Abstract:Abstract Laser-induced breakdown spectroscopy (LIBS) is one of the most promising methods for quantitative in-situ determination of fuel retention in plasma-facing components (PFCs) of magnetically confined fusion devices like ITER and JET. In this article, the current state of understanding in LIBS development for fusion applications will be presented, based on a complete review of existing results and complemented with newly obtained data. The work has been performed as part of a research programme, set up in the EUROfusion Consortium, to address the main requirements for ITER: (a) quantification of fuel from relevant surfaces with high sensitivity, (b) the technical demonstration to perform LIBS with a remote handling system and (c) accurate detection of fuel at ambient pressures relevant for ITER. For the first goal, the elemental composition of ITER-like deposits and proxies to them, including deuterium (D) or helium (He) containing W–Be, W, W–Al and Be–O–C coatings, was successfully determined with a typical depth resolution ranging from 50 up to 250 nm per laser pulse. Deuterium was used as a substitute for tritium (T) and in the LIBS experiments deuterium surface densities below 10 16 D/cm 2 could be measured with an accuracy of ∼30%, confirming the required high sensitivity for fuel-retention investigations. The performance of different LIBS configurations was explored, comprising LIBS systems based on single pulse (pulse durations: ps–ns) and double pulse lasers with different pulse durations. For the second goal, a remote handling application was demonstrated inside the Frascati-Tokamak-Upgrade (FTU), where a compact, remotely controlled LIBS system was mounted on a multipurpose deployer providing an in-vessel retention monitor system. During a shutdown phase, LIBS was performed at atmospheric pressure, for measuring the composition and fuel content of different area of the stainless-steel FTU first wall, and the titanium zirconium molybdenum alloy tiles of the toroidal limiter. These achievements underline the capability of a LIBS-based retention monitor, which complies with the requirements for JET and ITER operating in DT with a beryllium wall and a tungsten divertor. Concerning the capabilities of LIBS at pressure conditions relevant for ITER, quantitative determination of the composition of PFC materials at ambient pressures up to 100 mbar of N 2 , the D content could be determined with an accuracy of 25%, while for atmospheric pressure conditions, an accuracy of about 50% was found when using single-pulse lasers. To improve the LIBS performance in atmospheric pressure conditions, a novel approach is proposed for quantitative determination of the retained T and the D/T ratio. This scenario is based on measuring the LIBS plume emission at two different time delays after each laser pulse. On virtue of application of a double pulse LIBS system, for LIBS application at N 2 atmospheric pressure the distinguishability of the spectra from H isotopes could be significantly improved, but further systematic research is required.

Measuring Impurity Concentration in Near Wall Plasma During Tests of Prototypes of the First Wall of Fusion Reactor in PLM Facility

Impact of Impurity Mixture Gas Seeded by Supersonic Molecular Beam Injection on Edge-Localized Modes in the HL-2A Tokamak

Plasma performance enhancement and impurity control by novel technique of argon-hydrogen mixture fueled glow discharge wall conditioning in ADITYA-U tokamak

Monitoring of tritium and impurities in the first wall of fusion devices using a LIBS based diagnostic

Impurity behaviour in JET high-current baseline scenario for Deuterium, Tritium and Deuterium-Tritium plasmas

Challenges for plasma-facing components in nuclear fusion

Experimental estimation of tungsten impurity sputtering due to Type I ELMs in JET-ITER-like wall using pedestal electron cyclotron emission and target Langmuir probe measurements

Technique of Reactor Experiments of Tin-Lithium Alloy Interaction with Hydrogen Isotopes Under Neutron Irradiation Conditions

Critical Exploration of Liquid Metal Plasma-Facing Components in a Fusion Nuclear Science Facility

Moderation of neoclassical impurity accumulation in high temperature plasmas of helical devices

Dynamic outgassing of deuterium, helium and nitrogen from plasma-facing materials under DEMO relevant conditions

Metallography and mechanical parameters of plasma-exposed plasma-facing materials and components

Possible Studies of Explosively Driven Non-Ideal Plasma Using a Proton Microscope at the Facility for Antiprotons and Ion Research

Development of a Complex for Materials Science Studies on the T-15MD Tokamak

Investigation of Impurity Confinement in Lower Hybrid Wave Heated Plasma on EAST Tokamak

A Metal-Wall Compatible High-Confinement Tokamak Plasma Regime for Fusion Energy

Neutron Emission Spectrometer To Measure Ion Temperature On The Fusion Demonstration Plant

The Plasma-Facing Materials of Tokamak Thermonuclear Reactors: Requirements, Thermal Stabilization, and Tests (a Review)

ICRH-related impurity source and control across experiments in H, D, T plasmas at JET-ILW

Confinement and Heating of a Deuterium-Tritium Plasma

Experience in the Development of Liquid Metal Plasma Facing Elements Based on Capillary-Porous Structures for a Steady-State Tokamak (Survey)