Haematological manifestations of malaria and other parasitic diseases.

A. Fleming

Clinics in Haematology

Abstract:

What problem does this paper attempt to address?

Removal of micron-scale microplastic particles from different waters with efficient tool of surface-functionalized microbubbles

Ming Zhang,Junhan Yang,Zhen Kang,Xinyou Wu,Linfeng Tang,Zhimin Qiang,Daoyong Zhang,Xiangliang Pan

DOI: https://doi.org/10.1016/j.jhazmat.2020.124095

IF: 13.6

2021-01-01

Journal of Hazardous Materials

Abstract:Microplastic (MP) contamination in water has garnered significantly global concerns. The MP removal particularly challenges when the particle size decreases to several microns and other contaminants co-exist. This study used the coagulative colloidal gas aphrons (CCGAs) to simultaneously remove the micron-scale MP particles (similar to 5 mu m in diameter) and dissolved organic matter (DOM). Carboxyl-modified poly-(methyl methacrylate) (PMMA) and unsurface-coated polystyrene (PS) were chosen as target MPs. Over 94% of PS particles and almost 100% of color were simultaneously removed with lower CCGA consumption than the scenarios with either contaminant in water. The PMMA removal was not as high as the PS removal since the HA polyanions could compete with the negatively-charged PMMA for CCGAs. High salinity reduced the removal of HA by changing its interfacial behaviors without impacting the MP separation. In river water or influent of wastewater treatment plant, the MP particles were almost completely eliminated whereas the DOM (tyrosine-like or tryptophan-like) was partially removed. The fluorescence quenching titration revealed that CCGAs preferably captured the free DOM and the DOM-coated MP particles through complexation interaction. The study denoted that the CCGA system could be a robust tool for efficiently and synergistically removing micron-scale MPs and DOM from different water matrixes.
Plasma-mediated aging process of different microplastics: Release of dissolved organic matter and formation of disinfection by-products

Liling Zhou,Renjie Ma,Chenghe Yan,Jinmeng Wu,Ying Zhang,Jian Zhou,Guangzhou Qu,Xiaoling He,Tiecheng Wang

DOI: https://doi.org/10.1016/j.seppur.2022.122143

IF: 8.6

2022-12-15

Separation and Purification Technology

Abstract:The release of dissolved organic matter (DOM) from microplastics (MPs) in the water environment under physical, chemical, and biological transformation has been widely concerned. However, the impacts of released DOM on the subsequent generation of chlorinated disinfection by-products (DBPs) are still unknown. In this study, the leaching behaviors of organic matter from four types of MPs by plasma treatment were investigated, with polystyrene (PS), polyvinyl chloride (PVC), polypropylene (PP), and polyethylene (PE) as the model MPs. The plasma treatment led to cracks, pits, and loose porous surfaces of MPs, and the C/O ratios of these four MPs significantly decreased. Simultaneously, the long-chain alkyl groups of the four MPs were weakened, and O-containing functional groups were introduced after the plasma treatment. As a result, the dissolved organic carbon (DOC) released from PP, PVC, PS, and PE after 120 min of plasma treatment were 4.35, 4.33, 5.09, and 14.0 mg L−1, respectively. The released conjugated organic compounds contained aromatic hydrocarbons and double bonds or hydroxyl groups, which were soluble microbial byproduct-like and humic acid-like substances. Trichloromethane (TCM) and dichloroacetic acid (DCAA) were the main DBPs in trihalomethanes (THMs) and haloacetic acids (HAAs). The DBPs in the four MPs filtrates were mainly HAAs, which reached 811.2, 780.2, 1234.7, and 420.7 μg L−1 in the PVC, PP, PE, and PS filtrates after 120 min of plasma treatment, respectively. Correlations among DBPs, UV–visible and fluorescence components of these four MPs were established. Overall, the released byproducts of MPs had the potential to be the precursors of DBPs, and thus their risks deserve more attention.

engineering, chemical
Dielectric Barrier Discharge Plasma for the Remediation of Microplastic-Contaminated Soil from Landfill.

Jingyuan Sima,Jun Wang,Jiaxing Song,Xudong Du,Fangfang Lou,Yuhan Pan,Qunxing Huang,Chengqian Lin,Qin Wang,Guangjie Zhao

DOI: https://doi.org/10.1016/j.chemosphere.2023.137815

IF: 8.8

2023-01-01

Chemosphere

Abstract:The huge amount of plastic waste accumulated in landfills has caused serious microplastic (MP) pollution to the soil environment, which has become an urgent issue in recent years. It is challenging to deal with the non -biodegradable MP pollutants in actual soil from landfills. In this study, a coaxial dielectric barrier discharge (DBD) system was proposed to remediate actual MP-contaminated landfill soil due to its strong oxidation ca-pacity. The influence of carrier gas type, applied voltage, and air flow rate was investigated, and the possible degradation pathways of MP pollutants were suggested. Results showed the landfill soil samples contained four common MP pollutants, including polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyvinyl chloride (PVC) with sizes ranging from 50 to 1500 mu m. The MP pollutants in the soil were rapidly removed under the action of reactive oxygen species (ROS) generated by DBD plasma. Under the air flow rate of 1500 mL min -1, the maximum remediation efficiency represented by mass loss reached 96.5% after 30 min treatment. Compared with nitrogen, when air was used as the carrier gas, the remediation efficiency increased from 41.4% to 81.6%. The increased applied voltage from 17.5 to 24.1 kV could also promote the removal of MP contaminants. Suf-ficient air supply was conducive to thorough removal. However, when the air flow rate reached 1500 mL min- 1 and continued to rise, the final remediation efficiency would be reduced due to the shortened residence time of ROS. The DBD plasma treatment proposed in this study showed high energy efficiency (19.03 mg kJ-1) and remediation performance (96.5%). The results are instructive for solving MP pollution in the soil environment.
Efficient degradation of polystyrene microplastic pollutants in soil by dielectric barrier discharge plasma

Jingyuan Sima,Jun Wang,Jiaxing Song,Xudong Du,Fangfang Lou,Youqi Zhu,Jiahui Lei,Qunxing Huang

DOI: https://doi.org/10.1016/j.jhazmat.2024.133754

IF: 13.6

2024-02-24

Journal of Hazardous Materials

Abstract:In this study, the atmospheric dielectric barrier discharge (DBD) plasma was proposed for the degradation of polystyrene microplastics (PS-MPs) for the first time, due to its ability to generate reactive oxygen species (ROS). The local temperature in plasma was found to play a crucial role, as it enhanced the degradation reaction induced by ROS when it exceeded the melting temperature of PS-MPs. Factors including applied voltage, air flow rate, and PS-MPs concentration were investigated, and the degradation products were analyzed. High plasma energy and adequate supply of ROS were pivotal in promoting degradation. At 20.1 kV, the degradation efficiency of PS-MPs reached 98.7% after 60 min treatment, with gases (mainly CO x , accounting for 96.4%) as the main degradation products. At a concentration of 1 wt%, the PS-MPs exhibited a remarkable conversion rate of 90.6% to CO x , showcasing the degradation performance and oxidation degree of this technology. Finally, the degradation mechanism of PS-MPs combined with the detection results of ROS was suggested. This work demonstrates that DBD plasma is a promising strategy for PS-MPs degradation, with high energy efficiency (8.80 mg/kJ) and degradation performance (98.7% within 1 h), providing direct evidence for the rapid and comprehensive treatment of MP pollutants.

environmental sciences,engineering, environmental
Relationship of histologic features to behavior of cystosarcoma phyllodes. Analysis of ninety‐four cases

H. Norris,H. Taylor

DOI: https://doi.org/10.1002/1097-0142(196712)20:12<2090::AID-CNCR2820201206>3.0.CO;2-L

IF: 6.9209

1967-12-01

Cancer

Abstract:The clinical and pathologic findings in 94 patients with cystosarcoma phyllodes were studied to determine which pathologic characteristics were related to clinical behavior. The neoplasm recurred in 28 patients and 15 patients (17%) died of metastatic cystosarcoma. Most recurrences occurred within 2 years of initial surgery and all patients who died of cystosarcoma did so within 6 years. No tumor less than 4 cm in diameter or having fewer than 3 mitotic figures per 10 hpf in the areas of greatest mitotic activity proved fatal. Other microscopic features associated with a low risk of recurrence or of death were pushing margins (one death in 39 examples) and minimal cytologic atypism of the stromal cells (two deaths in 30 examples). No one feature was wholly reliable and a clearcut separation of benign from malignant tumors could not be made. Although axillary lymph nodes were enlarged in 17% of patients, metastasis to them occurred in not more than three instances (one histologically proved) and therefore radical mastectomy or routine axillary lymph node dissection is not worthwhile. Wide local excision for small cystosarcomas and simple mastectomy for larger ones is recommended. In addition, low axillary dissection should be considered in patients having clinically enlarged axillary lymph nodes and tumors larger than 4 cm if there is marked atypism of stromal cells or high mitotic activity, as determined by microscopic evaluation of the cystosarcoma.
Microplastics in Water: A Review of Characterization and Removal Methods

Yun Li,Ping Chen,Yalan Tang,Yanjing Yang,Chengyun Zhou,Jiaqi Bu,Shian Zhong

DOI: https://doi.org/10.3390/su16104033

IF: 3.9

2024-05-11

Sustainability

Abstract:Microplastics (MPs), as an emerging persistent pollutant, exist and accumulate in the environment, which has garnered them considerable global attention. While the origin, dispersion, distribution, and impact of MPs have been extensively documented, the characterization and removal strategies for MPs present ongoing challenges. In this literature review, we introduce in detail the advantages and disadvantages of seven characterization methods, from macroscopic to microscopic, from visual observation to microscopic characterization, and discuss their scope of application. In addition, 12 treatment schemes were summarized from the three treatment directions of physics, chemistry, and biology, including filtration, adsorption, extraction, magnetic separation, oil film separation, Fenton oxidation, electrochemical oxidation, persulfate advanced oxidation, photocatalytic oxidation, coagulation, electrocoagulation, foam flotation, anaerobic–anoxic–aerobic activated sludge, enzymatic degradation, bacterial degradation, and fungal degradation. Additionally, we present a critical assessment of the advantages and drawbacks associated with these removal strategies. Building upon the findings of our research team, we propose a novel approach to degrade MPs, which combines three-dimensional electrocatalytic oxidation technology with persulfate advanced oxidation technology. This advanced oxidation technology achieves 100% degradation of antibiotics in water, can degrade large molecules into environmentally harmless small molecules, and should also be a very good strategy for the degradation of MPs. Compared with two-dimensional electrocatalytic technology, the degradation efficiency is higher and the degradation cost is lower This review intends to propel further advancements for addressing the issue of MP pollution.

environmental sciences,environmental studies,green & sustainable science & technology
Removal and Generation of Microplastics in Wastewater Treatment Plants: A Review

Zhenjia Xu,Xue Bai,Zhengfang Ye

DOI: https://doi.org/10.1016/j.jclepro.2021.125982

IF: 11.1

2021-01-01

Journal of Cleaner Production

Abstract:Wastewater treatment plants (WWTPs) are the primary recipients of microplastics (MPs), prior to their discharge into natural waterbodies. The aim of this article is to summarize the generation process of MPs and the efficiency of their removal by treatment technologies currently adopted by WWTPs, as well as the influence of sludge treatment on the fragmentation of MPs. WWTPs mainly remove MPs by means of adhesion, sedimentation, and filtration. The average removal efficiency of MPs is less than 90% and is affected by the choice of wastewater treatment process and the properties of MPs (such as the size, density and morphology). The secretion of biological enzymes by microbes and the metabolites of biofilm may promote the hydrolysis of microbial carrier materials, resulting in the release of endogenous MPs under shear force. Furthermore, during wastewater pumping, disinfection and sludge thermal hydrolysis treatment, MPs may form sub-micron-scale secondary MPs through mechanical, ultraviolet, ozone and thermal degradation processes. Processes such as thermal drying of sludge and lime stabilization have been found to lead to the fragmentation of MPs increase the specific surface area and number of MPs, leading to an increase in the potential ecological threat posed by MPs in sludge. Currently, the level of MP pollution throughout the environment is continually increasing. This review will help improve wastewater and sludge treatment processes, effectively reducing the risk of MPs entering the natural water bodies and soil through WWTPs. (c) 2021 Elsevier Ltd. All rights reserved.
Microplastics in a Municipal Wastewater Treatment Plant: Fate, Dynamic Distribution, Removal Efficiencies, and Control Strategies

Xuemin Lv,Qian Dong,Zhiqiang Zuo,Yanchen Liu,Xia Huang,Wei-Min Wu

DOI: https://doi.org/10.1016/j.jclepro.2019.03.321

IF: 11.1

2019-01-01

Journal of Cleaner Production

Abstract:Microplastic pollution has become emerging environmental concern around world. The wastewater treatment plants (WWTPs) are attributed to a major pathway for microplastics (MPs) to enter into aquatic environment. To understand the fate and control strategies of MPs in WWTPs, we investigated MPs at a full-scale WWTP, Eastern China, with two parallel wastewater treatment systems, i.e. oxidation ditch (OD) and membrane bioreactor (MBR) for case study. The influent MPs consisted of polyethylene terephthalate (PET, 47%), polystyrene (PS, 20%), polyethylene (PE, 18%) and polypropylene (PP, 15%). MP morphotypes dominated in fragments (65%) and fibers (21%), which mainly were PET, with limited films (12%) and foams (2%). Typical plastic microbeads were not observed. The dominant size of MPs was >500 mu m (40%) and 62.5-125 mu m (29%). MP concentrations increased across the treatment systems depends on facility of treatment process. Influent MPs were removed by 99.5% in MBR system versus 97% in OD system on the basis of plastic mass while 82.1% versus 53.6% on MP number. The removed MPs accumulated in sludge phase. MBR system has much higher MP removal efficiency than OD system, likely due to membrane filtration. The results suggest that the source control of MPs by eliminating MP fibers from laundry facilities, banning use of plastic microbeads, Styrofoam products and plastic bags and properly selecting WWTP treatment unit could significantly reduce the mass and number of MPs from WWTPs. (C) 2019 Elsevier Ltd. All rights reserved.
Microplastic remediation technologies in water and wastewater treatment processes: Current status and future perspectives

Yang Lu,Mei-Chun Li,Juhyeon Lee,Chaozheng Liu,Changtong Mei

DOI: https://doi.org/10.1016/j.scitotenv.2023.161618

2023-01-21

Abstract:Microplastics (MPs) are a type of contaminants produced during the use and disposal of plastic products, which are ubiquitous in our lives. With the high specific surface area and strong hydrophobicity, MPs can adsorb various hazardous microorganisms and chemical contaminants from the environment, causing irreversible damage to our humans. It is reported that the MPs have been detected in infant feces and human blood. Therefore, the presence of MPs has posed a significant threat to human health. It is critically essential to develop efficient, scalable and environmentally-friendly methods to remove MPs. Herein, recent advances in the MPs remediation technologies in water and wastewater treatment processes are overviewed. Several approaches, including membrane filtration, adsorption, chemically induced coagulation-flocculation-sedimentation, bioremediation, and advanced oxidation processes are systematically documented. The characteristics, mechanisms, advantages, and disadvantages of these methods are well discussed and highlighted. Finally, the current challenges and future trends of these methods are proposed, with the aim of facilitating the remediation of MPs in water and wastewater treatment processes in a more efficient, scalable, and environmentally-friendly way.

environmental sciences
Transport of degradable/nondegradable and aged microplastics in porous media: Effects of physicochemical factors

Jiao Fei,Haoyuan Xie,Yifan Zhao,Xuerong Zhou,Huimin Sun,Nong Wang,Jun Wang,Xianqiang Yin

DOI: https://doi.org/10.1016/j.scitotenv.2022.158099

2022-12-10

Abstract:The degradable properties of degradable plastics allow them to form microplastics (MPs) faster. Therefore, degradable MPs may easily be transported in the underground environment. Research on degradable MPs transport in porous media is necessary and urgent. In this study, polylactic acid (PLA) and polyvinyl chloride (PVC) were selected to compare the transport differences between degradable and nondegradable MPs under different factors (flow rates, ionic strengths (ISs), pH, and coexisting cations) through column experiments, and UV irradiation was used to further simulate the effect of aging on different types of MPs. Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) were used to characterize functional groups and to determine the surface elements of MPs, respectively. The results showed that MPs were more mobile at higher flow rate, lower IS, higher pH, and monovalent cations. The order of transport capacity of MPs was PVC < aged PVC < PLA < aged PLA. This result was mainly attributed to the more negative Zeta potential and higher dispersion stability of aged PLA and PLA, which were caused by abundant O-functional groups. Compared with PVC, the O/C ratio of PLA increased significantly after aging, indicating that PLA was more prone to aging. The advection-dispersion-equation (ADE) fitted the transport data of MPs well. The interaction energy of MPs and quartz sand was accurately predicted by the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. This work contributes to a comprehensive understanding of the transport of degradable MPs in the environment.

environmental sciences
Occurrence and fate of microplastics from a water source to two different drinking water treatment plants in a megacity in eastern China

Ziwei Han,Jiali Jiang,Qing Xia,Chicheng Yan,Changzheng Cui

DOI: https://doi.org/10.1016/j.envpol.2024.123546

IF: 8.9

2024-02-23

Environmental Pollution

Abstract:The widespread presence of microplastics (MPs) contamination in drinking water has raised concerns regarding water safety and public health. In this study, a micro-Raman spectrometer was used to trace the occurrence of MP transport from a water source to a drinking water treatment plant (DWTP)1 with an advanced treatment process and DWTP2 with a conventional treatment process and the contributions of different processes to the risk reduction of MPs were explored. Six types of MPs were detected: polyethylene terephthalate, polyethylene, polypropylene, polystyrene, polyamide, and polyvinyl chloride. 2–5 μm (35.8–41.2%) and polyethylene terephthalate (27.1–29.9%) were the most frequently detected MP sizes and types of water source samples, respectively. The abundance of MPs in treated water decreased by 72.7–83.0% compared to raw water. Ozonation and granular activated carbon (52.7%), and sand filtration (47.5%) were the most effective processes for removing MPs from DWTP1 and DWTP2, respectively. Both DWTPs showed significant removal effects on polyethylene terephthalate, with 80.0–88.1% removal rates. The concentrations of polystyrene increase by 30.0–53.4% after chlorination. The dominant components in the treated water of DWTP1 and DWTP2 were polypropylene (24.7%) and polyethylene 27.7%, respectively, and MPs of 2–5 μm had the highest proportion (55.3–64.3%). Pollution load index and potential ecological risk index of raw water treated by DWTPs were reduced by 48.0–58.7% and 94.5–94.7%, respectively. The estimated daily intake of MPs in treated water for infants was 45.5–75.0 items/kg/d, respectively, approximately twice that of adults. This study contributes to the knowledge gap regarding MP pollution in drinking water systems.

environmental sciences
Microplastics in aquatic systems: An in-depth review of current and potential water treatment processes

Wang Biao,N Awanis Hashim,Mohamad Fairus Bin Rabuni,Ong Lide,Aubaid Ullah

DOI: https://doi.org/10.1016/j.chemosphere.2024.142546

IF: 8.8

Chemosphere

Abstract:Plastic products, despite their undeniable utility in modern life, pose significant environmental challenges, particularly when it comes to recycling. A crucial concern is the pervasive introduction of microplastics (MPs) into aquatic ecosystems, with deleterious effects on marine organisms. This review presents a detailed examination of the methodologies developed for MPs removal in water treatment systems. Initially, investigating the most common types of MPs in wastewater, subsequently presenting methodologies for their precise identification and quantification in aquatic environments. Instruments such as scanning electron microscopy, dynamic light scattering, Fourier transform infrared spectroscopy, Raman spectroscopy, surface-enhanced Raman spectroscopy, and Raman tweezers stand out as powerful tools for studying MPs. The discussion then transitions to the exploration of both existing and emergent techniques for MPs removal in wastewater treatment plants and drinking water treatment plants. This includes a description of the core mechanisms that drive these techniques, with an emphasis on the latest research developments in MPs degradation. Present MPs removal methodologies, ranging from physical separation to chemical and biological adsorption and degradation, offer varied advantages and constraints. Addressing the MPs contamination problem in its entirety remains a significant challenge. In conclusion, the review offers a succinct overview of each technique and forwards recommendations for future research, highlighting the pressing nature of this environmental dilemma.
Pennella filosa (L., 1758) (Copepoda: Siphonostomatoida) from the escolar Lepidocybium flavobrunneum (Smith, 1849) in the north-west Atlantic

G. Benz,W. E. Hogans

DOI: https://doi.org/10.1007/BF00009219

1993-10-01

Systematic Parasitology

Abstract:
Effects of UV-based oxidation processes on the degradation of microplastic: Fragmentation, organic matter release, toxicity and disinfection byproduct formation

Zhenqi Du,Guifang Li,Shunke Ding,Wuchang Song,Mengyu Zhang,Ruibao Jia,Wenhai Chu

DOI: https://doi.org/10.1016/j.watres.2023.119983

2023-06-15

Abstract:The occurrence and transformation of microplastics (MPs) remaining in the water treatment plants has recently attracted considerable attention. However, few efforts have been made to investigate the behavior of dissolved organic matter (DOM) derived from MPs during oxidation processes. In this study, the characteristics of DOM leached from MPs during typical ultraviolet (UV)-based oxidation was focused on. The toxicity and disinfection byproduct (DBP) formation potentials of MP-derived DOM were further investigated. Overall, UV-based oxidation significantly enhanced the aging and fragmentation of highly hydroscopic MPs. The mass scales of leachates to MPs increased from 0.03% - 0.18% at initial stage to 0.09% - 0.71% after oxidation, which were significantly higher than those leached by natural light exposure. Combined fluorescence analysis with high resolution mass spectrometer scan confirmed that the dominant MP-derived DOM are chemical additives. PET-derived DOM and PA6-derived DOM showed inhibition of Vibrio fischeri activity with corresponding EC50 of 2.84 mg/L and 4.58 mg/L of DOC. Bioassay testing with Chlorella vulgaris and Microcystis aeruginosa showed that high concentrations of MP-derived DOM inhibited algal growth by disrupting the cell membrane permeability and integrity. MP-derived DOM had a similar chlorine consumption (1.63 ± 0.41 mg/DOC) as surface water (1.0 - 2.0 mg/DOC), and MP-derived DOM mainly served as precursors for the investigated DBPs. Contrary to the results of previous studies, the DBP yields from MP-derived DOM were relatively lower than those of aquatic DOM under simulated distribution system conditions. This suggests that MP-derived DOM itself rather than serving as DBP precursor might be potential toxic concern.
Microplastic removal in conventional drinking water treatment processes: Performance, mechanism, and potential risk

Sang-Heon Na,Min-Ji Kim,Jun-Tae Kim,Seongpil Jeong,Seunghak Lee,Jaeshik Chung,Eun-Ju Kim

DOI: https://doi.org/10.1016/j.watres.2021.117417

2021-09-01

Abstract:The effectiveness of traditional drinking water treatment plants for the removal of Microplastics (MPs) in the size range of tens of micrometers is currently uncertain. This study investigated the behavior and removal efficiency of four different sized polystyrene MPs (10-90 μm in diameter) in a simulated cascade of coagulation/sedimentation, sand filtration, and UV-based oxidation over technically relevant time frames. In the coagulation and sand filtration steps, the larger the MP size, the better it was removed. The coagulant type and water characteristics (i.e., pH and the presence of natural organic matter) influenced the coagulation efficiency for MPs. X-ray microcomputed tomography technique and two-site kinetic modeling were used to identify the mechanisms involved in sand filtration. The MPs > 20 μm could be completely retained in sand by straining, while the attachment to the sand surface was likely responsible for the retention of MPs < 20 μm. However, approximately 16% of 10 μm MPs injected passed through the sand, which were further fragmented by UV oxidation. UV/H2O2 treatment promoted the MP fragmentation and chemical leaching more significantly than UV treatment, resulting in a higher toxicity for UV/H2O2-treated water. Our findings pave the way for deeper understanding of how MPs behave and transform in a sequential drinking water treatment process.
Fragmentation of microplastics in the drinking water treatment process - A case study in Yangtze River region, China

Junyi Wu,Yan Zhang,Yu Tang

DOI: https://doi.org/10.1016/j.scitotenv.2021.150545

2022-02-01

Abstract:Microplastics (MPs) are the emerging pollutants in the fresh water and have been found in the drinking water. Drinking water treatment plant (DWTP) is an important barrier to ensure the safety and quality of drinking water, so their effectiveness in removing MPs needs to be evaluated and optimized. In this paper, the abundance, characteristics and removal performance of 5 μm-5 mm granular MPs and 100 μm-5 mm fibrous MPs in the effluent of each water treatment unit in a DWTP in China were analyzed. The results show that only 80.96% of MPs ≤ 20 μm, accounting for more than 98% in the raw water, could be removed in the DWTP, while over 99% of the removal efficiency could be achieved for MPs > 20 μm. Coagulation-sedimentation and micro-flocculation combined with sand filtration couldn't effectively remove the granular MPs ≤ 20 μm (42.8% and 25.8%, respectively), but biological activated carbon (BAC) filtration was prone to remove this part (63.8%). Significant increases of granular MPs ≤ 20 μm were observed in the effluents of biological treatment (+149.6%) and ozonation (+13.8%). According to the variation in separate MPs' size distribution, the increases in MPs were attributed to the fragmentation of MPs, on which ozonation showed a remarkable effect. The ozonation might accelerate the aging and embrittlement of MPs, and then external stresses could further break them into smaller pieces, which eventually lead to an increase in MPs. To deal with the stubborn part and fragmentation of MPs in water, the removal ability of DWTP for MPs ≤ 20 μm needs to be improved. This study provides a detailed proof for the fate of MPs in the DWTP, and the results indicate that the fragmentation of MPs and the removal rate of MPs ≤ 20 μm should draw more attention in the DWTP.

environmental sciences
Photochlorination-induced degradation of microplastics and interaction with Cr(VI) and amlodipine

Peng Liu,Xiaowei Wu,Suyi Pan,Jiamin Dai,Zixuan Zhang,Xuetao Guo

DOI: https://doi.org/10.1016/j.scitotenv.2022.155499

2022-08-01

Abstract:Wastewater treatment plants (WWTPs) are the important source of microplastics (MPs) in the environment, and disinfection processes bear high potential to degrade MPs. This study investigated the physicochemical degradation, dissolved organic products and interaction with co-existed pollutants (heavy metal and pharmaceutical) on polyethylene (PE), polypropylene (PP) and polystyrene (PS) MPs during simulated disinfection processes. Compared to photo or chlorination, photochlorination significantly resulted in the physicochemical degradation, including morphology alteration, fragmentation, and chemical oxidation on PP and PS MPs, but showed relatively low effect on PE, indicating the different resistance among polymers to disinfected treatment. Photochlorination also caused the formation of chain-scission organic compounds and even chlorinated products from MPs (e.g. C11H19O4Cl for PP and monochlorophenol, dichlorophenol, chloroacetophenone and chlorobenzoic acid for PS), which may form disinfection byproducts to induce healthy risk. The adsorption potentials of MPs for Cr(VI) or amlodipine were enhanced by photochlorination since the cracking and formed oxygen functional groups enhanced the pore filling and surface precipitation of Cr(VI), and the electrostatic attraction and hydrogen bonding with amlodipine. The findings indicated the physicochemical degradation of MPs and the combined pollution with co-existed pollutants, highlighting the health risks of MP-derived organic products during the disinfection treatments (even in normal dosage) in WWTPs.

environmental sciences
Microplastic-derived dissolved organic matter: Generation, characterization, and environmental behaviors

Xigui Liu,Liping Fang,Jorge L Gardea-Torresdey,Xiaoxia Zhou,Bing Yan

DOI: https://doi.org/10.1016/j.scitotenv.2024.174811

2024-10-20

Abstract:Microplastics (MPs) represent a substantial and emerging class of pollutants distributed widely in various environments, sparking growing concerns about their environmental impact. In environmental systems, dissolved organic matter (DOM) is crucial in shaping the physical, chemical, and biological processes of pollutants while significantly contributing to the global carbon budget. Recent findings have revealed that microplastic-derived dissolved organic matter (MP-DOM) constitutes approximately 10 % of the DOM present on the ocean surface, drawing considerable attention. Hence, this study's primary objective is to explore, the generation, characterization, and environmental behaviors of MP-DOM. The formation and characteristics of MP-DOM are profoundly influenced by leaching conditions and types of MPs. This review delves into the mechanisms of the generation of MP-DOM and provides an overview of a wide array of analytical techniques, including ultraviolet-visible (UV-Vis) spectroscopy, fluorescence spectroscopy, Fourier transform infrared spectroscopy (FTIR), and mass spectroscopy, used to assess the MP-DOM characteristics. Furthermore, this review investigates the environmental behaviors of MP-DOM, including its impacts on organisms, photochemical processes, the formation of disinfection by-products (DBPs), adsorption behavior, and its interaction with natural DOM. Finally, the review outlines research challenges, perspectives for future MP-DOM research, and the associated environmental implications.
Potential Disinfection Byproducts-Related Risks to Drinking Water? Molecular Insights into the Dissolved Organic Matter from Photodegradation of Polyethylene Microplastics

Yanan Chen,Yunkun Qian,Dong An,Fan Liu,Jes Vollertsen,Jay Gan

DOI: https://doi.org/10.1021/acsestwater.3c00549

2023-01-01

ACS ES&T Water

Abstract:Microplastics (MPs) are constantly exposed to sunlight and release dissolved organic matter (DOM) from photodegradation. However, the molecular composition and transformation of such DOM remain unclear, particularly in process engineering like drinking water treatment. We deciphered the molecular characteristics of the DOM leached from MPs and, further, the potential contribution to the formation of disinfection byproducts (DBPs). The leached DOM was dominantly composed of the low molecular weight fraction (<1k Da), which contributed the most to DBP formation, challenging water treatment employing UV and chlorine disinfection. Chain scission and oxidation led to oligomer structures in leachates that were mainly distributed in the range C10-C21 with an incorporated number of oxygen atoms between 1 and 10. The DOM exhibited low O/C-wa (0.31-0.39) and high H/C-wa (1.54-1.69) ratios and became more saturated with increased exposure time. The leached DOM with such characteristics may not be efficiently removed by activated carbon or coagulation, which enriches the formation of DBPs. Information on the molecular composition of MP-derived DOM and the potential of the individual molecular weight fractions as precursors of DBPs is valuable for assessing the potential contribution of MPs to DBP-related risks in drinking water and identifying potential mitigation strategies.
Ultraviolet-C and vacuum ultraviolet inducing surface degradation of microplastics

Jialing Lin,Deyi Yan,Jianwei Fu,Yuheng Chen,Huase Ou

DOI: https://doi.org/10.1016/j.watres.2020.116360

IF: 12.8

2020-11-01

Water Research

Abstract:Wastewater treatment plants (WWTPs) are considerable microplastics (MPs) contributors to environmental waters. Knowledge about the MPs degradation process under ultraviolet irradiation was crucial to understanding the fate of MPs during and after water disinfection. In this study, surface alternations of polystyrene (PS), polyethylene (PE), polyvinylchloride (PVC) and polyethylene terephthalate (PET) under 254 nm (UV-C) and 185/254 nm (vacuum ultraviolet, VUV) irradiation were estimated. One-way treatment of MPs by UV or VUV with the recommended dose for WWTPs (USEPA, ~180 mJ cm−2) had little effect. In contrast, excessive exposure under twenty-times doses irradiation (3600 mJ cm−2) resulted in significant alternations on surface morphology, chemical feature and hydrophobicity. Noticeably morphology alterations, including cracks, wrinkles and protuberances, were observed for PS, PVC and PET, while PE was relatively resistant. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy revealed that UV irradiation induced cleavage of chemical bonds. Besides, simultaneous radical oxidation was predominant during VUV treatment, which contributed to the increasing generation of oxygen bonds, such as CO and CO, on all MPs surfaces. Drastic decreases of contact angle (> 20°) were observed for PS, PVC and PET even after 180 mJ cm−2 UV irradiation, indicating the UV disinfection in WWTPs can easily change their surface hydrophobicity. All these alternations weakened the adsorption capacity of non-polar benzene and polar ciprofloxacin on MPs. Generally, regular dose UV and VUV irradiation in water treatment disinfection can only induce slight effects on MPs surface characteristics and adsorption performance, while extreme dose irradiation can induce a potential reducing risk of organic contaminants migration along with MPs.

environmental sciences,engineering, environmental,water resources

Haematological manifestations of malaria and other parasitic diseases.

Removal of micron-scale microplastic particles from different waters with efficient tool of surface-functionalized microbubbles

Plasma-mediated aging process of different microplastics: Release of dissolved organic matter and formation of disinfection by-products

Dielectric Barrier Discharge Plasma for the Remediation of Microplastic-Contaminated Soil from Landfill.

Efficient degradation of polystyrene microplastic pollutants in soil by dielectric barrier discharge plasma

Relationship of histologic features to behavior of cystosarcoma phyllodes. Analysis of ninety‐four cases

Microplastics in Water: A Review of Characterization and Removal Methods

Removal and Generation of Microplastics in Wastewater Treatment Plants: A Review

Microplastics in a Municipal Wastewater Treatment Plant: Fate, Dynamic Distribution, Removal Efficiencies, and Control Strategies

Microplastic remediation technologies in water and wastewater treatment processes: Current status and future perspectives

Transport of degradable/nondegradable and aged microplastics in porous media: Effects of physicochemical factors

Occurrence and fate of microplastics from a water source to two different drinking water treatment plants in a megacity in eastern China

Microplastics in aquatic systems: An in-depth review of current and potential water treatment processes

Pennella filosa (L., 1758) (Copepoda: Siphonostomatoida) from the escolar Lepidocybium flavobrunneum (Smith, 1849) in the north-west Atlantic

Effects of UV-based oxidation processes on the degradation of microplastic: Fragmentation, organic matter release, toxicity and disinfection byproduct formation

Microplastic removal in conventional drinking water treatment processes: Performance, mechanism, and potential risk

Fragmentation of microplastics in the drinking water treatment process - A case study in Yangtze River region, China

Photochlorination-induced degradation of microplastics and interaction with Cr(VI) and amlodipine

Microplastic-derived dissolved organic matter: Generation, characterization, and environmental behaviors

Potential Disinfection Byproducts-Related Risks to Drinking Water? Molecular Insights into the Dissolved Organic Matter from Photodegradation of Polyethylene Microplastics

Ultraviolet-C and vacuum ultraviolet inducing surface degradation of microplastics