Abstract:In internal combustion engines, cycle-to-cycle and cylinder-to-cylinder variations of the combustion process have been shown to negatively impact the fuel efficiency of the engine and lead to higher exhaust emissions. The combustion variations are generally tied to differences in the composition and condition of the trapped mass throughout each cycle and across individual cylinders. Thus, advanced engines featuring exhaust gas recirculation, flexible valve actuation systems, advanced fueling strategies, and turbocharging systems are prone to exhibit higher variations in the combustion process. In this study, the cylinder-to-cylinder variations of the combustion process in a dual-fuel internal combustion engine leveraging late intake valve closing are investigated and a model to predict and address one of the root causes for these variations across cylinders is developed. The study is conducted on an inline six-cylinder heavy-duty dual-fuel engine equipped with exhaust gas recirculation, a variable geometry turbocharger, and a fully flexible variable intake valve actuation system. The engine is operated with late intake valve closure timings in a dual-fuel combustion mode in which a high reactivity fuel is directly injected into the cylinders and a low reactivity fuel is port injected into the cylinders. The cylinder-to-cylinder variations observed in the study have been associated with the maldistribution of the port-injected fuel, which is exacerbated at late intake valve timings. The resulting difference in indicated mean effective pressure between the cylinders ranges from 9% at an intake valve closing of 570° after top dead center to 38% at an intake valve closing of 620° after top dead center and indicates an increasingly uneven fuel distribution. The study leverages both experimental and simulation studies to investigate the distribution of the port-injected fuel and its impact on cylinder-to-cylinder variation. The effects of intake valve closing as well as the impact of intake runner length on fuel distribution were quantitatively analyzed, and a model was developed that can be used to accurately predict the fuel distribution of the port-injected fuel at different operating conditions with an average estimation error of 1.5% in cylinder-specific fuel flow. A model-based control strategy is implemented to adjust the fueling at each port and shown to significantly reduce the cylinder-to-cylinder variations in fuel distribution.

Model-Based Unified Framework for Detection and Mitigation of Cyclic Torque Imbalance in a Gasoline Engine

A Control-Oriented Engine Torque Online Estimation Approach for Gasoline Engines Based on In-Cycle Crankshaft Speed Dynamics

Effective torque modeling of a gasoline-ethanol engine for multivariable adaptive control design

An Experimental Study on Engine Dynamics Model Based In-Cylinder Pressure Estimation

Design of Active Fault-Tolerant Control System for Air-Fuel Ratio control of Internal Combustion engine using nonlinear regression-based observer model

Minimization of Torque Deviation of Cylinder Deactivation Engine through 48V Mild-Hybrid Starter-Generator Control

Input Observer-Based Individual Cylinder Air-Fuel Ratio Control: Modelling, Design and Validation.

An Economic Nonlinear Model Predictive Control Strategy for SI Engines: Model-Based Design and Real-Time Experimental Validation

Modeling and control of fuel distribution in a dual-fuel internal combustion engine leveraging late intake valve closings

Sensor selection and controller design method with application to turbocharged stoichiometric spark-ignited engine controls with low pressure EGR

Model-Based Precise Air-Fuel Ratio Control for Gaseous Fueled Engines

Modeling and Control of Combustion Phasing in Dual-Fuel Compression Ignition Engines

Computationally efficient modeling of load dynamics in turbocharged internal combustion engines

Model Predictive Direct Torque Control and Fuzzy Logic Energy Management for Multi Power Source Electric Vehicles

MAP Learning and Disturbance Observation Based Engine Torque Control for Dynamometer Test Bench

Real-time misfire detection via sliding mode observer

Genetic algorithm based active fault-tolerant control system for air fuel ratio control of internal combustion engines

Actuator Fault-Tolerant Control for Aero-Engine Control System: A Zonotope-Based Approach

A comprehensive engine to drive-cycle modelling framework for the fuel economy assessment of advanced engine and combustion technologies

Research on Fuel Offset Control of High-Pressure Common-Rail Diesel Engine Based on Crankshaft Segment Signals

A Model-Predictive-Control-Based Torque Demand Control Approach for Parallel Hybrid Powertrains