Behavioral pediatrics in office practice.

G. Prazar,E. Charney

DOI: https://doi.org/10.3928/0090-4481-19800601-06

1980-06-01

Pediatric Annals

Abstract:

What problem does this paper attempt to address?

Accurate Fault Location Method for Multiple Faults in Transmission Networks Using Travelling Waves

Yixiang Xia,Zewen Li,Yanhui Xi,Guorui Wu,Weixin Peng,Lizhi Mu

DOI: https://doi.org/10.1109/tii.2024.3371998

IF: 12.3

2024-01-01

IEEE Transactions on Industrial Informatics

Abstract:To prevent the further escalation of multiple faults in transmission networks, which could lead to severe accidents, this article proposes an accurate fault location method for multiple faults using simulated virtual faults (VFs) traveling waves. The method is validated by comparing it with real faults wavefront sequences. Initially, the article analyzes the interactions and aliasing phenomena of traveling waves from different fault sources at measurement points based on their propagation characteristics. It also discusses the relative temporal and amplitude relationships between different fault wavefront sequences. Then, a matching method between VF wavefront sequences and real fault wavefront sequences is proposed, and a wavefront sequence matching ratio is formulated to quantify the location disparity between the VFs and real faults. Finally, the article introduces a multiple faults location mechanism and achieves accurate fault location for multiple faults using the dynamic virtual faults traveling wave location method. Verified through the PSCAD simulation platform, the proposed method is unaffected by errors in wave propagation speed, eliminates the need for terminal traveling wave measuring equipment, and can accurately locate up to three faults with a location error less than 100 m.

automation & control systems,computer science, interdisciplinary applications,engineering, industrial
A novel traveling wave fault location method for transmission network based on time linear dependence

Kun Yu,Jupeng Zeng,Xiangjun Zeng,Feng Liu,Yarui Zu,Quan Yu,Chao Zhuo

DOI: https://doi.org/10.1016/j.ijepes.2020.106608

2021-03-01

Abstract:<p>Transmission network faults may not be located accurately in some abnormal conditions, such as traveling wave location device faults, startup failure and time recording error. In order to improve them, a novel traveling wave fault location method based on time linear dependence is proposed. The proximal point optimization algorithm (PPOA) is used to find the shortest transmission path of fault traveling wave. The linear fitting between the arrival time of the traveling wave head recorded by each substation and the transmission distance is made on the Cartesian coordinate plane, according to the characteristic that the length of the shortest path is directly proportional to the traveling wave transmission time. The information fusion for the traveling wave arrival time at each substation is achieved by linear regression analysis to correct the error information. The accurate fault location is obtained direct by coordinate information of the intersection of the fitted line and the coordinate axis. Finally, the traveling wave location system based on this method has been successfully tested in Hunan Power Grid. PSCAD simulation and field test results prove that the proposed method can effectively reduce the recording error in the arrival time of the fault traveling wave at each substation while improving the reliability and accuracy of fault location.</p>

engineering, electrical & electronic
Enhanced and precise traveling wave fault location accuracy on transmission lines utilizing dual time of arrival

Nuradeen Aisar,Ruikun Mai,Wang Jungang,Anand Mal Lodha

DOI: https://doi.org/10.1007/s00202-024-02832-8

IF: 1.63

2024-11-16

Electrical Engineering

Abstract:This paper introduces an improved and precise two-end traveling wave-based fault location method on a transmission line which eliminates the need for both traveling wave velocity (TWV) and line parameters measurements. It relies solely on the arrival times of the fault current traveling wave for FL estimation in the two ends of the power system. Additionally, the method can estimate the TWV itself with high accuracy (up to 99.6%). Extensive simulations using PSCAD/EMTDC software on a 400 kV, 50 Hz, 300 km transmission line demonstrate the method's effectiveness, and the results obtained show high accuracy in fault distance estimation, with a maximum error of 0.03% for faults occurring within 140 km. Furthermore, the method performs well under various fault conditions, including high-resistance fault, varying fault inception angles, and even with noise present in the data. It was also validated on the WSCC 9-bus system, demonstrating rapid computational speed and robustness under varying operating conditions. The paper also discusses a technique to handle a system with a series compensation without compromising the algorithms performance. This method executes quickly, allowing for swift FL, while still maintaining high accuracy even when dealing with diverse operational conditions.

engineering, electrical & electronic
A non-contact current traveling wave fault location method for multi-terminal overhead power lines based on adaptive mathematical morphology

Patrick N. Ayambire,Qi Huang,Albert K. Awopone,Li Jian,Paul O. K. Anane,Olusola Bamisile,Zhenyuan Zhang

DOI: https://doi.org/10.1007/s00202-024-02495-5

IF: 1.63

2024-06-13

Electrical Engineering

Abstract:In this paper, a fault location method for a transmission network with multiple terminals is suggested. It is based on the use of tunnel magnetoresistive sensors installed at each terminal for the contactless measurement of the magnetic flux density generated by the initial traveling wave signals. The initial current traveling wave arrival time at each terminal is detected using the proposed scheme's adaptive mathematical morphological function. When a fault occurs in the network, the magnetic flux density sensed by the sensors at each terminal is processed and used to create a fault flux ratio matrix (FFRM) and a fault flux characteristic matrix. A technique for identifying zonal faults, branch faults, and fault points has been developed based on the developed fault flux ratio matrix (FFRM). A thorough examination of several fault situations was carried out using a modeled transmission network based on the PSCAD/EMTDC frequency-dependent model. The analysis covered different types of faults in the network, including the identification of zone faults, branch faults, and fault points. The identification of zonal faults and fault points under varying fault impedance and fault inception angle was also analyzed. The results show that the proposed method is robust and accurate.

engineering, electrical & electronic
A fault location scheme based on composite traveling wave with transients in adjacent fault-free lines

Pulin Cao,Xiaoxu Cheng,Yiming Han,Hongchun Shu,Yutang Ma,Lu Zhang,Hongda Tang,Bo Yang

DOI: https://doi.org/10.1016/j.ijepes.2023.109762

IF: 5.659

2024-01-15

International Journal of Electrical Power & Energy Systems

Abstract:As the speedy expansion of power gird, the traveling wave fault locator in substation may not always connect to newly added transmission lines in time, which reduces the effectiveness of fault locator. In this paper, an adjacent fault-free line based fault location scheme for newly additional line is proposed. Since the traveling wave from adjacent fault-free line results in severe difficulty for identification of traveling waves from faulty line, the time–frequency matrix is performed to screen traveling waves. Firstly, in order to remove the influence of waves from remote terminals of adjacent fault-free line, the current refraction coefficient is theoretically analyzed. Due to the negative refraction coefficient, traveling waves from remote terminals of adjacent fault-free line can be reduced by the proposed composite traveling wave. Secondly, the time–frequency matrices of composite traveling wave and original traveling wave is obtained by S-transform. Then, these matrices are applied to form ratio matrix which thoroughly eliminated waves from remote terminals of fault-free lines. Moreover, the robustness of the proposed fault location scheme is thoroughly validated by the simulation of PSCAD/EMTDC. Finally, the proposed fault location method has the great accuracy in simulation tests and field data test.

engineering, electrical & electronic
Novel travelling wave fault location approach for overhead transmission lines

Dong Wang,Jinzhi Liu,Mengqian Hou

DOI: https://doi.org/10.1016/j.ijepes.2023.109617

IF: 5.659

2023-11-05

International Journal of Electrical Power & Energy Systems

Abstract:Travelling wave fault location approach for overhead transmission line is widely applied in actual power grid, which has better fault location accuracy comparing with conventional power frequency data based method. However, travelling wave fault location approach is highly related to the frequency distortion phenomenon of travelling wave propagation velocity, which includes two parts: (i) the distortion caused by reflection and refraction phenomena of transformer substation and (ii) the attenuation caused by distributed resistance of transmission line. Therefore, aiming to improve the fault location accuracy, the paper contributes to two aspects: (i) the complete theoretical analysis of the distortion phenomenon of travelling wave signal and (ii) the improved travelling wave fault location approach considering distortion phenomenon. Eventually, based on PSCAD/EMTDC simulation tool, a typical 500 kV case study model is established to verify the fault location accuracy of proposed travelling wave fault location approach under the influences of fault type issue, fault location issue and grounding resistance issue.

engineering, electrical & electronic
Eliminating the Dependence of GPS or Communication Latency Estimation in Traveling Wave Based Double-Terminal Fault Location

Haozong Wang,Zhenkang Qi,Binshu Chen,Kaixin Zhang,Wenzhong Li,Qihuan Dong,Xinzhou Dong

DOI: https://doi.org/10.1109/tpwrd.2023.3288158

IF: 4.825

2023-01-01

IEEE Transactions on Power Delivery

Abstract:Double-terminal traveling wave-based fault location is one of the most reliable and accurate technologies for power transmission line fault location. However, existing methods require a global positioning system (GPS) or accurate communication latency estimation to synchronize data from the two terminals. In this study, we propose an innovative double-terminal traveling wave-based fault location method that is independent of either GPS or communication latency estimation. The basic principle of the proposed method is that the arrival time difference between initial surges could be roughly calculated through the angle of pre-fault phasors by artificially assigning surge arrival points as the time references. Therefore, an approximate fault distance is obtained. The error could be reduced by detecting the fault-point-reflected surge. Extensive simulation experiments were performed using PSCAD/EMTDC software to assess the performance of the proposed algorithm. The results showed that the proposed method is applicable to different fault circumstances and independent of GPS synchronization and communication latency estimation while maintaining accuracy close to those of state-of-the-art algorithms. Finally, hardware experiments were performed to assess the validity and practicability of the proposed method.
A Traveling Wave-Based Fault Location Method Employing VMD-TEO for Distribution Network

Liwei Xie,Longfu Luo,Yong Li,Yu Zhang,Yijia Cao

DOI: https://doi.org/10.1109/tpwrd.2019.2959188

IF: 4.825

2020-08-01

IEEE Transactions on Power Delivery

Abstract:In this paper, a traveling wave based fault location method is proposed for distribution networks. Before fault occurs, an intrinsic distance difference matrix (IDDM) is established based on the characteristics of traveling wave propagation and the topology of distribution network. After the fault, the initial fault traveling wave signals are decomposed into several intrinsic mode function (IMF) signals by variational mode decomposition (VMD), and the first IMF signal is analyzed by teager energy operator (TEO) to determine the arriving time of initial fault traveling waves. According to the double-ended traveling wave method and the arrival time of traveling wave at all recorders, a fault distance difference matrix (FDDM) is built. By comparing the difference between IDDM and FDDM, a fault branch determination matrix (FBDM) and the lateral index Q are used to locate the fault. The effectiveness of the proposed method is verified via EMTP/ATP simulations. Results show that the proposed method has a high fault location accuracy, and does not need that all terminals of lines are installed traveling wave recorders.

engineering, electrical & electronic
Novel Fault Locating Method Based on Synchronized Voltage Phasor

WANG Bo,JIANG Quanyuan,CHEN Xiaogang,CAO Yijia

DOI: https://doi.org/10.3321/j.issn:1000-1026.2009.11.007

2009-01-01

Abstract:A novel fault locating method for transmission network using synchronized voltage phasor is presented.Based on symmetrical component method and linear superposition principle,the additional positive sequence network after fault is established and the matching index on fault point is defined.Then the fault can be located by traversing searching method with this index.Because only synchronized voltage phasor is used,the fault locating accuracy of this method is not affected by saturation of current transformer,and only sparse PMUs(phasor measurements unit) are needed.Simulations carried out with PSCAD have shown that the proposed technique can locate short-fault point on any type of transmission network accurately and adaptively,with no influence from factors such as fault resistance,fault type and so on.
Fault Location on Branched Networks Using a New Traveling-Wave Algorithm

X. C. Jiang,D. Z. Wang,X. Q. Liu,Y. Ning

DOI: https://doi.org/10.1109/IHMSC.2016.266

2016-01-01

Abstract:Existing traveling-wave fault location algorithms perform poorly on branch networks. A new traveling-wave algorithm used to locate faults on branch networks is demonstrated in this paper. In order to detect the fault-induced transient, an improved transient detection technique based on Park's transformation is proposed. The proposed technique self-adapts to electrical noise level and retrieves the initial traveling wave arrival time at each branch terminal in a simpler way. The fault location algorithm is based on the time difference of arrival between different branches, therefore, for unambiguously locating a fault, It is required that the synchronized transient detection module is placed at each branch terminal. A 35-kV test system case study is performed. The algorithm is evaluated by means of variety faults in the 35-kV power network. The obtained results indicate that the algorithm is very effective and suitable for fault location of branch networks.
A Novel Single-Ended Traveling Wave Fault Location Method Based on Reflected Wave-Head of Adjacent Bus

Fei Xu,Xinzhou Dong

DOI: https://doi.org/10.1049/cp.2014.0048

2014-01-01

Abstract:As the single-ended traveling-wave fault location method is cost effective and no need for synchronization device, it has been widely researched and discussed. However, the major problem is the identification of the reflected wave-head caused by the fault point. The reflected surge from the adjacent bus usually has the same polarity as the real fault point's reflected wave-head, so a confusion is inevitable. In this paper, a novel single-ended traveling wave fault location approach is proposed. The new method contains two major step: firstly, a wave-head comparison method is used to identify the Adjacent Bus' Reflected Wave-head (ABRW) from the Real Fault-point's Reflected Wave-head (RFRW). And then the intervals between line-modal and ground-modal of both ABRWs and Initial Wave-heads (IWs) are used to give out the exact fault distance. A simulation system based on EMTP is built, and abundant simulation results have validated the effectiveness of the proposed method.
Novel travelling wave fault location principle based on frequency modification algorithm

Wei Chen,Dong Wang,Donghai Cheng,Feng Qiao,Ximei Liu,Mengqian Hou

DOI: https://doi.org/10.1016/j.ijepes.2022.108155

2022-10-01

Abstract:Travelling wave (TW) fault location principle is widely utilized on actual power transmission line, which has higher fault location accuracy than conventional algorithms. But, considering the TW fault location principle is generally implemented using TW front arrival time and transmission velocity, the fault location accuracy is high influenced by frequency distortion. Therefore, in order to enhance the fault location accuracy, a novel TW fault location principle is proposed based on frequency modification algorithm. Firstly, the frequency modification algorithm of TW front is studied. Secondly, the detailed calculation principle of system impedance and transmission line's wave impedance is proposed. Thirdly, the novel TW fault location principle based on modified frequency spectrum is described. Eventually, via PSCAD/EMTDC simulation software, a typical 500kV simulation model is constructed to validate the robustness of proposed TW fault location principle against fault type, grounding resistor and fault initial angle issues.

engineering, electrical & electronic
Fault Location Method in Power Network by Applying Accurate Information of Arrival Time Differences of Modal Traveling Waves

Rui Liang,Nan Peng,Lutian Zhou,Xiangzhen Meng,Yihua Hu,Yaochun Shen,Xue Xue

DOI: https://doi.org/10.1109/tii.2019.2903267

IF: 12.3

2020-05-01

IEEE Transactions on Industrial Informatics

Abstract:Faults may be generated in power networks as a result of bad weather, human activities, or some other factors. The complex structure of power network adds to the difficulty of fault location (FL). This paper presents a novel FL scheme by utilizing the information of the time differences of arrival (TDOAs) of modal traveling waves (MTWs) asynchronously sampled in the network. First, the fault area is determined by searching the minimum TDOA of MTWs. Then, by applying the fictitious fault point method in the fault area, the minimum accumulated difference is used to detect the fault line. Finally, the accurate FL is estimated by solving the objective function of the absolute distance between the FL and multiple FL candidates. Various simulations are carried out in the IEEE 30-bus system. The calculation results demonstrate that the method is not affected by fault impedance, inception angle, location, and noises to a certain extent.

automation & control systems,computer science, interdisciplinary applications,engineering, industrial
A Novel Current Travelling Wave Based Single-Ended Fault Location Method for Locating Single-Phase-to-ground Fault of Transmission Line

Aoyu Lei,Xinzhou Dong,Shenxing Shi,Bin Wang

DOI: https://doi.org/10.1109/upec.2015.7339950

2015-01-01

Abstract:Current travelling wave based single-ended fault location method needs to recognize the travelling waves propagating from the fault direction as well as the travelling wave reflected from the fault point or remote-end bus. This paper firstly compares the current travelling waves of the fault line and the longest health line connected to the local bus based on dyadic wavelet transform to obtain the current travelling waves propagating from the fault direction. Secondly, based on the cross transmission phenomenon of modal travelling waves under the scenario of single-phase-to-ground fault, the arrival sequence relation and the polarity relation of aerial-modal component and zero-to-aerial-modal component (i.e. cross transmission component) of the current travelling waves reflected from the fault point and the remote-end bus are investigated and the source of the second current travelling wave propagating from the fault direction is identified. Thirdly, the first and the second current travelling waves propagating from the fault direction are utilised to locate the single-phase-to-ground fault. Finally, a large number of EMTP based simulation cases are used to test and validate the proposed fault location method.
Two-terminal traveling wave fault location based on successive variational mode decomposition and frequency-dependent propagation velocity

Ruochen Zeng,Qinghua Wu,Luliang Zhang

DOI: https://doi.org/10.1016/j.epsr.2022.108768

IF: 3.818

2022-12-01

Electric Power Systems Research

Abstract:This paper proposes a two-terminal traveling wave fault location method based on Successive Variational Mode Decomposition (SVMD) and frequency-dependent propagation velocity. Firstly, SVMD is used to extract all Intrinsic Mode Functions (IMFs) and their center frequencies of the aerial mode voltages in a successive manner. The maximum IMF with the highest center frequency is used for further processing. Secondly, The propagation velocity is obtained by frequency–velocity characteristic curve and the arrival time of traveling wavefront is determined by the normalized Teager Energy Operator (TEO). Finally, considering the time-domain and frequency-dependent characteristics of traveling wave, the fault distance is estimated by combining the arrival time, frequency and propagation velocity. PSCAD/EMTDC simulation results show that the proposed method achieves reliable and robust performance under different fault scenarios and outperforms compared existing methods.

engineering, electrical & electronic
Distribution System Fault Location Method Using Reclosure-generating Traveling Waves

Xinzhou Dong,Haozong Wang,Zeyu Xin,Shenxing Shi,Bin Wang

DOI: https://doi.org/10.1109/pesgm41954.2020.9281701

2020-01-01

Abstract:Fault location in distribution systems includes 2 subtasks: fault distance estimation and fault section identification. This paper presents a fault location method based on reclosure-generating traveling waves and system topology. Firstly, the reclosure-generating traveling waves under normal and fault conditions are analyzed to find the traveling wave reflected by fault point, through which the fault distance could be estimated. Secondly, we propose a fault section identification method by comparing real measured traveling waves with simulated traveling waves with different potential fault points. Noticing that only time information of traveling waves rather than their magnitude is necessary, instead of using electromagnetic transient simulation, we also present a simplified simulation algorithm that only focuses on the arrival time of traveling waves based on priority queue. Experiments demonstrate that the proposed method can locate fault points in high accuracy with low computational burden.
A Single-Ended Fault Location Method for Transmission Line Based on Full Waveform Feature Extraction of Traveling Waves

Feng Deng,Zhe Zeng,Yihan Zhong,Yarui Zu,Zhen Zhang,Yifei Huang,Sixu Feng,Xiangjun Zeng

DOI: https://doi.org/10.1109/tpwrd.2023.3248102

IF: 4.825

2023-08-01

IEEE Transactions on Power Delivery

Abstract:Conventional single-ended traveling wave fault location methods, which commonly depend on partial features of traveling wavefronts, may lead to fault location failure, especially for weak-signal faults such as high impedance or zero-crossing faults and close-in faults. To tackle it, this paper presents a fault location method according to the extracted panoramic features of traveling wave full waveform (TWFW) in time-frequency domains. Firstly, two rules of the TWFW features are probed, that is, the wavefront arrival sequence is varied from fault sections, as well as the frequency distribution of wavefronts is strongly related to the precise fault distance. Ergo, the mapping relationships between the TWFW and fault distance are qualitatively confirmed in order to demonstrate the uniqueness of the TWFW subsequently. Next, a LeNet-5-based convolution neural network (CNN) model is constructed to quantitatively evaluate such mapping relationships. In this model, various TWFW features will be extracted to the convolution channels when the CNN parameters are optimized adaptively, and the mapping relations can be formed in light of these sensitive features to estimate the fault distance. Finally, a Grad-CAM visualization method is deployed in the case study, and the accuracy along with the robustness of the proposed method in various fault conditions can be validated consequently.

engineering, electrical & electronic
A novel fault location method for hybrid lines based on traveling wave

Liwei Xie,Longfu Luo,Junjie Ma,Yong Li,Mingmin Zhang,Xiangjun Zeng,Yijia Cao

DOI: https://doi.org/10.1016/j.ijepes.2022.108102

2022-10-01

Abstract:In this paper, a novel fault traveling wave-based location method for hybrid lines is proposed. According to the refraction characteristics of fault traveling wave (TW) at junction nodes, the node ratio coefficient value Q is defined based on the amplitude of traveling wave. Then, by comparing the Q values of junction nodes and fault points, a fault section identification principle is proposed to determine the fault line section for hybrid lines. After identification of fault line section, a double-ended fault location method is revised via adding the location compensation factors to mitigate the effect of traveling wave velocity changes on fault location for multi-section hybrid lines. Additionally, considering the detection problems of arrival time for TW signals, the extreme-point symmetric mode decomposition (ESMD) method and Teager energy operator (TEO) are proposed. The ESMD method is applied to decompose the sampled fault traveling wave signals into several intrinsic modes to filter out the fundamental frequency and low frequency signals. The TEO is employed to track the characteristics of TW signals. Effectiveness of the proposed method is validated in PSCAD. Results show that the ESMD-TEO can detect TW signals effectively, and the proposed fault location method can determine the fault line section and locate fault positions correctly.

engineering, electrical & electronic
Design of fault location algorithm based on online distributed travelling wave for HV power cable

Chen Haohao,Li Jing,Chen Ping

DOI: https://doi.org/10.1371/journal.pone.0296513

IF: 3.7

2024-01-06

PLoS ONE

Abstract:To tackle the challenge of localization failure due to traveling wave dispersion during a mid-line fault in a long high-voltage cable, this study conducts an in-depth analysis of the refraction characteristics of the cumulative three-phase sheath currents at cross commutation points and direct grounding points, facilitated by detailed theoretical derivation. We introduce the novel concept of a 'first traveling wave attenuation index,' which quantifies the peak of the initial faulted traveling wave. We strategically place distributed traveling wave detection devices solely in the first direct grounding box of each cross-interconnected main section, effectively segmenting the line into five distinct zones. These zones are identified based on the unique transient polarities exhibited by the first traveling wave of fault current at each impedance mismatch point along the cable. To overcome the issue of weak traveling wave signals collected at the first end measurement point, we propose an innovative peak detection method for the first wave. This method harnesses the power of empirical wavelet transform (EWT) and multi-resolution singular value decomposition (MRSVD), providing a significant boost in ranging accuracy compared to traditional wavelet methods. Simulation results validate the efficacy of our proposed fault location method, which accurately pinpoints the fault section by contrasting the polarity of the first wave peak of the sheath current detected at each measurement point. Notably, our method ensures safety and convenience as the equipment does not require direct contact with high voltage.

multidisciplinary sciences
A novel fault location method for distribution networks with distributed generations based on the time matrix of traveling-waves

Liang Cheng,Tao Wang,Yi Wang

DOI: https://doi.org/10.1186/s41601-022-00265-8

IF: 10.5

2022-11-17

Protection and Control of Modern Power Systems

Abstract:Abstract To improve location speed, accuracy and reliability, this paper proposes a fault location method for distribution networks based on the time matrix of fault traveling waves. First, an inherent time matrix is established according to the normalized topology of the target distribution network, and a post-fault time matrix is obtained by extracting the head data of initial waves from traveling wave detection devices. A time determination matrix is then obtained using the difference operation between the two matrices. The features of the time determination matrix are used for fault section identification and fault distance calculation, to accurately locate faults. The method is modified by considering economic benefits, through the optimal configuration of detection devices of traveling waves when calculating fault distances. Simulation results show that the proposed method has good adaptation with higher fault location accuracy than two other typical ones. It can deal with faults on invalid branches, and the error rate is under 0.5% even with connected DGs.

energy & fuels,engineering, electrical & electronic

Behavioral pediatrics in office practice.

Accurate Fault Location Method for Multiple Faults in Transmission Networks Using Travelling Waves

A novel traveling wave fault location method for transmission network based on time linear dependence

Enhanced and precise traveling wave fault location accuracy on transmission lines utilizing dual time of arrival

A non-contact current traveling wave fault location method for multi-terminal overhead power lines based on adaptive mathematical morphology

A fault location scheme based on composite traveling wave with transients in adjacent fault-free lines

Novel travelling wave fault location approach for overhead transmission lines

Eliminating the Dependence of GPS or Communication Latency Estimation in Traveling Wave Based Double-Terminal Fault Location

A Traveling Wave-Based Fault Location Method Employing VMD-TEO for Distribution Network

Novel Fault Locating Method Based on Synchronized Voltage Phasor

Fault Location on Branched Networks Using a New Traveling-Wave Algorithm

A Novel Single-Ended Traveling Wave Fault Location Method Based on Reflected Wave-Head of Adjacent Bus

Novel travelling wave fault location principle based on frequency modification algorithm

Fault Location Method in Power Network by Applying Accurate Information of Arrival Time Differences of Modal Traveling Waves

A Novel Current Travelling Wave Based Single-Ended Fault Location Method for Locating Single-Phase-to-ground Fault of Transmission Line

Two-terminal traveling wave fault location based on successive variational mode decomposition and frequency-dependent propagation velocity

Distribution System Fault Location Method Using Reclosure-generating Traveling Waves

A Single-Ended Fault Location Method for Transmission Line Based on Full Waveform Feature Extraction of Traveling Waves

A novel fault location method for hybrid lines based on traveling wave

Design of fault location algorithm based on online distributed travelling wave for HV power cable

A novel fault location method for distribution networks with distributed generations based on the time matrix of traveling-waves