Abstract:Photoelectrochemical water splitting (PEC) is a viable solution for addressing future environmental and energy concerns. However, due to the high cost of photoelectrodes and the limitations of sluggish kinetics, practical applications are limited. To achieve that goal, effective solutions are still needed to create low-cost photoelectrodes suited for PEC. Transistion metal sulfides (TMS) materials have a high potential for use as photoelectrodes due to their favorable and impressive properties 1 . The photoactivity of TMS is typically unlimited due to low reflection at the grain boundary. The individual atomic thin sheets with higher surface area compared to bulk materials allow for faster diffusion of photoinduced charge carriers primarily due to the less interface between their grains. Their lower interfacial contact resistance enables enhanced charge dynamics and, as a result, improved electrochemical reaction kinetics. When compared to other TMS, CdS has a direct bandgap and excellent photoactivity. However, its toxicity and photocorrosion make it unsuitable for long-term practical use. WS 2 is well-known layered transition metal sulfide that has a 2D molybdenite structure. It is non-toxic in acidic/neutral solutions that are chemically stable. It has been demonstrated to be more stable against oxidation and photo corrosion than CdS, which is extensively employed in photocatalysis 2 . However, because of the recombination of photoinduced charge carriers, pure WS 2 exhibits relatively poor photocatalytic efficiency and stability. As a result, combining WS 2 based photoactive nanomaterials with other suitable materials has helped overcome this challenge. Transistion metal sulfides with acceptable band structures for heterostructure construction with WS 2 may enable breakthroughs in photocatalytic and photo-electrochemical processes. The primary focus of this work is to construct heterostructures by combining CdS and WS 2 and to investigate their role as photoanodes of semiconductor materials in PEC water splitting. In this work, we have synthesised heterostructures using a facile solution-reaction method and Successive Ionic Layer Adsorption Reaction deposition (SILAR) technique which is intrinsically cost effective and scalable 3 . The heterostructure is characterised by XRD, SEM and TEM. We also studied the performance enhancement of this heterostructure using Linear sweep voltammetry and Electrochemical impedance spectroscopy. Pristine WS 2 and CdS showed photocurrent densities of 3 μA cm -2 and 20 μA cm -2 . However, heterostructures formation led to much improved photocurrents. Photocurrent densities of 151 μA cm -2 were observed for WS 2 /CdS heterostructures respectively at 1.23 V vs RHE. The enhanced improvement in photoelectrochemical performance in the case of the heterostructures could be due to the following factors: (a) the intimate interaction of this unique heterostructure improves adhesion and lowers the photoinduced charge transfer barrier; (b) increased light harvesting capability; and (c) improved charge dynamics of photoinduced charge carriers due to proper band alignment. The current study paves the way for further research into the creation of metal sulfide heterostructures that generate analogous photoelectrode materials. Keywords: Photoelectrochemical water splitting, metal sulfides, photoelectrodes. Figure 1

Surface Epitaxial Growth of 2D/2D Bi2O2S/CdS Heterojunction Photoanodes and Their Photoelectrochemical Properties

Highly Efficient 2D/3D Structured CuCo2S4/CdIn2S4 Composites with a P–n Heterojunction for Boosting Photocatalytic Hydrogen Evolution

Highly efficient 3D/0D CdIn2S4/Cu2O photoanode with p-n type heterojunction for boosted photoelectrochemical water splitting under visible light irradiation

Epitaxial grown [hk1] oriented 2D/1D Bi2O2S/Sb2S3 heterostructure with significantly enhanced photoelectrochemical performance

Facile Construction TiO2/ZnIn2S4/Zn0.4Ca0.6In2S4 Ternary Hetero-Structure Photo-Anode with Enhanced Photo-Electrochemical Water-Splitting Performance

Synthesis of a Cu 2 O/Carbon Film/NiCoB‐Grpahene Oxide Heterostructure As Photocathode for Photoelectrochemical Water Splitting

General In Situ Photoactivation Route with IPCE over 80% toward CdS Photoanodes for Photoelectrochemical Applications

Combined CdS/In2S3 heterostructures with cocatalyst for boosting carriers separation and photoelectrochemical water splitting

Piezoelectric‐Effect‐Enhanced Full‐Spectrum Photoelectrocatalysis in P–n Heterojunction

Synthesis and improved photoelectrochemical performances of Bi9O7.5S6/CdS heterojunction

Realizing Efficient Photoelectrochemical Performance for Well-Designed CdS@ZnIn2S4 Heterostructure Photoanode with Directional Interfacial Charge Transfer Dynamics

Enhanced Photoelectrochemical Performance in Engineered Interface 2D Metal Sulfide Heterostructures for Water Splitting

Ferroelectric polarization promotes a CdS/In2Se3 heterostructure for photocatalytic water splitting

Enhanced photoelectrochemical water splitting efficiency of CdS through Fe-S-Cd carrier channel facilitated interfacial charge transfer

Enhanced PEC Water Splitting Efficiency by Type II Heterojunction CdIn2S4/g-C3N4 Photoanode Construction

Combined heterostructures between Bi2S3 nanosheets and H2-treated TiO2 nanorods for enhanced photoelectrochemical water splitting

Construction of CuBi2O4/CdO p-n buried junction for boosted photoelectrochemical water splitting

Multidimensional CdS nanowire/CdIn2S4 nanosheet heterostructure for photocatalytic and photoelectrochemical applications

Bi2S3 Nanoparticles on Bi2MoO6 Nanorods for Applications As Fast-Response Self-Powered Photoelectrochemical Photodetector and Water Splitting

Diethylenetriamine Synergistic Boosting Photocatalytic Performance with Porous G-C3n4/cds-diethylenetriamine 2D/2D S-scheme Heterojunction

Type-II Heterojunction CdIn2S4/BiVO4 Coupling with CQDs to Improve PEC Water Splitting Performance Synergistically