Abstract:A two‐step pyrolysis strategy is developed to construct 2D porous Cu3N catalysts for efficient CO electroreduction to multicarbon products. The high‐purity Cu3N with abundant hierarchical pores demonstrated a C2+ faradaic efficiency exceeding 90% at 0.6 A cm−2 and 87% selectivity at 1 A cm−2, attributed to high coverage and adsorption of CO intermediates, which facilitate C‐C coupling and the formation of C2+ products. The maturation of CO2 electrolysis to CO technology has rendered a cascade catalysis scheme, utilizing CO reduction as a media step, a promising strategy to produce high‐value C2+ fuel. However, the current catalysts employed in CO electroreduction (ECORR) face severe hydrogen evolution reactions at high current densities. Herein, a 2D porous Cu3N (2D‐P‐Cu3N) catalyst is reported with outstanding ECORR performance prepared by a two‐step pyrolysis strategy. This strategy mainly relies on the sequential annealing of the Cu2(OH)2CO3 precursors in an oxidation and reduction atmosphere, which can not only convert it into high‐purity Cu3N, but also endow it with an abundant hierarchical pores structure. The pores can significantly improve the in‐plane conductivity and mass transfer capacity of Cu3N, enabling a C2+ faradaic efficiency exceeding 90% at a current density of 0.6 A cm−2. Even at an ampere grade current density of 1 A cm−2, it maintains an impressive 87% selectivity, surpassing most of the reported Cu‐based catalysts. In‐situ Raman spectroscopy confirms that 2D‐P‐Cu3N exhibits high coverage and adsorption of CO intermediates, thus enhancing C‐C coupling and promoting the generation of C2+ products. This discovery opens further exploration of catalysts for selective CORR to C2+ products.

The enhanced local CO concentration for efficient CO 2 electrolysis towards C2 products on tandem active sites

Confined Cu I sites in partially electro-reduced 2D conductive Cu-MOF film for boosting CO 2 electrocatalysis to C2 products

Constructing Cu0/Cu+ interfaces on Cu-based MOFs derivatives to promote the adsorption stability of intermediates in the process of CO2 electroreduction to C2 products

Enriching the Local Concentration of CO Intermediates on Cu Cavities for the Electrocatalytic Reduction of CO2 to C2+ Products.

Enhanced CO Affinity on Cu Facilitates CO<sub>2</sub> Electroreduction toward Multi-Carbon Products

Single‐Site Metal–Organic Framework and Copper Foil Tandem Catalyst for Highly Selective CO2 Electroreduction to C2H4

Interstitial carbon induces enriched Cuδ+ sites in Cu2O nanoparticles to facilitate CO2 electroreduction to C2+ products

Hetero-Interfaces on Cu Electrode for Enhanced Electrochemical Conversion of CO 2 to Multi-Carbon Products.

Local CO Generator Enabled by a CO-Producing Core for Kinetically Enhancing Electrochemical CO2 Reduction to Multicarbon Products

Enhanced electroreduction of CO<sub>2</sub> to C<sub>2+</sub> products on heterostructured Cu/oxide electrodes

A 2D Porous Cu3N Catalyst for Efficient CO Electroreduction to Multicarbon Products at an Ampere Level Current Density

Lowering *CO Affinity over Cu Nanoparticles for Enhanced Electrochemical CO 2 Conversion to Multi-Carbon Products at High Current Density

Performance Enhancement and Active Sites Identification of Cu-Cd Bimetallic Oxide Derived Catalysts for Electrochemical CO 2 Reduction

Enhanced electroreduction of CO2 to C2+ products on heterostructured Cu/oxide electrodes

Development of Mn/Cu Bi-metallic MOF for electrochemical CO2 reduction into valuable products

Cu2O-Ag Tandem Catalysts for Selective Electrochemical Reduction of CO2 to C2 Products

Direct Low Concentration CO2 Electroreduction to Multicarbon Products Via Rate-Determining Step Tuning

Stabilizing Cu+ Species in Cu2O/CuO Catalyst via Carbon Intermediate Confinement for Selective CO2RR

Identification of Cu0/Cu+/Cu0 interface as superior active sites for CO2 electroreduction to C2+ in neutral condition

Selective CO2 Electroreduction to Multi-Carbon Products on Organic-Functionalized CuO Nanoparticles by Local Micro-Environment Modulation

Joint tuning the morphology and oxygen vacancy of Cu2O by ionic liquid enables high-efficient CO2 reduction to C2 products