Abstract:Model based process development using predictive mechanistic models is a powerful tool for in-silico downstream process development. It allows to obtain a thorough understanding of the process reducing experimental effort. While in pharma industry, mechanistic modeling becomes more common in the last years, it is rarely applied in food industry. This case study investigates risk ranking and possible optimization of the industrial process of purifying lactoferrin from bovine milk using SP Sepharose Big Beads with a resin particle diameter of 200 µm, based on a minimal number of lab-scale experiments combining traditional scale-down experiments with mechanistic modeling. Depending on the location and season, process water pH and the composition of raw milk can vary, posing a challenge for highly efficient process development. A predictive model based on the general rate model with steric mass action binding, extended for pH dependence, was calibrated to describe the elution behavior of lactoferrin and main impurities. The gained model was evaluated against changes in flow rate, step elution conditions, and higher loading and showed excellent agreement with the observed experimental data. The model was then used to investigate the critical process parameters, such as water pH, conductivity of elution steps, and flow rate, on process performance and purity. It was found that the elution behavior of lactoferrin is relatively consistent over the pH range of 5.5 to 7.6, while the elution behavior of the main impurities varies greatly with elution pH. As a result, a significant loss in lactoferrin is unavoidable to achieve desired purities at pH levels below pH 6.0. Optimal process parameters were identified to reduce water and salt consumption and increase purity, depending on water pH and raw milk composition. The optimal conductivity for impurity removal in a low conductivity elution step was found to be 43 mS/cm, while a conductivity of 95 mS/cm leads to the lowest overall salt usage during lactoferrin elution. Further increasing the conductivity during lactoferrin elution can only slightly lower the elution volume thus can also lead to higher total salt usage. Low flow rates during elution of 0.2 column volume per minute are beneficial compared to higher flow rates of 1 column volume per minute. The, on lab-scale, calibrated model allows predicting elution volume and impurity removal for large-scale experiments in a commercial plant processing over 106 liters of milk per day. The successful model extrapolation was possible without recalibration or detailed knowledge of the manufacturing plant. This study therefore provides a possible pathway for rapid process development of chromatographic purification in the food industries combining traditional scale-down experiments with mechanistic modeling.

Minimizing the environmental footprint in food production: A case study on the improvement of an industrial tank cleaning process through adaptive cleaning devices

A case study on artificial intelligence based cleaner production evaluation system for surface treatment facilities

Challenges in Cleaning: Recent Developments and Future Prospects

Biomimetic Leaves with Immobilized Catalase for Machine Learning-Enabled Validating Fresh Produce Sanitation Processes

Cleaning verification: A five parameter study of a Total Organic Carbon method development and validation for the cleaning assessment of residual detergents in manufacturing equipment

All Treatment Parameters Affect Environmental Surface Sanitation Efficacy, but Their Relative Importance Depends on the Microbial Target

Optimization of temperature for effective cleaning with a novel cleaning rig: Influence of soil and surface types

Microbubble-Assisted Cleaning To Enhance the Removal of Milk Deposits from the Heat Transfer Surface

Applied Cleaning Methods of Oil Residues from Industrial Tanks

Washing Effectiveness Assessment of Different Cleaners on a Small-Scale Multistage Compressor

Selection and Validation of Detergents and Surfactants for Aqueous Critical Cleaning

Multi-length Scale Approach to Investigate Cleaning of Food-Derived Deposits Adhered to Hard Surfaces: Mixtures of Starch, Whey Protein, and Lard

Microbubble-Assisted Cleaning-in-Place Process for Ultrafiltration System and Its Environmental Performance

Model based process optimization of an industrial chromatographic process for separation of lactoferrin from bovine milk

Energy saving based on minimization of water consumption in housing and communal services machines

AI-based tank truck cleaning robot

Individual training for farmers based on results from protein and ATP rapid tests and microbiological conventional cultural methods improves hygiene in pig fattening pens

Towards sustainable Cleaning-in-Place (CIP) in dairy processing: Exploring enzyme-based approaches to cleaning in the Cheese industry

Optimization and improving of the production capacity of a flexible tyre painting cell

Determination of the Feasibility of a Renewed Approach to the Mechanical Cleaning Stage in Wastewater Treatment Plant: A Laboratory Study