Abstract:The development of next-generation secondary batteries hinges on the design of energy storage materials with high-rate properties capable of high-speed charge/discharge. For example, in order to eliminate 'range anxiety,' which is one of the key problems that makes people hesitate to acquire electric vehicles, it is necessary to build a rechargeable battery that can be recharged in minutes. The high current density applied to the electrode during high-speed charging/discharging, however, generates a lithium ion concentration gradient inside the electrode, which causes a variety of issues. Furthermore, one of the key reasons for the difficulties in creating energy storage materials with high high-rate qualities is the material's inherent properties, such as ion transport restriction. We used laser processing and a dry transfer procedure to create a negative electrode plate for a lithium ion secondary battery with a surface aligned in a certain orientation. When compared to the existing electrode plate, laser-induced graphene (LIG), a porous three-dimensional nanomaterial generated by laser processing, had a higher specific surface area and a three-dimensional network structure. The fracture surface of the LIG, whose plane orientation was configured in this easy-to-transfer direction, was discovered to have a significant impact on rate capabilities. A commercially available polyimide (PI) film (thickness: 125 μm, Kapton) was used to make the LIG-based negative plate used in this investigation, which was treated with a CO 2 laser with a wavelength of 10.6 μm. The irradiated laser had a power output of 5.4 W, and the scan speed and pitch were kept at 200 mm/s and 125 μm, respectively. Press-type roll forming was used to transfer the so produced LIG to a copper substrate with a thickness of around 20 μm, with the distance between the rolls controlled between 70 and 200 μm and the specimen feed rate controlled between 10-100 mm/s. For electrochemical evaluation, the negative plate was made up of 2032 typed coin cells, and for material evaluation, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy were used. Despite applying a high current density of 20 A/g at a loading level of around 3 mg/cm 2 , this electrode obtained a discharge capacity of 114 mAh/g within 3 minutes, corresponding to 95 percent of the material. The great specific surface area of nanomaterials like graphene, as well as the three-dimensional structure in which the surface is oriented in a precise direction due to dry transfer, account for the unusually high rate. In other words, the lowered internal charge transfer resistance helps to realize high rate characteristics because the holey-structured graphene with high porosity due to laser processing is well stacked in a three-dimensional structure. Furthermore, because the electrode surface is structured in a structure with multiple edge plane exposures, it was feasible to create an anode material with high rate characteristics by shortening the lithium ion transport and diffusion distance. This method can be easily applied to the current negative electrode material and electrode manufacturing process for lithium ion secondary batteries, and it has the potential to be extended and applied to material manufacturing methods for a variety of applications that improve charge and ion transport.

Enhanced immersion cooling using laser-induced graphene for Li-ion battery thermal management

Electrochemical–Thermal Evaluation of an Integrated Thermal Management System for Lithium‐Ion Battery Modules

Thermal Management for the Prismatic Lithium-Ion Battery Pack by Immersion Cooling with Fluorinated Liquid

Numerical Study on Heat Dissipation and Structure Optimization of Immersed Liquid Cooling Mode Used in 280ah LiFePO4 Batteries

Thermal management for the 18650 lithium-ion battery pack by immersion cooling with fluorinated liquid

Immersion cooling for lithium-ion batteries – A review

Numerical Study on Heat Dissipation and Structure Optimization of Immersed Liquid Cooling Mode Used in 280ah LiFePO4 4 Batteries

Graphene Based Thermal Management System for Battery Cooling in Electric Vehicles

Carbon and Graphene Coatings for the Thermal Management of Sustainable LMP Batteries for Automotive Applications

Numerical and experimental investigations on heat transfer characteristics and influencing factors of immersion cooling system for high-capacity prismatic lithium-ion battery

Experimental Study on Dielectric Fluid Immersion Cooling for Thermal Management of Lithium-Ion Battery

Thermal characterization of pouch cell using infrared thermography and electrochemical modelling for the Design of Effective Battery Thermal Management System

Graphene-enhanced hybrid phase change materials for thermal management of Li-ion batteries

An experimental investigation of liquid immersion cooling of a four cell lithium-ion battery module

Laser-Induced Graphene(LIG)-Based Anode Electrode for High-Rate Lithium-Ion Batteries

CFD and Experimental Investigation of Graphite Heat Spreader Based Cooling for Li-Ion Batteries for Electric Vehicles and EVTOL (Electric Vertical Take-Off and Landing) Aircraft Applications

Numerical investigation of the effect of prepared phase change material-expanded graphite composite and vertical air ducts on the thermal performance of a Li-ion battery

A Graphene‐Coated Thermal Conductive Separator to Eliminate the Dendrite‐Induced Local Hotspots for Stable Lithium Cycling

Numerical investigation on integrated thermal management for a lithium-ion battery module with a composite phase change material and liquid cooling

Experimental investigation on a novel phase change material composites coupled with graphite film used for thermal management of lithium-ion batteries

Engineered heat dissipation and current distribution boron nitride-graphene layer coated on polypropylene separator for high performance lithium metal battery