Abstract:Publication date: 19 August 2022 Source: Materials Science Forum Vol. 1068 Author(s): Osama Ali Ahmed Awan, Babar Saeed, Muhammad Arslan Shehzad, Muhammad Asadullah Khan Composites have a wide range of applications in the field of robotics, aerospace, aviation, sports, and automotive engineering. They have appealing properties such as high strength to weight ratio, good mechanical and electrical properties, and durability. Multilayered composites are prepared by stacking different layers of composites along different directions. This research focuses on the compression and tension response of multilayered composite panels without interference of bending by using in-plane loading. The aim of this research is to develop a generalized MATLAB code for a number of layers, to solve a model composite through analytical and MATLAB computations, to analyze the stress behavior in ANSYS (ACP) and finally to compare the results. For carrying out the analysis, a multi-layered, symmetric composite panel is modelled under in-plane loading. First, a mathematical model is formulized to solve the multi-layered composite panel under in-plane loading and analytical results are obtained. Next, a generic MATLAB code is developed, followed by simulations and computational study using ANSYS (ACP) module. The results of MATLAB and the solution of the mathematical model are found to be identical. Further, the results obtained from ANSYS (ACP) have shown the stresses in each layer and overall deformation of the composite panel. The overall results from three methods have shown that the stresses produced in a composite panel are symmetric across mirrored layers. However, there is a significant difference between the analytical and ANSYS (ACP) results, this is due to the limitations of the Classical Laminate Theory (CLT) which has been used in the analytical study. CLT does not take into effect the out-of-plane stresses. However, in real life scenarios, out-of-plane stresses exist under the in-plane loadings and have a significant effect around the edges and corners of the panel. If 10 percent of the edges are removed on both sides, the analytical results and simulations are found to be in good agreement. Further, after the ANSYS (ACP) analysis has been obtained for the panel, a sandwiched composite panel has been modelled by adding a core material of foam and polyethylene at the center of the composite. The thickness of the core material is varied to observe the change in the stress behavior. The results have shown that there is an increased stress behavior when a softer core is used or the thickness of the core material is increased.

Fluid Coupled Structural Analysis and Optimization of Expanded Polystyrene-Fiber-Reinforced Composite Wing of an Unmanned Aerial Vehicle

Structure Designation and Dynamic Model Analysis of Folding Wing for Underwater Vehicles

A Road Map to the Structural Optimization of a Type-C Composite UAV

Design and Analysis of UAV Propeller for Composite Materials

Structural integrity assessment and optimization of control surfaces in coaxial unmanned aerial vehicles: A case study of a micro coaxial UAV

Performance analysis of composite laminates wing skin with the aid of fluid structure interaction of aerodynamic loading-structural analysis

Synthesis and Characterization of Composite Materials with Enhanced Thermo-Mechanical Properties for Unmanned Aerial Vehicles (Uavs) and Aerospace Technologies

Efficient structural optimisation of composite materials aircraft wings

Low-cost development of a fully composite fixed-wing hybrid VTOL UAV

Static Aeroelastic Optimization of High-Aspect-Ratio Composite Aircraft Wings via Surrogate Modeling

Aerodynamic Analysis and Simulation for a Z-Shaped Folding Wing UAV

Design and analysis of an Eight Rotor Co-Axial UAV using carbon fiber composites

Determination of Acceptable Ranges of Asymmetric Manufacturing Tolerances based on Structural Analysis for a Drone Wing

Structural Design and Analysis for High Altitude Long Endurance UAV

Topology optimization of UAV structure based on homogenization of honeycomb core

Coupled Flexible and Flight Dynamics Modeling and Simulation of a Full-Wing Solar-Powered Unmanned Aerial Vehicle

Analysis and Experimental Study for Fatigue Performance of Wing-Fuselage Connection Structure for Unmanned Aerial Vehicle

Multiobjective optimization of the LASER aircraft wing’s composite structural design

NUMERICAL SIMULATIONOF FLEXIBLE WINGOF HALE UAV USING TWO-WAY FLUID STRUCTURE INTERACTION METHOD

An Optimum Design of a Subsonic Aircraft Wing due to the Aerodynamic Loading

Design and Analysis of Multi-Layered Composite Panels for In-Plane Loadings