Abstract:Industrially, lithium-ion battery cathodes are manufactured through a wet slurry mixing and coating process. There is great interest in replacing the presently-used N-methyl-2-pyrrolidone (NMP) solvent with water due to the cost and toxicity associated with NMP. In this study, the modifications made to the active materials as a result of water exposure were studied and two materials, LiMn2O4 (LMO) and LiNi0.8Co0.15Al0.05O2 (NCA), were assembled in high-performing aqueous-processed cathodes for the first time. Five cathode active materials were the subject of this study: LiCoO2 (LCO), LiFePO4 (LFP), LMO, NCA, and LiNi0.5Mn0.3Co0.2O2 (NMC532). All materials exposed to DI water exhibited rapid increases in pH over the first 10 min, with stable pH values ranging from 9.0 (LFP and LMO) to 12.5 (NCA). Given that the protective aluminum oxide layer on the current collector breaks down at a pH of 8.5, corrosion is predicted for all materials, with NCA being the most extreme case. Pristine samples of the same five materials were submerged in water for 24 h, then the moisture was dried in a vacuum oven. The crystal structures of these materials (henceforth referred to as the wetted samples) were evaluated using X-ray diffraction and compared with pristine samples. No changes were observed in the crystal structure of any material as confirmed by Rietveld refinement. X-ray photoelectron spectroscopy was used to evaluate the changes of the surface composition of each wetted and pristine material. Based on inductively coupled plasma-mass spectrometry results, the amount of Li and transition metal leaching in water was found to be independent of time in excess of 1 h, and the amount of Li leaching in water for NCA was found to be five times that of NMC532 and more than 30 times that of the other materials. As a result, using a traditional aqueous slurry formulation (active material, carbon black, emulsion binder, carboxymethylcellulose thickener) resulted in a severely cracked and unusable NCA cathode. By including high-molecular weight polyacrylic acid (PAA), the adhesion of the cathode was restored. Half coin cells of this PAA-processed and an NMP-processed NCA cathode were constructed using punches with 1.7 mAh·cm-2 areal capacity and a charge and discharge rate of C/3 between 3.0-4.3 V. The initial capacity of the PAA-processed NCA cathode was slightly lower (176.3 mAh·g-1 to 185.2 mAh·g-1), though it did exhibit better capacity retention through 100 cycles (84.2% to 78.1%).

Deactivation of Partially (dis)Charged LNMO in Contact with Water by Electrochemical Protonation of Li(1 − x)Ni0.5Mn1.5O4

Enhanced Stability at the Electrode-Electrolyte Interface in Ionic Liquid Electrolyte for 5 V Lithium-Ion Rechargeable Batteries

Surface Structure Evolution and its Impact on the Electrochemical Performances of Aqueous‐Processed High‐Voltage Spinel LiNi0.5Mn1.5O4 Cathodes in Lithium‐Ion Batteries

High reactivity of the nickel-rich LiNi1-x-yMnxCoyO2 layered materials surface towards H2O/CO2 atmosphere and LiPF6-based electrolyte

Improved Li-ion Diffusion and Stability of a LiNi0.5Mn1.5O4 Cathode Through in Situ Co-Doping with Dual-Metal Cations and Incorporation of a Superionic Conductor

Thermodynamically Spontaneously Intercalated H3O+ Enables LiMn2O4 with Enhanced Proton Tolerance in Aqueous Batteries

Lithium and transition metal dissolution due to aqueous processing in lithium-ion battery cathode active materials

Proton-exchange Induced Reactivity in Layered Oxides for Lithium-Ion Batteries

Enabling Aqueous Processing for Low/No-Cobalt Lithium-Ion Battery Cathode Active Materials

On the Composition of LiNi0.5Mn1.5O4 Cathode Active Materials

One-step calcination synthesis of interface-coherent crystallized and surface-passivated LiNi0.5Mn1.5O4 for high-voltage lithium-ion battery

Studies of Lini0.5mn1.5o4 As A Positive Electrode for Li-Ion Batteries: M3+ Doping (M = Al, Fe, Co and Cr), Electrolyte Salts and Lini0.5mn1.5o4/Li4ti5o12 Cells

Understanding the Role of NH 4 F and Al 2 O 3 Surface Co-modi fi cation on Lithium-Excess Layered Oxide Li 1 . 2 Ni 0 . 2 Mn 0 . 6 O 2

Addressing Mn Dissolution in High‐Voltage LiNi0.5Mn1.5O4 Cathodes via Interface Phase Modulation

The Electrochemical Performance Deterioration Mechanism of LiNi0.83Mn0.05Co0.12O2 in Aqueous Slurry and a Mitigation Strategy

Electrolyte Additive Therapy Realizes Simultaneous Ni and Mn Redox for Spinel LiNi0.5Mn1.5O4 Cathode at 2.3–4.95 V

Removing lithium residues via H3BO3 washing and concurrent in-situ formation of a lithium reactive coating on Ni-rich cathode materials toward enhanced electrochemical performance

Enhancement of LiNi0.5Mn1.5O4 Cathode Materials Through Interfacial Modification of Amorphous Al2O3 in Lithium Ion Batteries

In situ lithiation modulation of LiNi0.8Co0.1Mn0.1O2 as bifunctional electrocatalysts for highly efficient overall water splitting

Exploring the Mechanisms of LiNiO2 Cathode Degradation by the Electrolyte Interfacial Deprotonation Reaction

Understanding the Role of Lithium Borate as the Surface Coating on High Voltage Single Crystal LiNi0.5Mn1.5O4