Abstract:To realize long-cherished dreams of employing inorganic graphene cousins such as boron nitride (BN) and molybdenum disulfide (MoS2) for large area coating applications, e.g., miniaturized electronic chips, radio wave devices, energy storage, LEDs, and solar cells, scalable synthesis pathways are presently being hunted with unprecedented curiosity to obtain large-scale 2D exfoliated sheets. Modified Hummers’ method provides an apt alternate and has already been established for graphene. However, it currently faces limitations in scalable production of BN and MoS2 as the nature of binding in their crystallographic lattice as well as their interactions with the solvents are different in these materials’ vis-a-vis graphene. Therefore, intensely focused efforts are needed to optimize synthesis parameters to produce scalable quantities of these advanced materials at an economical cost. By hybridizing BN with MoS2, for example, one can maneuver the material’s dielectric functionality, such as frequency bandwidth where it functions. In this report, we present a facile synthesis of BN and MoS2 via modified Hummers’ synthesis. While the fixed BN:KMnO4 precursor ratio of 1:6 was considered to obtain 2D BN, it (MoS2:KMnO4) was altered, i.e., 1:6, 1:5, and 1:4, for obtaining MoS2 sheets. Interestingly, while precursor ratio 1:6 resulted in average lateral dimension ~100 nm, precursor ratio of 1:4 yielded lateral dimensions ~500 nm as evidenced from TEM measurements. Solvothermal (200 °C for 2 h) reduction was carried out for both BN and MoS2 to remove the surface functionalities employing reducing solvent DMF. We obtained few-layer crystalline atomic sheets of BN and MoS2. While inter-atomic distance in 2D BN was measured to be ~1.5 A° as evident from HRTEM imaging, E2g vibration mode ~ 1360 cm−1 was recorded in Raman spectroscopy. While HRTEM imaging reveals that average inter-atomic (Mo-S) distances in MoS2 atomic sheets was obtained to be ~2.41 A°, two distinct MoS2 Raman modes, viz., E2g ~ 404 cm−1 and A1g ~385 cm−1, were witnessed. Microwave blending of 2D MoS2 with 2D BN resulted in significant modulation of dielectric behavior. While the modified Hummers’ synthesis for BN and MoS2 will be a boon in disguise for several dream applications envisaged earlier, it may inspire future generations of devices and sensors with novel functionalities, it is believed.

Detonation exfoliated mechanism of graphene-like MoS2 prepared by the intercalation-detonation method and promising exfoliation for 2D materials

Direct Chemical Vapor Deposition Growth and Band-Gap Characterization of MoS2/h-BN van der Waals Heterostructures on Au Foils

Edge Reconstruction-Dependent Growth Kinetics of MoS2

Exfoliation of Large-Flake, Few-Layer MoS2 Nanosheets Mediated by Carbon Nanotubes.

Oxidation layering mechanism of graphene-like MoS2 prepared by the intercalation-detonation method

X-ray Characterizations of Exfoliated MoS2 Produced by Microwave-Assisted Liquid-Phase Exfoliation

Electrochemically Exfoliating MoS 2 into Atomically Thin Planar‐Stacking Through a Selective Lateral Reaction Pathway

High-yield exfoliation of MoS2 (WS2) monolayers towards efficient photocatalytic hydrogen evolution

Highly efficient solution exfoliation of few-layer molybdenum disulfide nanosheets for photocatalytic hydrogen evolution

Molecular Simulation of MoS2 Exfoliation

Facile Preparation of Few-layer MoS2-NS by Liquid-Phase Ultrasonic Exfoliation

High-yield exfoliation of MoS2 nanosheets by a novel spray technique and the importance of soaking and surfactants

Chemical exfoliation synthesis of boron nitride and molybdenum disulfide 2D sheets via modified Hummers’ method

Engineering the Edges of MoS2 (WS2) Crystals for Direct Exfoliation into Monolayers in Polar Micromolecular Solvents

Improving electrocatalytic activity of 2H-MoS2 nanosheets obtained by liquid phase exfoliation: Covalent surface modification versus interlayer interaction

Solvent-assisted exfoliation for high-quality molybdenum disulfide nanoflakes and relevant field-effect transistors

Scalable and controllable synthesis of 2D high-proportion 1T-phase MoS2

From Bulk Molybdenum Disulfide (MoS2) to Suspensions of Exfoliated MoS2 in an Aqueous Medium and Their Applications

Exfoliation of MoS2 by zero-valent transition metal intercalation

Aggregation‐Induced Emission Luminogens for Direct Exfoliation of 2D Layered Materials in Ethanol

Modified Molten Salt Assisted Exfoliation of Large‐Size 2D Materials