Abstract:Background: In the regenerative treatment of intrabony periodontal defects, surgical strategies are primarily determined by defect morphologies. In certain cases, however, direct clinical measurements and intraoral radiographs do not provide sufficient information on defect morphologies. Therefore, the application of cone-beam computed tomography (CBCT) has been proposed in specific cases. 3D virtual models reconstructed with automatic thresholding algorithms have already been used for diagnostic purposes. The aim of this study was to utilize 3D virtual models, generated with a semi-automatic segmentation method, for the treatment planning of minimally invasive periodontal surgeries and to evaluate the accuracy of the virtual models, by comparing digital measurements to direct intrasurgical measurements. Methods: Four patients with a total of six intrabony periodontal defects were enrolled in the present study. Two months following initial periodontal treatment, a CBCT scan was taken. The novel semi-automatic segmentation method was performed in an open-source medical image processing software (3D Slicer) to acquire virtual 3D models of alveolar and dental structures. Intrasurgical and digital measurements were taken, and results were compared to validate the accuracy of the digital models. Defect characteristics were determined prior to surgery with conventional diagnostic methods and 3D virtual models. Diagnostic assessments were compared to the actual defect morphology during surgery. Results: Differences between intrasurgical and digital measurements in depth and width of intrabony components of periodontal defects averaged 0.31 ± 0.21 mm and 0.41 ± 0.44 mm, respectively. In five out of six cases, defect characteristics could not be assessed precisely with direct clinical measurements and intraoral radiographs. 3D models generated with the presented semi-automatic segmentation method depicted the defect characteristics correctly in all six cases. Conclusion: It can be concluded that 3D virtual models acquired with the described semi-automatic segmentation method provide accurate information on intrabony periodontal defect morphologies, thus influencing the treatment strategy. Within the limitations of this study, models were found to be accurate; however, further investigation with a standardized validation process on a large number of participants has to be conducted.

A Life-Size Three-Dimensional Phantom for Periodontal Imaging Development and Treatment-Planning

3D-printed neck phantoms with detailed anatomy for ultrasound-guided procedure and device testing

High-fidelity anatomical phantoms for MRI practical training

A Multimodal Phantom for Visualization and Assessment of Histotripsy Treatments on Ultrasound and X-Ray Imaging

Promoting simulation-based training in radiology: A homemade phantom for the practice of ultrasound-guided procedures

An anthropomorphic maxillofacial phantom using 3-dimensional printing, polyurethane rubber and epoxy resin for dental imaging and dosimetry

3-D Stochastic Numerical Breast Phantoms for Enabling Virtual Imaging Trials of Ultrasound Computed Tomography

Development of a Digital Breast Phantom for Photoacoustic Computed Tomography

High-Resolution Ultrasonic Imaging of Dento-Periodontal Tissues Using a Multi-Element Phased Array System

Development of a CT-Compatible, Anthropomorphic Skull and Brain Phantom for Neurosurgical Planning, Training, and Simulation

A multi-modality medical imaging head and neck phantom: Part 2. Medical imaging

Digital three-dimensional visualization of intrabony periodontal defects for regenerative surgical treatment planning

A patient-specific multi-modality abdominal aortic aneurysm imaging phantom

Development of binder-jetting based skull phantoms for transcranial ultrasound research

Intraoral Ultrasound Imaging Using a Rotational Transducer with Periodontal Feature Identification by Machine Learning

Fine structural human phantom in dentistry and instance tooth segmentation

Patient-Specific Vascular Flow Phantom for MRI- and Doppler Ultrasound Imaging

Photoacoustic digital tooth and image reconstruction of tooth root

Development of an anatomical breast phantom from polyvinyl chloride plastisol with lesions of various shape, elasticity and echogenicity for teaching ultrasound examination

Ultrasonography‐Guided Dental Implant Surgery: A Feasibility Study

Simulating submandibular area with everyday-use materials in dental education: A didactic US study