Abstract:Combustion system development in power generation is discussed ranging from the pre-environmental era in which the objectives were complete combustion with a minimum of excess air and the capability of scale up to increased boiler unit performances, through the environmental era (1970–), in which reduction of combustion generated pollution was gaining increasing importance, to the present and near future in which a combination of clean combustion and high thermodynamic efficiency is considered to be necessary to satisfy demands for CO2 emissions mitigation.From the 1970s on, attention has increasingly turned towards emission control technologies for the reduction of oxides of nitrogen and sulfur, the so-called acid rain precursors. By a better understanding of the NOx formation and destruction mechanisms in flames, it has become possible to reduce significantly their emissions via combustion process modifications, e.g. by maintaining sequentially fuel-rich and fuel-lean combustion zones in a burner flame or in the combustion chamber, or by injecting a hydrocarbon rich fuel into the NOx bearing combustion products of a primary fuel such as coal.Sulfur capture in the combustion process proved to be more difficult because calcium sulfate, the reaction product of SO2 and additive lime, is unstable at the high temperature of pulverized coal combustion. It is possible to retain sulfur by the application of fluidized combustion in which coal burns at much reduced combustion temperatures. Fluidized bed combustion is, however, primarily intended for the utilization of low grade, low volatile coals in smaller capacity units, which leaves the task of sulfur capture for the majority of coal fired boilers to flue gas desulfurization.During the last decade, several new factors emerged which influenced the development of combustion for power generation. CO2 emission control is gaining increasing acceptance as a result of the international greenhouse gas debate. This is adding the task of raising the thermodynamic efficiency of the power generating cycle to the existing demands for reduced pollutant emission. Reassessments of the long-term availability of natural gas, and the development of low NOx and highly efficient gas turbine–steam combined cycles made this mode of power generation greatly attractive also for base load operation.However, the real prize and challenge of power generation R&D remains to be the development of highly efficient and clean coal-fired systems. The most promising of these include pulverized coal combustion in a supercritical steam boiler, pressurized fluid bed combustion without or with topping combustion, air heater gas turbine-steam combined cycle, and integrated gasification combined cycle. In the longer term, catalytic combustion in gas turbines and coal gasification-fuel cell systems hold out promise for even lower emissions and higher thermodynamic cycle efficiency. The present state of these advanced power-generating cycles together with their potential for application in the near future is discussed, and the key role of combustion science and technology as a guide in their continuing development highlighted.

Biomass as a Renewable Energy Source for Power Boilers

The combustion of torrefied biomass in commercial-scale domestic boilers

Flue Gas Recirculation System for Biomass Heating Boilers—Research and Technical Applications for Reductions in Nitrogen Oxides (NOx) Emissions

Emission Factors for Biofuels and Coal Combustion in a Domestic Boiler of 18 kW

Emission of Harmful Substances from the Combustion of Wood Pellets in a Low-Temperature Burner with Air Gradation: Research and Analysis of a Technical Problem

The Return of Coal-Fired Combined Heat and Power Plants: Feasibility and Environmental Assessment in the Case of Conversion to Another Fuel or Modernizing an Exhaust System

Biomass Combustion in the Helically Coiled Domestic Boiler Combined with the Equilibrium/Chemical Kinetics CFD Approach

Combustion Efficiency of Various Forms of Solid Biofuels in Terms of Changes in the Method of Fuel Feeding into the Combustion Chamber

Study of Ash Sintering Temperature and Ash Deposition Behavior during Co-Firing of Polish Bituminous Coal with Barley Straw Using Non-Standard Tests

Improving the Fuel Combustion Quality Control System in Medium Power Boilers

Investigation of Biomass, RDF and Coal Ash-Related Problems: Impact on Metallic Heat Exchanger Surfaces of Boilers

Nitrogen Oxides Emission Reduction using Sewage Sludge Gasification Gas Reburning Process / Obniżenie Emisji Tlenków Azotu Przy Użyciu Procesu Reburningu Gazem Ze Zgazowania Osadów Ściekowych

Advanced CFD modelling of air and recycled flue gas staging in a waste wood-fired grate boiler for higher combustion efficiency and greater environmental benefits

CFD simulation study of a biomass pellet-fuelled boiler

Advances in Biomass Co-Combustion with Fossil Fuels in the European Context: A Review

A case study of biomass co-firing in a 55 MW pulverized coal fired furnace

Numerical Optimization on Char Conversion and NOx Emission under Various Operating Conditions in a Retrofit Biomass Boiler

Combustion technology developments in power generation in response to environmental challenges

Comparison of Emission Characteristics of Small-Scale Heating Systems Using Biomass Instead of Coal

Hybrid modeling of a circulating fluidized bed boiler for development of a prediction and prescription system for power plant operation

Numerical simulation of biomass high-ratioco-firing in a pre-pyrolysis pulverized coal industrial boiler