Abstract:Pile composite foundations (PCFs) have been commonly applied in reinforcement engineering to adjust the vertical stiffness of foundations, due to the displacement control design criteria for foundations. PCFs that have dissimilar pile lengths, located over inclined bedrock, have shown significantly different vertical behaviors from PCFs with equal pile lengths, placed over a semi-infinite medium. However, the vertical behaviors of dissimilar PCFs over inclined bedrock cannot be predicted with the current theoretical methods, although they have been widely adopted in engineering. An analytical method is proposed in this investigation to analyze the vertical bearing characteristics of dissimilar PCFs over inclined bedrock. A pile–soil system is decomposed into fictitious piles and extended soil, and then a control equation to determine the axial force along the fictitious piles is established, stemming from the compatibility conditions between them. The vertical behaviors of dissimilar PCFs can be obtained by solving the control equation with iterative procedures, and the equation is verified by two field load tests of single piles from the Honghe bridge and a numerical case. Then, the settlement and load transfer behaviors of 3 × 1 dissimilar PCFs and their influence factors are analyzed, and the results are as follows. (1) Obvious differences can be observed concerning the axial force distribution, settlement w, and load-sharing ratio (LSR) of each pile element for different pile–soil stiffness ratios (Ep/Es). (2) The LSR of pile 1 increases from 0.074 to 0.253 for the rigid pile and from 0.062 to 0.161 for the flexible pile condition when the cushion stiffness Kc changes from 1 × 104 kN/m to 3 × 108 kN/m. The non-dimensional vertical stiffness of the foundation, N0/wdEs, increases from 10.21 to 28.95 for the rigid pile condition and increases from 8.69 to 14.44 for the flexible pile condition, when Kc increases from 1 × 104 kN/m to 4 × 105 kN/m. (3) The neutral layer depth of the pile zn, the average settlement w, and the differential settlement wd of each element head decrease with Kc, and no negative friction zone exists (zn = 0 m) for all the pile elements when Kc > 2 × 105 kN/m. (4) The N0/wdEs decreases with the distance between the pile bottom and the inclined bedrock Δ. For the rigid and flexible pile conditions, the N0/wdEs is 22.16 and 13.48 for Δ = 1 m, and 13.13 and 10.10 for Δ = 8 m. The wd reaches 16.7 mm and 4.0 mm for Δ = 1 m and Δ = 8 m, respectively. (5) The N0/wdEs increases almost linearly with an increase in l/d for the rigid pile condition, and it gradually decreases for the flexible pile condition. The developed model can improve the design and analysis of PCFs located over inclined bedrock under vertical loading.

Vertical Load Transfer for Bored Piles Buried in Cohesive Intermediate Geomaterials

Analytical Elastoplastic Solutions of Laterally Loaded Long Piles

Model Tests on the Bearing Capacity of Precast Open-Ended Micro Pipe Piles in Soft Soil

A Simplified Planar Model for Geosynthetics Reinforced Composite Foundation Subjected to Vertical Load

Centrifuge Modelling of Lateral Loading Behaviour of a “Semi-Rigid” Mono-pile in Soft Clay

Model Test Study of Bearing Behavior of Small Prefabricated Piles in Soft Soil Area

Model Tests on Elevated Piles Subjected to Lateral Static and Impact Loading

Model tests on the bearing capacity of precast oxen-ended micro pipe plies in sort soil

Influence Of Excavation Unloading On Vertical Bearing Behavior Of Existing Pile Groups

Analysis of Axial Load-Transfer of Large-Diameter Cast-in-situ Tubular Pile

A Simplified Nonlinear Calculation Method to Describe the Settlement of Pre-Bored Grouting Planted Nodular Piles

On Vertical Dynamic Stability and Cross‐section Optimization of Closed‐ended Hollow Pile by Considering Soil Compaction Effects

The Vertical Behaviors of Dissimilar Pile Composite Foundations over Inclined Bedrock

Simplified Deformation Analyses of a Single Pile Subjected to Different Deformation Modes of the Pit Enclosure Structure

Sand-Steel Interface Behaviour Under Large-Displacement And Cyclic Shear

Solution of the Ultimate Bearing Capacity at the Tip of a Pile in Inclined Rocks Based on the Hoek-Brown Criterion

Model Test on Load Transfer Mechanism of a Static Drill Rooted Nodular Pile

Study on Axial Bearing Properties of Cast-in-place Concrete Thin-Wall Tubular Piles

Analysis of vertically loaded jet-grout-pile-strengthened piles of expanded cross-section

Solution of the Ultimate Bearing Capacity at the Tip of a Pile in Anisotropic Discontinuous Rock Mass Based on the Hoek–Brown Criterion

Load transfer of the disconnected pile