Abstract:Adhesive bonding has gained increasing acceptance in joining pultruded glass fiber reinforced polymer (GFRP) sections. However, one of the major issues hindering the widespread application of adhesive bonding in building and construction industries is the difficulty in predicting the mechanical behavior of the joints in the presence of adhesion defects. This paper investigates the damage tolerance of the adhesively bonded pultruded GFRP double-strap joints under quasi-static tensile loading using finite element analysis. Defects of various locations (along the bond length), sizes, and numbers were embedded within the bondline. A two-dimensional (2D) stress analysis was conducted to assess the effects of the bondline defects on the out-of-plane displacement, stress distribution, and peak stresses of the joints. Three-dimensional (3D) progressive damage models were further developed to predict residual joint capacity and provide insights into the effects of the adhesion defects on the damage mechanism of the joints. The progressive damage model uses the cohesive zone model (CZM) to simulate progressive interlaminar damage within the adherends as well as adhesive-FRP interface debonding. The proposed FE model was validated with published experimental data, and an excellent correlation was found between experimental and numerical results. The validated model was then used in a parametric study to assess the effects of design parameters such as adhesive types (from highly brittle to highly ductile) and joint geometry (adhesive chamfering, adherend chamfering, and recessing) on the damage tolerance of adhesively bonded joints. This paper also reports a comparative study on the damage tolerance between GFRP double-strap, single-strap, and single-step joints. The stress analysis results revealed that the presence of the bondline defects could increase the out-of-plane displacement of the adherends and the peak shear and peel stresses at the overlap ends. High-stress concentrations were also observed in regions adjacent to the defect extremities. The double-strap joints exhibited better damage tolerance than the single-strap and single-step lap joints. The damage tolerance of the joints can be improved by using stress-reduction methods such as adhesive chamfering, adherend chamfering, and recessing.

Ultrasonic reflection characteristics of FRP-to-FRP bonded joints with thick adhesive layers for bonding evaluation: Theoretical analysis

Evaluating interfacial bonding quality of multilayered structure based on ultrasonic testing technology

Study on Ultrasonic Vibration-Assisted Adhesive Bonding of Cfrp Joints

Fracturing behaviors of FRP-strengthened concrete structures

Effect of Adhesive Properties on the Bond Behaviour of Externally Bonded FRP-to-concrete Joints

Experimental Behaviour Of Cfrp-To-Steel Bonded Interfaces

On interfacial fracture in FRP-strengthened structures

Effect of Frp-To-Steel Bonded Joint Configuration on Interfacial Stresses: Finite Element Investigation

NUMERICAL ANALYSIS AND EXPERIMENTAL RESEARCH FOR ACOUSTIC-OPTICAL FIBER BASED DETECTION OF INTERFACIAL DAMAGE IN FRP-RETROFITTED STRUCTURES

The effects of environments and adhesive layer thickness on the failure modes of composite material bonded joints

Bond and slip relationship at the interface of bonded FRP and concrete

Experimental Research and Finite Element Analysis on the Bonding Behavior of Cfrp-Concrete Interface

EXPERIMENTAL INVESTIGATION ON ADHESIVE BONDED JOINTS OF CARBON FIBER COMPOSITE LAMINATES CONTAINING DISBOND DEFECT

Ultrasonic Vibration-Strengthened Adhesive Bonding of CFRP-to-aluminum Joints

Improvement of interface anchoring by ultrasonic vibration for adhesively bonded CFRP/Al joints

Investigation of Residual Strength in CFRP Double-Adhesive Single Lap Bonded Joints after Low-velocity Impact

Numerical Analysis Of Debonding Mechanisms In Frp-Strengthened Rc Beams

Numerical Investigations on the Damage Tolerance of Adhesively Bonded Pultruded GFRP Joints with Adhesion Defects

Analytical Solution for FRP-to-concrete Bonded Joints Considering Local Unloading and Reloading

Investigation on Fracture Behavior of FRP-Concrete Interface under Direct Shear

Effects of mechanical properties of adhesive and CFRP on the bond behavior in CFRP-strengthened steel structures