Abstract:Journal of Composite Materials, Ahead of Print. This study presents an investigation into mechanical and thermal properties, as well as the microstructure of Automated Fiber Placement-manufactured laminates using a novel carbon fiber-reinforced low-melt polyaryl ether ketone polymer material. The material's lower melting temperature and lower melt viscosity as compared to established high-temperature thermoplastic materials as PEEK, promises favourable characteristics for the Automated Fiber Placement process. This work aims at in-situ consolidation and the influence of a heated tooling and a post process tempering step, which both turned out to be promising in previous investigations. Laminates were manufactured using a cold tooling, a heated tooling configuration, a cold tooling with a subsequent tempering process step and a hot-pressed reference laminate. Differential Scanning Calorimetry showed that crystallinity values more than doubled for the heated tooling and post process tempering configurations, compared to the cold tooling, reaching 24% and 30%, respectively. Mechanical strength values showed an increase in interlaminar shear strength and compression strength but did not increase to the same extent as was expected from the increase in crystallinity. With Scanning Electron Microscopy differences in the microscopic structure of the polymer matrix could be detected. While the post process tempering step leads to a mostly lamellar crystalline structure, the heated tooling configuration and the post process hot pressing induce a predominance of crystalline spherulites, which might positively affect the mechanical performance. Computed Tomography scans revealed a high amount of porosity in the in-situ-manufactured samples and unprocessed tape material, which likely mitigated the positive effect of increased crystallinity.

Mechanical and thermal characterization of additively manufactured novel multilayer polymer composite through experiments and finite element simulation

An innovative multilayered material fabricated through additive manufacturing for structural applications: method and mechanical properties

Additive Manufacturing of Composite Polymers: Thermomechanical FEA and Experimental Study

Mechanical characteristics and failure morphology of FFF-printed poly lactic acid composites reinforced with carbon fibre, graphene and MWCNTs

Mechanical Properties and Assessment of PLA Mixed with Carbon by Using Additive Manufacturing

Digital Multiphase Composites via Additive Manufacturing

Preparation and Evaluation of the Tensile Characteristics of Carbon Fiber Rod Reinforced 3D Printed Thermoplastic Composites

Effect of Fused Filament Fabrication Parameters and Tetrabromobisphenol-A/Microcrystalline Cellulose Additives on the Dynamic Mechanical Behavior of Polycarbonate/Acrylonitrile–Butadiene–Styrene Blends for Precision Structures

Experimental Investigation of the Structural Performance of Composite Structures Produced using Additive Manufacturing

Mechanical Properties and Characterization of Polylactic Acid/Carbon Fiber Composite Fabricated by Fused Deposition Modeling

Compressive Properties of Additively Manufactured Metal-Reinforced PLA and ABS Composites

Investigation into Thermomechanical Response of Polymer Composite Materials Produced through Additive Manufacturing Technologies

Mechanical properties of additively manufactured polymeric composites using sheet lamination technique and fused deposition modeling: A review

Additive manufacturing of mechanical testing samples based on virgin poly (lactic acid) (PLA) and PLA/wood fibre composites

An Investigation into Mechanical Properties of 3D Printed Thermoplastic-Thermoset Mixed-Matrix Composites: Synergistic Effects of Thermoplastic Skeletal Lattice Geometries and Thermoset Properties

Characteristics of in-situ automated fiber placement carbon-fiber-reinforced low-melt polyaryl ether ketone laminates part 1: Manufacturing influences

Investigation of LCD 3D Printing of Carbon Fiber Composites by Utilising Central Composite Design

Technology and mechanical properties of reinforced continuous fiber 3D-printed thermoplastic composite

Additive manufacturing and mechanical analysis of multi-material polymer parts combining thermosets and thermoplastics

The fabrication of long carbon fiber reinforced polylactic acid composites via fused deposition modelling: Experimental analysis and machine learning

Integrated computational modeling of large format additive manufacturing: Developing a digital twin for material extrusion with carbon fiber-reinforced acrylonitrile butadiene styrene