Abstract:In friction stir welding (FSW), the inhomogeneous microstructure significantly affects the mechanical performance of the joints. The present study investigates the influence of microstructural asymmetry along the thickness on strain localization during tensile test using the digital image correlation technique and fracture morphology for double‐sided FSW (DS‐FSW) AA6061‐AA7075 joints. In top and bottom slices of the transverse tensile sample, nonhomogenous strain localization is noted in heat affected zone (HAZ) of the advancing side (AS), that is, AA6061‐T6, and also presents higher tensile strength. However, in the middle slice of the transverse sample, larger region including thermo‐mechanically affected zone and HAZ undergoes strain localization and exhibits higher elongation at failure. In longitudinal specimens, the strain distribution is homogeneous up to uniform elongation followed by strain concentration at a localised region and fracture. Electron backscatter diffraction revealed that the extent of dynamic recrystallization on the retreating side (AA7075‐T61) is higher than that observed on the AS of the weld. The grain orientation spread map showed a high fraction of recrystallized grains at the weld centre. Presence of major shear textures components B/B¯ and C both below the tool shoulder and weld centre regions are observed from pole figures. The recrystallized texture components P ({011}<112>), Goss ({110}<001>), Rotated Goss ({110}<110>), Cube ({001}<100>) and shear texture ({001}<110>) components is also noted at the weld centre. Middle slice both for longitudinal and transverse sample showed the finest dimple size on the fracture surfaces. The strain localization behaviour and tensile performance assessed for transverse and longitudinal samples can be helpful to find the load orientation dependency and safe design of DS‐FSW joints.

Investigation on Microstructure and Residual Stress Distribution in Dissimilar AA3105/AA2024 Friction Stir Joints

Investigations on surface properties of friction stir welded dissimilar AA2024-T3 and 304 stainless steel joints

Investigation on the mechanical properties and microstructural analysis of dissimilar friction stir welding of AA5154/AA7150

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Residual Stresses of Friction Stir Welded 2024-T4 Joints

Microstructural Characterisation and Mechanical Properties of Dissimilar AA5083-copper Joints Produced by Friction Stir Welding

Residual Stresses for Friction Stir Welded Al Sheets

Investigation of the microstructure, mechanical properties and fracture mechanisms of dissimilar friction stir welded aluminium/titanium joints

Microstructure evolution and mechanical properties of friction stir welded joint of ultrafine-grained dissimilar AA2024/AA5083 composite fabricated by accumulative roll bonding

Residual stress measurement of Al/steel dissimilar friction stir weld

Influence of Material Properties on Microstructure and Mechanical Properties of Aluminum Alloy FSW Joints

Grain Structure and Texture Evolution in the Bottom Zone of Dissimilar Friction-Stir-Welded AA2024-T351 and AA7075-T651 Joints

Investigation of mechanical, metallurgical and corrosion characteristics of friction stir welded dissimilar AA 5052-H32 and AA 6061-T6 joints

Study on the effect of the welding environment on the dynamic recrystallization phenomenon and residual stresses during the friction stir welding process of aluminum alloy

Microstructure and fatigue performance of friction stir welded joints of 2A12‐T4 and 7075‐T6 dissimilar aluminum alloy

Friction stir welding of AA2024-T3 and SS304 alloys: Microstructural analysis, microhardness evaluation, and tensile performance

Effect of microstructural variation on strain localization in double‐sided friction stir welded AA6061‐AA7075 joints

Evaluation of dissimilar 7075 aluminum/AISI 304 stainless steel joints using friction stir welding

Microstructure evolution of thermo-mechanically affected zone in dissimilar AA2024/7075 joint produced by friction stir welding

Residual Stress, Microstructure and Mechanical Properties in Thick 6005A-T6 Aluminium Alloy Friction Stir Welds

Electrochemical and mechanical behaviors of dissimilar friction stir welding between 5086 and 6061 aluminum alloy