Abstract:This study focuses on the development of a piezoelectric device capable of generating feedback vibrations to the user who manipulates it. The objective here is to explore the possibility of developing a haptic system that can replace physical buttons on the tactile screen of in-car systems. The interaction between the user and the developed device allows completing the feedback loop, where the user's action generates an input signal that is translated and outputted by the device, and then detected and interpreted by the user's haptic sensors and brain. An FEM (finite element model) via ANSYS multiphysics software was implemented to optimize the haptic performance of the wafer structure consisting of a BaTiO3 multilayered piezocomposite coated on a PET transparent flexible substrate. Several parameters relating to the geometric and mechanical properties of the wafer, together with those of the electrodes, are demonstrated to have significant impact on the actuation ability of the haptic device. To achieve the desired vibration effect on the human skin, the haptic system must be able to drive displacement beyond the detection threshold (~2 µm) at a frequency range of 100-700 Hz. The most optimized actuation ability is obtained when the ratio of the dimension (radius and thickness) between the piezoelectric coating and the substrate layer is equal to ~0.6. Regarding the simulation results, it is revealed that the presence of the conductive electrodes provokes a decrease in the displacement by approximately 25-30%, as the wafer structure becomes stiffer. To ensure the minimum displacement generated by the haptic device above 2 µm, the piezoelectric coating is screen-printed by two stacked layers, electrically connected in parallel. This architecture is expected to boost the displacement amplitude under the same electric field (denoted E) subjected to the single-layered coating. Accordingly, multilayered design seems to be a good alternative to enhance the haptic performance while keeping moderate values of E so as to prevent any undesired electrical breakdown of the coating. Practical characterizations confirmed that E=20 V/μm is sufficient to generate feedback vibrations (under a maximum input load of 5 N) perceived by the fingertip. This result confirms the reliability of the proposed haptic device, despite discrepancies between the predicted theory and the real measurements. Lastly, a demonstrator comprising piezoelectric buttons together with electronic command and conditioning circuits are successfully developed, offering an efficient way to create multiple sensations for the user. On the basis of empirical data acquired from several trials conducted on 20 subjects, statistical analyses together with relevant numerical indicators were implemented to better assess the performance of the developed haptic device.

In-silico user study case: wearable feedback haptic device for rehabilitation

Preliminary Study on Piezoresistive and Piezoelectric Properties of a Double-Layer Soft Material for Tactile Sensing

Haptic Feedback Device Using 3D-Printed Flexible, Multilayered Piezoelectric Coating for In-Car Touchscreen Interface

Encapsulation of Piezoelectric Transducers for Sensory Augmentation and Substitution with Wearable Haptic Devices

A Novel Silicon Based Tactile Sensor On Elastic Steel Sheet For Prosthetic Hand

A 3D-Printed Soft Haptic Device with Built-in Force Sensing Delivering Bio-Mimicked Feedback

Integrated Soft Sensors and Elastomeric Actuators for Tactile Machines with Kinesthetic Sense

SensoPatch: A Reconfigurable Haptic Feedback with High-Density Tactile Sensing Glove

Electroactive Elastomeric Haptic Displays of Organ Motility and Tissue Compliance for Medical Training and Surgical Force Feedback

Soft Wearable Skin-Stretch Device for Haptic Feedback using Twisted and Coiled Polymer Actuators.

A Wearable Soft Haptic Communicator Based on Dielectric Elastomer Actuators.

VIBES: Vibro-Inertial Bionic Enhancement System in a Prosthetic Socket

Exploring Biomimetic Stiffness Modulation and Wearable Finger Haptics for Improving Myoelectric Control of Virtual Hand

Self‐Powered, Soft and Breathable Human–Machine Interface Based on Piezoelectric Sensors

Biosymbiotic haptic feedback - Sustained long term human machine interfaces

A low voltage-powered soft electromechanical stimulation patch for haptics feedback in human-machine interfaces

Attention Enhancement for Exoskeleton-Assisted Hand Rehabilitation Using Fingertip Haptic Stimulation

Utilizing Computational Modeling to Aid the Development of a Wearable Soft Robot for Finger Rehabilitation

A Flexible Piezoelectret Actuator/Sensor Patch for Mechanical Human-Machine Interfaces

Design and Characterisation of Multi-cavity, Fluidic Haptic Feedback System for Mechano-tactile Feedback

Silicon-Based Piezoresistive Stress Sensor Arrays for Use in Flexible Tactile Skin