible Wet‐Style Superhydrophobic Antifogging Tapes (Adv. Funct. Mater. 34/2024)

Fabrication of Long‐Lasting Superhydrophilic Anti‐Fogging Film Via Rapid and Simple UV Process

Fabrication of Robust, Anti-reflective, Transparent Superhydrophobic Coatings with a Micropatterned Multilayer Structure

Robust and Stable Transparent Superhydrophobic Polydimethylsiloxane Films by Duplicating Via a Femtosecond Laser-Ablated Template

Fast‐Crosslinking Enabled Self‐Roughed Polydimethylsiloxane Transparent Superhydrophobic Coating and Its Application in Anti‐Liquid‐Interference Electrothermal Device

Superhydrophobic Surface with Controllable Adhesion for Anti‐Roof‐Collapse Application in Flexible Microfluidics

Biomimetic Slippery PDMS Film with Papillae-Like Microstructures for Antifogging and Self-Cleaning

Large-Area Stable Superhydrophobic Poly(dimethylsiloxane) Films Fabricated by Thermal Curing Via a Chemically Etched Template.

Construction of superhydrophobic PDMS@PS-SiO 2 films with self-cleaning properties via a simple template approach for efficient water harvesting

Femtosecond Laser Weaving Superhydrophobic Patterned PDMS Surfaces with Tunable Adhesion

Super-Hydrophobic PDMS Surface with Ultra-Low Adhesive Force

Transparent, self-cleaning and waterproof surfaces with tunable micro/nano dual-scale structures

Controllable adhesive superhydrophobic surfaces based on PDMS microwell arrays

Patterning a Superhydrophobic Area on a Facile Fabricated Superhydrophilic Layer Based on an Inkjet-Printed Water-Soluble Polymer Template

Stretchable Anti‐Fogging Tapes for Diverse Transparent Materials

Flexible Broadband Light Absorbers with a Superhydrophobic Surface Fabricated by Ultraviolet-assisted Nanoimprint Lithography

Multifunctional Superhydrophobic Surfaces Templated from Innately Microstructured Hydrogel Matrix

PREPARATION OF SUPER-HYDROPHOBIC SURFACES BY USING ELASTOMER TEMPLATES AND UV-CURABLE RESIN

Flexible, transparent, and durable slippery liquid‐infused porous surface achieved by void‐centered PVDF‐co‐HFP membrane for self‐cleaning antifog coating

Ultra-high performance flexible and controllable superhydrophobic films based on microsphere/micro-pyramid hierarchical arrays