Abstract:Highly-conductive nanostructures may be dispersed into phase change materials (PCM) to improve their effective thermal conductivity, thus leading to colloidal systems that are referred to as nanostructure-enhanced PCM (NePCM). Results of a theoretical and experimental investigation on freezing of NePCM in comparison to the base PCM are presented. A one-dimensional Stefan model was developed to study the unidirectional freezing of NePCM in a finite slab. Only the thermal energy equation was considered and the presence of static dispersed nanoparticles was modeled using effective media relations. A combination of analytical and integral methods was used to solve this moving boundary problem. The elapsed time to form a given thickness of frozen layer was therefore predicted numerically. A cooled-from-bottom unidirectional freezing experimental setup was designed, constructed, and tested. Thermocouple readings were recorded at several equally spaced locations along the freezing direction in order to monitor the progress of the freezing front. As an example, cyclohexane (C6H12) and copper oxide (CuO) nanoparticles were chosen to prepare the NePCM samples. The effective thermophysical and transport properties of these samples for various particle loadings (0.5/3.8, 1/7.5, and 2/14.7 vol. %/wt. %) were determined using the mixture and Maxwell models. Due to utilization of the Maxwell model for thermal conductivity of both phases, the numerical predictions showed that the freezing time is shortened linearly with increasing particle loading, whereas nonmonotonic expediting was observed experimentally. The maximum expediting was found to be nearly 8.23% for the 0.5 vol. % sample. In the absence of a nanoparticle transport model, the mismatch of the cold plate boundary conditions, lack of accurate thermophysical properties, especially in the solid phase of NePCM samples and precipitation issues with 2 vol. % samples were addressed by improving the experimental setup. Through adopting a copper cold plate, utilizing measured thermal conductivity data for both phases and using 1, 2, and 4 wt. % samples, good agreement between the experimental and numerical results were realized. Specifically, adoption of measured thermal conductivity values for the solid phase in the Stefan model that were originally underestimated proved to be a major cause of harmony between the experiments and predictions. [DOI: 10.1115/1.4006305]

Numerical simulation of solidification through wavy storage container in existence of nanoparticles

Development of numerical code for mathematical simulating of unsteady solidification phenomena in existence of nanomaterial

Expedited Freezing of Nanoparticle-Enhanced Phase Change Materials (nepcm) Exhibited Through A Simple 1-D Stefan Problem Formulation

Thermal assessment of storage unit during solidification in existence of different configuration of nano-powders

Simulations of transient heat transfer within cold-storage unit during solidification incorporating nanomaterial

The increment of performance of cold storage via simulating unsteady solidification utilizing nanomaterial

A Similarity Solution to Unidirectional Solidification of Nano-Enhanced Phase Change Materials (nepcm) Considering the Mushy Region Effect

Incorporating numerical method for analyzing the conduction heat transfer during solidification loading nanoparticles

A Theoretical and Experimental Investigation of Unidirectional Freezing of Nanoparticle-Enhanced Phase Change Materials

Analyzing cold storage unit during discharging process involving pure conduction utilizing nanomaterial

An Experimental Study of Inward Solidification of Nano-Enhanced Phase Change Materials (nepcm) Inside A Spherical Capsule

Efficacy of dispersing nano-powders on rate of cold storage during solidification considering transient conduction

Effects of Nanoparticles and Sample Containers on Crystallization Supercooling Degree of Nanofluids

A volume-shrinkage-based method for quantifying the inward solidification heat transfer of a phase change material filled in spherical capsules

Improvement of water solidification via nanotechnology considering transient conduction within finned tank

A comparative study between two-dimensional and three-dimensional simulation results of melting inside a container

Evaluation of thermal storage system during freezing and loading nano-powders

Assessment of cold storage system in existence of nanomaterial using Galerkin technique

Numerical Simulation of the Melting of Solid Particles in Thermal Convection with a Modified Immersed Boundary Method

Heat transfer during discharging of NEPCM through the finned container

Modeling the freezing of nanomaterial through the cold storage unit implementing numerical approach