Abstract:In this study, a multi-objective design optimization of a bow thruster, which involved both experimental and numerical analyses, was performed. By changing the chamfer form at the tunnel opening of the bow thruster and the position of the anti-suction tunnel, the optimization procedure aimed to improve the propulsion efficiency, reduce the amplitude of the fluctuating pressure on the tunnel wall, and balance the pressure difference on the hull caused by the speed. First, model tests were conducted to measure the thrust and torque of the bow thruster as well as the fluctuating pressure acting on the tunnel. Numerical simulations were also performed under the same conditions based on the unsteady Reynolds-averaged Navier-Stokes (URANS) method. The accuracy of the numerical results was verified by comparison with the experimental data. Second, the chamfer depth and angle of the tunnel opening and the distance between the anti-suction tunnel and the propeller axis in the length and height directions were taken as the design variables. A sample set that contained 30 sampling points was selected using the optimal Latin hypercube sampling (opt-LHS) method. A surrogate model was built based on the Support Vector Regression (SVR) algorithm, and the multi-island genetic algorithm was utilized during the tuning process of the surrogate model parameters. On this basis, the non-dominated sorting genetic algorithm II (NSGAII) was used for the three-objective optimization and the Pareto solution set was obtained. Due to the inverse relationship between the propulsion efficiency and the fluctuating pressure amplitude, four optimal solutions were selected from the Pareto optimal solution set, and direct numerical computations were conducted to verify the optimization results. The results showed that, compared with the original shape, the fluctuating pressure amplitudes for the four optimal solutions were reduced significantly after the optimization, with a maximum reduction of 18.56%, but their propeller propulsion efficiencies were slightly lower than the original hull. Increasing the chamfer angle and depth significantly reduced the flow-separation area around the tunnel entrance, but it correspondingly increased the flow velocity in the tunnel, which caused the propeller to not work at its highest efficiency point; thus, the propulsion efficiency was reduced to a certain extent. Moreover, the position of the anti-suction tunnel could be determined using the SBD method, but with an increase in the chamfer angle, the location where the jet of the bow thruster re-attached to the hull after mixing with the external flow moved towards the stern. This led to an expansion of the low-pressure area near the rear of the tunnel that correspondingly increased the pressure difference on the hull. If the chamfer angle was large enough, although the pressure difference could be reduced to a fairly low value through the anti-suction tunnel, it could not be balanced completely.

Design Optimization of the Lines of the Bulbous Bow of a Hull Based on Parametric Modeling and Computational Fluid Dynamics Calculation

Comparative investigations on hull line optimization based on traditional and fully parametric methods for saving energy

Ship Optimization Based on Fully-Parametric Models for Hull, Propeller and Rudder

CFD-based hull optimization in calm water using adaptive grid deformation method

Data-driven parameterization refinement for the structural optimization of cruise ship hulls

Hydrodynamic Decomposition-Based Optimization of Ship’s Hull–Propeller System Under Multiple Operating Conditions

Multi-objective optimization of a bow thruster based on URANS numerical simulations

Aerodynamic optimization of a luxury cruise ship based on a many-objective optimization system

Shape optimization design of a heaving buoy of wave energy converter based on fully parametric modeling and CFD method

Hull form optimization research based on multi‐precision back‐propagation neural network approximation model

A pointwise weighting prediction variance–high-dimensional model representation model-based global optimization approach for ship hull parametric design

Application of a variable-fidelity hydrodynamic optimization strategy in fuel-efficient ship design

Multi-objective Optimization of Ship Stern under Static and Seismic Loading

Research on the construction of multi objective coupling model and optimization method of ship form

Research progress on intelligent optimization techniques for energy-efficient design of ship hull forms

Practical ship afterbody optimization by multifidelity techniques

A Mesh Deformation Method for CFD-Based Hull form Optimization

Experimental Study and Numerical Simulation of the Water Entry of a Ship-Like Symmetry Section with an Obvious Bulbous Bow

Many-objective optimization for a deep-sea aquaculture vessel based on an improved RBF neural network surrogate model

Study of a hull form optimization system based on a Gaussian process regression algorithm and an adaptive sampling strategy, Part II: Multi-objective optimization

The Effect of Hull Form Parameters on the Hydrodynamic Performance of a Bulk Carrier