STUDY OF SEVEN-BEND ACHROMAT LATTICES WITH INTERLEAVED DISPERSION BUMPS FOR HALS
Zhenghe Bai,Wei Li,Gangwen Liu,Lin Wang,Derong Xu,Tong Zhang
DOI: https://doi.org/10.18429/jacow-ipac2019-tupgw040
2019-01-01
Abstract:Previously, we proposed a multi-bend achromat (MBA) lattice concept, called the MBA with interleaved dispersion bumps, which was then used to design a 7BA lattice for the Hefei Advanced Light Source (HALS) storage ring. Recently, such a 7BA lattice was further designed and optimized for the HALS by changing the number of lattice cells, scanning working point and employing octupoles. And two new HALS designs with such 7BA lattices have been made, one with 30 lattice cells and a natural emittance of 25 pm·rad and the other with 28 cells and 33 pm·rad. They had much better nonlinear dynamics performances than the previous design. The detailed study for these two HALS lattices will be presented in this paper. INTRODUCTION Hefei Advanced Light Source (HALS) [1] will be a soft X-ray diffraction-limited storage ring with an emittance of tens of pm·rad at 2.4 GeV. The R&D for the HALS is ongoing. To achieve better nonlinear dynamics performance at such an ultra-low emittance, several multi-bend achromat (MBA) lattice concepts have been proposed and studied for the HALS storage ring [2-5]. After a comparison of these lattice concepts, the MBA with interleaved dispersion bumps (IDB-MBA) [3] was chosen as the preferred option for the HALS. Figure 1 shows the schematic of the IDB-MBA lattice concept. In each lattice cell of the IDB-MBA, two pairs of interleaved dispersion bumps are created, and the phase advance between each pair of bumps satisfies the condition for cancellation of nonlinear effects induced by normal sextupoles. The IDB-MBA has one more pair of bumps than the hybrid MBA [6] so that more sextupoles can be accommodated, which is beneficial for enlarging dynamic momentum aperture (MA). Figure 1: Schematic of the IDB-MBA lattice concept. We have made a storage ring design with 32 IDB-7BA lattice cells for the HALS [4]. In this paper, some further studies on such an IDB-7BA lattice will be done for the HALS. By changing the number of lattice cells, scanning working point and employing octupoles, the ability of the IDB-7BA lattice will be further explored in the HALS lattice design. IDB-7BA LATTICE DESIGNS FOR HALS We will reduce the number of lattice cells from 32 [4] to 30 and 28 to study the IDB-7BA lattice for the HALS. HALS with 30 Lattice Cells We first present the storage ring design with 30 identical IDB-7BA lattice cells for the HALS. Figure 2 shows the magnet layout and linear optical functions of the designed IDB7BA lattice. The phase advances between each pair of dispersion bumps are about (1.5, 0.5)×2π. The first and last two bends, as well as the middle bend, are longitudinal gradient bends (LGBs) with the dipole field profiles shown in Fig. 3. The profile of the second LGB is non-symmetric. The middle LGB has a high dipole field of 2 T as the radiation source for bend beamlines. Note that there is no defocusing quadrupole close to the middle LGB. Besides, there are two reverse bends in the 2nd and 3rd dispersion bumps. Some main parameters of the designed storage ring are listed in Table 1. The natural emittance is 24.7 pm·rad. Figure 2: IDB-7BA lattice of the design with 30 cells. Table 1: Main Parameters of Two HALS Designs Parameters 30 cells 28 cells Energy (GeV) 2.4 Circumference (m) 672 Nat. emittance (pm·rad) 24.7 33.3 Tune vx 71.296 68.172 Tune vy 23.296 24.172 Nat. chromaticities -97, -110 -87, -121 Momentum compaction 5.0×10-5 6.6×10-5 Long straight length (m) 5.4 6.4 βx, y at long straights (m) 7.36, 3.63 5.59, 2.94 ___________________________________________ * baizhe@ustc.edu.cn † wanglin@ustc.edu.cn 10th Int. Particle Accelerator Conf. IPAC2019, Melbourne, Australia JACoW Publishing ISBN: 978-3-95450-208-0 doi:10.18429/JACoW-IPAC2019-TUPGW040 MC2: Photon Sources and Electron Accelerators A05 Synchrotron Radiation Facilities TUPGW04