Abstract:This work involves the machinability investigation to study the effect of pulse on duration, pulse peak current, duty factor, and gap voltage to investigate the material removal mechanism for achieving machining stability along with improved dimensional accuracy. Findings have inferred that peak current and gap voltage were found to be significant for radial over‐cut, contributing 47.27% and 40.25%, respectively. The gap voltage was also shown to be notable for electrode wear rate and material removal rate, with contribution percentages of 43.59% and 20.11%, respectively. As a result, Vg was identified as the most influential variable in this study. This machinability study imparts a significant potential to improve the dimensional accuracy and productivity for aerospace applications. The industry is looking forward to technological advancements for productivity improvement, and this can be achieved by improving the machining performance concerned with the machinability challenges. The machinability investigation of carbon nanotubes/carbon fiber (CNTs/CF) reinforced composites is emerging with a strong application potential in the aviation industry because of their high strength and lightweight nature. However, the conventional machining practices pose a major challenge of excessive tool wear and dimensional accuracy which lead to a high production cost. Electric discharge machining is considered one of the possible solutions to treat with hard to machine materials like CNT/CF. Therefore, this work involves the machinability investigation to study the effect of pulse on duration, pulse peak current, duty factor, and gap voltage to investigate the material removal mechanism for achieving machining stability along with improved dimensional accuracy. Experiments were designed using Taguchi design followed by the analysis of variance, parametric effects, along with signal to noise ratio‐based multi‐response optimization. Findings have inferred that peak current and gap voltage were found to be significant for radial over‐cut, contributing 47.27% and 40.25%, respectively. The gap voltage was also shown to be notable for electrode wear rate and material removal rate, with contribution percentages of 43.59% and 20.11%, respectively. As a result, Vg was identified as the most influential variable in this study. This machinability study imparts a significant potential to improve the dimensional accuracy and productivity for aerospace applications.

Analyzing the dimensional errors in wire electric discharge machining of squeeze casted Al2024/Al 2 O 3 /W composite using cryogenic treated electrodes

Curved Profiles Machining of Ti6Al4V Alloy Through WEDM: Investigations on Geometrical Errors

Complex taper profile machining of WC-Co composite using wire electric discharge process: analysis of geometrical accuracy, cutting rate, and surface quality

Analysis of Wire-cut Electric Discharge Machining Behaviour of AA6061 / C / ZrO2 Hybrid Nano Composites using Taguchi's method

Wire EDM machining characteristics of squeeze cast Al-Zn-Mg-Cu/(SiC + Al2O3) hybrid composite by TOPSIS approach

Analysis and Optimization of the Machining Characteristics of High-Volume Content SiCp/Al Composite in Wire Electrical Discharge Machining

Experimental Study on Parametric Effect of Wire Electric Discharge Machining of Titanium Grade 2 Alloy Using Cryogenic Treated Wire

Machinability investigation in electric discharge machining of carbon fiber reinforced composites for aerospace applications

Process parameters optimization and performance analysis of micro-complex geometry machining on Ti6Al4V

Effect of Al7075 and Activated Carbon reinforced Composite on Optimizing WEDM Responses

Experimental Investigations and Optimum Performance Evaluation of Wire-EDM Characteristics of Aluminium 6061-Magnesite Composites

Evaluation of Wire Electrical Discharge Machining Performance Features on EN AW-6082 T6 Aluminum Alloy and Optimization of Machining Characteristics

Investigation of aluminum alloy 6061 in Wire-EDM regarding surface roughness and material removal rate by adopting optimization techniques

Optimizing dimensional accuracy of titanium alloy features produced by wire electrical discharge machining

WEDM of Al/SiC/Ti composite: A Hybrid Approach of RSM-ARAS-TLBO Algorithm

Synthesis and Characterization of Mechanical Properties and Wire Cut EDM Process Parameters Analysis in AZ61 Magnesium Alloy + B4C + SiC

Optimization and Microstructural Studies on the Machining of Inconel 600 in WEDM Using Untreated and Cryogenically Treated Zinc Electrodes

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

Investigation of Machining Rate and Surface Roughness in Wire EDM of Al6063/WC/ZrO2 Composite using Response Surface Methodology

Performance Analysis of Wire Electrodes on Machining Ti-6Al-4V Alloy using Electrical Discharge Machining Process

Machining characteristics of 65 vol.% SiCp/Al composite in micro-WEDM