Abstract:Multi-mechanism coupled electroplasticity (EP) has not been fully elucidated yet due to the difficulty in eliminating thermal effect, although isothermal, air-cooled, and cryogenic methods are usually used, there are different heating histories from electrically-assisted deformation. The 0–7% pre-strained Ti–6Al–4V alloy is taken as the case material. Based on the two different characteristics of the time-accumulation of thermal effect and the instantaneous nature of the athermal effect, a comparative study is conducted by designing two temporal coordination methods of pulse current and straining, viz., asynchronous loading with high-energy current (ALHC) and synchronous loading with low-energy current (SLLC), where the thermal and athermal effects are highlighted by different loading times, loading and unloading moments of pulse current of different magnitudes. Under ALHC condition, the decreasing yield strength and increasing elongation of the 7% pre-deformed material are observed with increasing current density and loading times, and stress reduction up to 20.7% for yield strength and ductility recovery of maximal 99.1% for elongation are obtained for 14.0 A/mm 2 and loading three times. Moreover, stage B of the work hardening rate related to dislocation de-pinning disappears, and the TEM shows an annealing effect that the tangled dislocations are annihilated and rearranged by climbing. Thus, the Joule heat-based thermal effect dominates this condition. Under SLLC condition, the loading and unloading of pulse current of 2.81 A/mm 2 in the plastic stage result in an instantaneous drop and rebound in flow stress and work hardening rate (stage B exists), respectively, and are accompanied by the negligible instantaneous temperature rise, while loading at the elastic stage, the overall flow stress and work hardening rate is decreased. It is concluded that the athermal effect can lower the dislocation phonon drag effect and the deformation activation energy, and change the athermal atomic state and dislocation slip mode, which dominates the varied flow stress and elongation. A dislocation dynamics-based physical model is developed by taking into account phonon drag, diffusion activation energy, and deformation activation energy to account for the thermal and athermal effects on dislocations, providing a self-consistent explanation of the above behaviors and mechanisms of the flow stress and ductility under ALHC and SLLC conditions.

Deformation behavior of steel sheets under dynamic underwater impact: electric-pulse triggered energetic materials loading vs. wire explosion loading

Experimental and Numerical Simulations of ELM-like Transient Damage Behaviors to Different Grade Tungsten and Tungsten Alloys

Influence of wire parameters on the formability of DP600 steel sheets during wire explosion impact forming

Microstructure Evolution and Deformation Mechanism of Tantalum-Tungsten Alloy Liner under Ultra-High Strain Rate by Explosive Detonation

Dynamic failure behavior of steel wire mesh subjected to medium velocity impact: Experiments and simulations

Deformation Mechanism of 5052 Aluminum Alloy Using Electrically Assisted Electromagnetic Forming

Dynamic Response and Numerical Interpretation of Three Kinds of Metals for EFP Liner under Explosive Loading

Plastic Deformation of Metal Tubes Subjected to Lateral Blast Loads

On the mechanical behaviour of steel wire mesh subjected to low-velocity impact

Design and Identification of High Performance Steel Alloys for Structures Subjected to Underwater Impulsive Loading

Deformation behaviors and microstructure evolution of Ti6321 alloy under air blast loadings

Influence of Pulsed Electric Current on the Motion of Spontaneous Plastic-Deformation Waves in Steel-Plate Extension

Antisymmetric deformation behavior during eccentric explosion electro-hydraulic sheet forming process

Toughening and Hardening Limited Zone of High-Strength Steel through Geometrically Necessary Dislocation When Exposed to Electropulsing

High deformation and delamination mechanisms explained through mesoscale and nanoscale phenomena in pearlitic steel wires

Thermal and Electromigration Effects of Electropulsing on Dynamic Recrystallization in Mg–3Al–1Zn Alloy

Mechanical properties and microstructure evolution of 2219 aluminum alloy via electromagnetic ring expansion & electromagnetic treatment

Experimental study on the mechanical properties and impact behaviors of entangled metallic wire material under repeated low-velocity impacts

Dynamic Strength Estimates for a High-Strength Experimental Steel

Decoupling electroplasticity by temporal coordination design of pulse current loading and straining

Dynamic tensile properties and microstructural evolution of extruded EW75 magnesium alloy at high strain rates