Abstract:The utilization of laser shock peening (LSP) in laser powder bed fused (LPBF) stainless steel (SS) 316L components enhances the mechanical characteristics and operational lifespan of the product quality through a significant reduction of residual stress and a noticeable increase in roughness parameters. The key objective of the study is to analyze the influence of consecutive laser shock peening (LSP) without ablative coating and low pulse energy on the surface properties, residual stress distribution, and microhardness of samples produced by LPBF with SS316L material. The surface quality of the sample subjected to consecutive laser shock peening shows a slight deterioration in its condition. This can be attributed to the combined impact of ablative surface and surface damage resulting from the production of high-energy plasma. However, the implementation of successive LSP results in a distinctive enhancement of compressive residual stresses (CRS) that are evenly distributed throughout the central axis and sharp edges. In contrast, the as-built condition exhibits non-uniform stress magnitudes. CRS observed in each LSP iteration exhibits a notable increase, reaching a maximum magnitude of -389 MPa compared to the initial stress level of 165 MPa in the as-built sample. This enhancement can be attributed to the repetitive impact of shock waves on the surface, leading to the formation of plastic deformation. The refinement of surface grains and the presence of favorable residual stresses were proven by the utilization of X-ray diffraction (XRD) studies and the Cos α plot. The XRD investigation also indicated the absence of any newly formed phases or secondary phases. A significant enhancement in microhardness was observed, with an increase of 58.3% achieved after the third consecutive peening process. The successive LSP samples displayed a gradual improvement in electrochemical behavior. Though the amplitude parameters increased after LSP, the increase in wear rate was observed.

Fatigue and Corrosion Evaluation of L-PBF 316L Stainless Steel Having Undergone a Self-Terminating Etching Process for Surface Finish Improvement

Effect of Microstructure and Dislocation Density on Material Removal and Surface Finish of Laser Powder Bed Fusion 316L Stainless Steel Subject to a Self-Terminating Etching Process

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Modification of surface characteristics and electrochemical corrosion behavior of laser powder bed fused stainless-steel 316L after laser polishing

Remarkably enhanced corrosion performance of 316 L stainless steel via laser powder bed fusion thin-layer deposition

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Post-Processing Effect on the Corrosion Resistance of Super Duplex Stainless Steel Produced by Laser Powder Bed Fusion

Effect of heat treatment and electroless Ni-P coating on mechanical property and corrosion behaviour of 316L stainless steel fabricated by laser powder bed fusion

Laser Powder Bed Fusion of 316L Stainless Steel: Effect of Laser Polishing on the Surface Morphology and Corrosion Behavior

Effect of Laser Shock Peening on Electrochemistry and Wettability of Additively Manufactured Stainless Steel

Microstructure, corrosion behavior, and fatigue resistance of laser powder bed fusion-produced precipitation-hardening martensitic M789 stainless steel

Effect of Heat Treatment on Fatigue Performance of 316L Stainless Steel Fabricated by Laser Powder Bed Fusion

Two-Steps Electrochemical Polishing of Laser Powder Bed Fusion 316L Stainless Steel

The impact of successive laser shock peening on surface integrity and residual stress distribution of laser powder-bed fused stainless steel 316L

The Effect of Severe Shot Peening on Fatigue Life of Laser Powder Bed Fusion Manufactured 316L Stainless Steel

Stress corrosion cracking performance of LPBF-built 316L stainless steel post-processed with heat treatment and severe shot peening

Enhancement of Fatigue Strength of 316L Austenitic Stainless Steel using Sand Blasting

On the Optimization of Roughness and Corrosion Resistance of Laser Beam Powder Bed Fusion Fabricated Ti–6Al–4V Parts—An Electrochemical Approach

Study on the effect of solution treatment on mechanical and corrosion properties of SAF 2507DSS produced by LPBF

Corrosion resistance of 3D printed SS316L post-processed by ultrasonic shot peening at optimum energy level

Surface Treatment and Corrosion Behavior of 316L Stainless Steel Fabricated by Selective Laser Melting