Abstract:Proton beam therapy can deliver a high radiation dose to a tumor without significant damage to surrounding healthy tissue or organs. One way of verifying the delivered dose distribution is to image the short-lived positron emitters produced by the proton beam as it travels through the patient. A potential solution to the limitations of PET imaging in proton beam therapy is the development of a high sensitivity, in situ PET scanner that starts PET imaging almost immediately after patient irradiation while the patient is still lying on the treatment bed. A partial ring PET design is needed for this application in order to avoid interference between the PET detectors and the proton beam, as well as restrictions on patient positioning on the couch. A partial ring also allows us to optimize the detector separation (and hence the sensitivity) for different patient sizes. Our goal in this investigation is to evaluate an in situ PET scanner design for use in proton therapy that provides tomographic imaging in a partial ring scanner design using time-of-flight (TOF) information and an iterative reconstruction algorithm. GEANT4 simulation of an incident proton beam was used to produce a positron emitter distribution, which was parameterized and then used as the source distribution inside a water-filled cylinder for EGS4 simulations of a PET system. Design optimization studies were performed as a function of crystal type and size, system timing resolution, scanner angular coverage and number of positron emitter decays. Data analysis was performed to measure the accuracy of the reconstructed positron emitter distribution as well as the range of the positron emitter distribution. We simulated scanners with varying crystal sizes (2-4 mm) and type (LYSO and LaBr(3)) and our results indicate that 4 mm wide LYSO or LaBr(3) crystals (resulting in 4-5 mm spatial resolution) are adequate; for a full-ring, non-TOF scanner we predict a low bias (<0.6 mm) and a good precision (<1 mm) in the estimated range relative to the simulated positron distribution. We then varied the angular acceptance of the scanner ranging from 1/2 to 2/3 of 2π; a partial ring TOF imaging with good timing resolution (≤600 ps) is necessary to produce accurate tomographic images. A two-third ring scanner with 300 ps timing resolution leads to a bias of 1.0 mm and a precision of 1.4 mm in the range estimate. With a timing resolution of 600 ps, the bias increases to 2.0 mm while the precision in the range estimate is similar. For a half-ring scanner design, more distortions are present in the image, which is characterized by the increased error in the profile difference estimate. We varied the number of positron decays imaged by the PET scanner by an order of magnitude and we observe some decrease in the precision of the range estimate for lower number of decays, but all partial ring scanner designs studied have a precision ≤1.5 mm. The largest number tested, 150 M total positron decays, is considered realistic for a clinical fraction of delivered dose, while the range of positron decays investigated in this work covers a variable number of situations corresponding to delays in scan start time and the total scan time. Thus, we conclude that for partial ring systems, an angular acceptance of at least 1/2 (of 2π) together with timing resolution of 300 ps is needed to achieve accurate and precise range estimates. With 600 ps timing resolution an angular acceptance of 2/3 (of 2π) is required to achieve satisfactory range estimates. These results indicate that it would be feasible to develop a partial-ring dedicated PET scanner based on either LaBr(3) or LYSO to accurately characterize the proton dose for therapy planning.

Production of carbon-11 for PET preclinical imaging using a high-repetition rate laser-driven proton source

Radioisotopes production using lasers: from basic science to applications

Deuteron-induced reactions generated by intense Lasers for PET isotope production

Radioisotope production using lasers: From basic science to applications

Hybrid in-beam PET- and Compton prompt-gamma imaging aimed at enhanced proton-range verification

Production of Medical Radioisotopes with High Specific Activity in Photonuclear Reactions with $γ$ Beams of High Intensity and Large Brilliance

Quasi-real-time range monitoring by in-beam PET: a case for 15O

Design considerations for a pulse line ion accelerator (PLIA)-based PET isotope generator

A Laser-Driven Nanosecond Proton Source for Radiobiological Studies

Reaction yields and angular distributions of prompt γ -rays for range verification in proton therapy using 18O

Liquid Xenon Detectors for Positron Emission Tomography

Laser initiated p-11B fusion reactions in petawatt high-repetition-rates laser facilities

Generation of Medical Isotopes 47-Sc, 67-Cu Through Laser-Induced (γ, P) Reaction

Enhanced positron acceleration driven by femto-second laser pulses irradiating structured targets

Multicenter Experience with Good Manufacturing Practice Production of [11C]PiB for Amyloid Positron Emission Tomography Imaging

New methodologies for the preparation of carbon-11 labeled radiopharmaceuticals

Design study of an in situ PET scanner for use in proton beam therapy

Offline imaging of positron emitters induced by therapeutic helium, carbon and oxygen ion beams with a full-ring PET/CT scanner: experiments in reference targets

Roadmap toward the 10 ps time-of-flight PET challenge

Simulations of a micro-PET system based on liquid xenon

160 MeV laser-accelerated protons from CH2 nano-targets for proton cancer therapy