Abstract:Aim. To compare and contrast by three-dimensional finite element analysis the biomechanical performance of deep mesio-occlusal-distal cavities of mandibular molars reinforced by different sizes of horizontal fiber posts. Materials and Methods. The finite element (FE) stress analysis was performed with the ANSYS, a commercial finite element method package. Based on the evidence-based scientific data and on the mechanical properties of materials, i.e., Young's modulus and Poisson ratio, the model of a mandible and mandibular first molar was replicated. The mandibular molar models replicating the clinical scenarios were simulated, designed, and built, assuming all materials to be homogenous, isotropic, and linearly elastic as follows: Model 1 control: the model of an intact first mandibular molar. Model 2: the prepared cavity mesio-occlusal-distal is replicated by the subtraction Boolean method. The remaining thickness of dentin is 1 mm. Model 3: these were rehabilitated by three different diameters of two horizontal fiber posts. Model 3A: fiber post diameter 1 mm, Model 3B: 1.5 mm and Model 3C: 2 mm. The dimensions of the cavity, the intercuspal distance between buccal walls and lingual walls, and the distance of placement of the post from occlusal reference points were all kept constant for all three subgroups of Model 3. The cavities of Model 3 were restored with Filtek bulk-fill posterior composite. After meshing the models, loads were defined on the buccal and lingual distal cusps with a constant value of 600 N and at an angle of 45°. Results. The results of finite element analysis are expressed as stresses, i.e., tensile compressive, shear, or a combination known as von Mises stresses. The overall von Mises stresses were as follows: Model 1:154.83 Mpa; Model 2: 376.877 Mpa; Model 3A: 160.221 Mpa; Model 3B: 159.488 Mpa; Model 3C: 147.231 Mpa. Statistical analysis of the compiled data was carried out. It was seen that there was a significant difference in stress values from the intact tooth Model 1 and cavity Model 2 ( p < 0.05 ) with means values of 53.1 and 139.22, respectively. The means of all subgroups were comparable but there was a statistically significant difference between Model 3, i.e., 3A (67.74), Model 3B (60.47), Model 3C (53.70), and Model 2. Model 1 and Model 3C had comparable mean values. Conclusion. Rehabilitation of deep mesio-occlusal-distal cavities of molars with intact buccal and lingual walls with the aid of a horizontal post of any diameter has a similar stress distribution to an intact tooth. However, the biomechanical performance of a 2 mm horizontal post was exacting of the natural tooth. Horizontal posts can be included in expanding our restorative option for rehabilitating grossly mutilated teeth.

Comparative Evaluation of Stress Distribution and Deformation in Class II Cavities Restored With Two Different Biomimetic Restorative Materials: A Three-Dimensional Finite Element Analysis

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

Numeric simulation of occlusal interferences in molars restored with ultrathin occlusal veneers

Stress distribution in endodontically treated external cervical resorption lesions restored with MTA and biodentine - A finite element analysis

Comparison of the biomechanical effects of the post-core crown, endocrown and inlay crown after deep margin elevation and its clinical significance

Effect of Biomimetic Material on Stress Distribution in Mandibular Molars Restored with Inlays: a Three-Dimensional Finite Element Analysis

[The Finite Element Analysis of Stress Distribution in Different Size of MO Cavities Restored with Composite Resin Inlays].

Computer Aided Design Modelling and Finite Element Analysis of Premolar Proximal Cavities Restored with Resin Composites

[Finite Element Analysis of First Maxillary Molars Restored with Different Post and Core Materials].

The use of different adhesive filling material and mass combinations to restore class II cavities under loading and shrinkage effects: a 3D-FEA

Three-dimensional Finite Element Stress of the Medial-Occlusal (class Ⅱ)cavity Restored with Different Inlay

Finite Element Analysis and Clinical Applications of Transverse Post for the Rehabilitation of Endodontically Treated Teeth

Comparison of Bulk Polymeric Resin Composite and Hybrid Glass Ionomer Cement in Adhesive Class I Dental Restorations: A 3D Finite Element Analysis

Comparative Evaluation of Different Post Materials on Stress Distribution in Endodontically Treated Teeth Using the Finite Element Analysis Method: A Systematic Review

Biomechanical performance of resin composite on dental tissue restoration: A finite element analysis

Biomechanical Performance of Mandibular Molars with Deep Mesio-Occlusal-Distal Cavities Rehabilitated with Horizontal Posts: A 3D Finite Element Analysis

Evaluation of two CAD/CAM materials for Nayyar core and post-retained restorations: Three dimensional stress analysis

Mechanical Behavior of Different Restorative Materials and Onlay Preparation Designs in Endodontically Treated Molars

Finite element and in vitro study on biomechanical behavior of endodontically treated premolars restored with direct or indirect composite restorations

A Finite Element Method Study of Stress Distribution in Dental Hard Tissues: Impact of Access Cavity Design and Restoration Material

Influence of restorative material and cement on the stress distribution of endocrowns: 3D finite element analysis