Abstract:Objectives: Modern adhesives and composites allow the restoration of deep defects. In such cases, the matrix technique is particularly challenging, and excess composite is a common problem. Removing such overhangs with a scalpel has already been described as a substance preserving or selective finishing technique. Clinically, restoration margins may appear as a white line after scalpel finishing, and it is unclear whether this line represents a marginal gap and/or whether scalpel finishing promotes marginal gap formation. Therefore, the aim of this study was to investigate the influence of scalpel finishing of deep Class II composite restorations on marginal gap formation. Methods and materials: Standardized mesioocclusal-distal (MOD) cavities were prepared and restored in 60 human molars randomly divided into six finishing protocol groups: G1, scalpels (SC); G2, oscillating files (OF); G3, finishing strips (FS); G4, scalpels and finishing strips (SC+FS); G5, scalpels and polishing discs (SC+PD); G6, polishing discs alone (PD, controls). The groups were additionally assigned to finishing and polishing in a phantom head (groups 1-4) or hand-held setting (groups 5-6) to simulate clinical and in-vitro research conditions, respectively. After restoration, artificial aging was performed by thermocycling (5-55°C, 2500 cycles) and mechanical loading (50 newtons (N) with 500,000 cycles) prior to scanning electron microscopy analysis of proximal restoration margin quality on the mesial and distal surfaces (n=120) of each tooth. Outcomes (perfect margin, marginal gap, overhang, marginal fracture) were statistically analyzed by t-test, Mann-Whitney U test, single-factor analysis of variance, post-hoc t-test, Kruskal-Wallis test and Dunn-Bonferroni correction for multiple group comparisons. Cohen's effect size d(Cohen) was calculated to show the strength of the relationship between variables. Results: Overall, marginal quality was significantly better in the hand-held setting (SC+PD and PD) than the phantom head setting (SC, OF, FS, SC+FS). The best marginal quality was achieved with oscillating files in the phantom head setting and with scalpels plus polishing discs in the hand-held setting. Marginal gaps occurred significantly more often with scalpels, but the proportion of gaps was very low and clinically insignificant. Finishing strips were the least effective instruments for removing overhangs but performed better in combination with scalpels. Conclusions: Scalpel finishing can effectively and gently remove overhangs from enamel. However, blades should be used with caution as they can cut the dentin and cementum. Scalpel finishing does not lead to a clinically relevant increase in marginal gaps, but should be followed by polishing, whenever possible, to eliminate any marginal fractures that might be present.

Polishing methods for composites restoration: the influence on human gingival fibroblasts behaviour

Disparity in the Influence of Implant Provisional Materials on Human Gingival Fibroblasts with Different Phases of Cell Settlement: An In Vitro Study

Proteomic Analysis of Fibroblasts Exposed to Resin Composite Release

Surface Modification And Its Effect On Attachment, Spreading, And Proliferation Of Human Gingival Fibroblasts

The clinical efficacy of primary culture of human fibroblasts in gingival augmentation procedures-a preliminary report

The Effect of Different Finishing and Polishing Systems on Surface Properties of New Flowable Bulk-fill Resin Composite

Effect of Finishing Protocol on Obtaining and Maintaining Gloss in Four Nanohybrid Resin Composites

Effect of air-polishing on surface roughness of composite dental restorative material – comparison of three different air-polishing powders

Assessing the impact of dental restorative materials on fibroblast cells: an immunohistochemical and ELISA analysis

Influence of the Scalpel Finishing Technique on Marginal Gap Formation in Class II Resin Composite Restorations

Effect of finishing/polishing techniques and time on surface roughness of esthetic restorative materials

Antimicrobial Activity of Glycine Air Polishing: A Clinical Split- Mouth Study on Full-Arch Implant-Supported Rehabilitations

Effect of dental composite dust on human gingival keratinocytes

The effect of contemporary finishing and polishing systems on the surface roughness of bulk fill resin composite and nanocomposites

The Effect of Flowable Composite Resins on Periodontal Health, Cytokine Levels, and Immunoglobulins

Influence of Instrument Lubrication on Properties of Dental Composites

Gingival fibroblast response to (hybrid) ceramic implant reconstruction surfaces is modulated by biomaterial type and surface treatment

An In Vitro Study regarding the Wear of Composite Materials Following the Use of Dental Bleaching Protocols

Influence of dual-cure and self-cure abutment cements for crown implants on human gingival fibroblasts biological properties

The effect of toothbrushing on surface gloss of resin composites

Effect of Reduced-Step Polishing Systems on Color Stability of Nanocomposites Submitted to Thermocycling Staining with Common Beverages - An In Vitro Study