Abstract:Gibbs adsorption and Zener pinning induced by MgB2 decomposition are proven to inhibit grain growth for enhancing mechanical properties and cutting processibility of Bi2Te3‐based alloys with improved thermoelectric performance. An average figure of merit of 1.1 within 300–473 K can be obtained in (Bi0.4Sb1.6Te3)0.97(MgB2)0.03, and an energy conversion efficiency of 4.2% at a temperature difference of 215 K can be achieved in an eight‐pair device. Bi2Te3‐based alloys have great market demand in miniaturized thermoelectric (TE) devices for solid‐state refrigeration and power generation. However, their poor mechanical properties increase the fabrication cost and decrease the service durability. Here, this work reports on strengthened mechanical robustness in Bi2Te3‐based alloys due to thermodynamic Gibbs adsorption and kinetic Zener pinning at grain boundaries enabled by MgB2 decomposition. These effects result in much‐refined grain size and twofold enhancement of the compressive strength and Vickers hardness in (Bi0.5Sb1.5Te3)0.97(MgB2)0.03 compared with that of traditional powder‐metallurgy‐derived Bi0.5Sb1.5Te3. High mechanical properties enable excellent cutting machinability in the MgB2‐added samples, showing no missing corners or cracks. Moreover, adding MgB2 facilitates the simultaneous optimization of electron and phonon transport for enhancing the TE figure of merit (ZT). By further optimizing the Bi/Sb ratio, the sample (Bi0.4Sb1.6Te3)0.97(MgB2)0.03 shows a maximum ZT of ≈1.3 at 350 K and an average ZT of 1.1 within 300–473 K. As a consequence, robust TE devices with an energy conversion efficiency of 4.2% at a temperature difference of 215 K are fabricated. This work paves a new way for enhancing the machinability and durability of TE materials, which is especially promising for miniature devices.

Strong and efficient bismuth telluride-based thermoelectrics for Peltier microcoolers

High Performance BiSbTe Alloy for Superior Thermoelectric Cooling

Synergistically enhanced thermoelectric and mechanical performance of Bi 2 Te 3 via industrial scalable hot extrusion method for cooling and power generation applications

Gibbs Adsorption and Zener Pinning Enable Mechanically Robust High‐Performance Bi2Te3‐Based Thermoelectric Devices

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

High-Performance p-Type Bi 2 Te 3 -Based Thermoelectric Materials Enabled via Regulating Bi-Te Ratio

Thermoelectric Cooling‐Oriented Large Power Factor Realized in N‐Type Bi2Te3 Via Deformation Potential Modulation and Giant Deformation

Hierarchical Low-Temperature n-Type Bi2Te3 with High Thermoelectric Performances

Designing Cost-Performance Porous Thermoelectric Materials by Interface Engineering Through Atomic Layer Deposition

Thermoelectric cooling materials

Synergistically Optimized Thermoelectric and Mechanical Properties in p ‐Type BiSbTe by a Microdroplet Deposition Technique

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

The Thermoelectric Properties of Bismuth Telluride

Attaining high mid-temperature performance in (Bi,Sb) 2 Te 3 thermoelectric materials via synergistic optimization

General strategy for developing thick-film micro-thermoelectric coolers from material fabrication to device integration

Significant Enhancement of Thermoelectric Figure of Merit in BiSbTe‐Based Composites by Incorporating Carbon Microfiber

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

Design of N‐Type Textured Bi2Te3 with Robust Mechanical Properties for Thermoelectric Micro‐Refrigeration Application

Next-generation thermoelectric cooling modules based on high-performance Mg3(Bi,Sb)2 material

Thin-film thermoelectric devices with high room-temperature figures of merit

High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys