Abstract:The global massive consumption of disposable face masks driven by the ongoing COVID-19 pandemic has emerged as a blooming disaster to both the land and marine environment that might last for generations. Growing public concerns have been raised over the management and control of this new form of plastic pollution, and one of the proposed sustainable solution is to use renewable and/or biodegradable resources to develop mask materials in order to minimize their environmental impacts. As a representative biodegradable polymer, polylactic acid (PLA) has been proposed as a promising candidate to produce non-woven face masks instead of those fossil-based polymers. To further explore the feasibility of this alternative mask material, the present work aims to study both the hydrolytic and bio-degradation behaviors of pure PLA-derived 3-ply disposable face masks at ambient temperature. Hydrolytic degradability was investigated at different pH conditions of 2, 7 and 13 with the whole piece of face mask soaked for regular timed intervals up to 8 weeks. Weight loss study showed neutral and acidic conditions had minimal effect on PLA masks, but rapid degradation occurred under basic conditions in the first week with a sharp 25% decrease in weight that slowly tapered off, coupled with solution pH dropping from 13 to 9.6. This trend was supported by mechanical property, bacterial filtration efficiency (BFE) and particulate filtration efficiency (PFE) studies. Masks soaked in basic conditions had their modulus and tensile strength dropped by more than 50% after 8 weeks where the middle layer reached 68% and 90% respectively just after 48 h, and BFE and PFE decreased by 14% and 43% respectively after 4 weeks, which was much more significant than those in neutral and acidic conditions. Base degradation was also supported by nuclear magnetic resonance (NMR) and fourier transform infrared (FTIR), which disclosed that only the middle layer undergo major degradation with random chain scission and cleavage of enol or enolate chain ends, while outer and inner layers were much less affected. Scanning electron microscopy (SEM) attributed this observation to thinner PLA fibers for the middle layer of 3-7 mu m diameter, which on average is 3 times smaller. This degradation was further supported by gel permeation chromatography (GPC) which saw an increase in lower molecular weight fragment Mw similar to 800 Da with soaking duration. The biodegradation behavior was studied under OECD 301F specification in sewage sludge environment. Similarly, degradation to the middle meltblown layer was more extensive, where the average weight loss and carbon loss was 25.8% and 25.7% respectively, double that of outer/inner spunbond layer. The results showed that the face masks did not completely disintegrate after 8 weeks, but small solubilized fragments of PLA formed in the biodegradation process can be completely mineralized into carbon dioxide without generation of secondary microplastic pollution in the environment. PLA masks are therefore a slightly greener option to consider in times of a pandemic that the world was caught unprepared; however future research on masks could be geared towards a higher degradability material that fully breaks down into non-harmful components while maintaining durability, filtration and protection properties for users. (C) 2021 Published by Elsevier B.V.

The 3D-Printing-Accelerated Design for a Biodegradable Respirator from Tree Leaves (TRespirator)

Bioinspired Structures Made of Silicone Nanofilaments for Upcycling Waste Masks to Reusable N95 Respirators

Recycling polypropylene from non-woven disposable masks in developing a three-dimensional printing filament

3D Printed and Electrospun, Transparent, Hierarchical Polylactic Acid Mask Nanoporous Filter

Biodegradable and high-performance multiscale structured nanofiber membrane as mask filter media via poly(lactic acid) electrospinning

Disposal and resource utilization of waste masks: a review

Polylactic Acid Face Masks: Are These the Sustainable Solutions in Times of COVID-19 Pandemic?

Environmental risks of polymer materials from disposable face masks linked to the COVID-19 pandemic

Design of customizable personal protective equipment for 3-D printing: Performance evaluation of N95 respirators using computational fluid dynamics

Mechanical upcycling of single-use face mask waste into high-performance composites: An ecofriendly approach with cost-benefit analysis

Feasibility of biodegradable material polylactic acid as a substitute for polypropylene for disposable medical masks production verified by life cycle assessment

Fabrication of a High-Performance and Reusable Planar Face Mask in Response to the COVID-19 Pandemic

Distributed manufacturing: A case study in additive manufacturing face masks for the COVID-19 pandemic

Multi‐Scale Nanoarchitectured Fibrous Networks for High‐Performance, Self‐Sterilization, and Recyclable Face Masks

Antibacterial, antiviral, and biodegradable collagen network mask for effective particulate removal and wireless breath monitoring

3D printing of an advanced design emergency mechanical ventilator, in response to the COVID 19 pandemic

Harnessing the potential of regenerated bamboo knitted fabrics in development of eco-friendly masks

Insight into the microplastics release from disposable face mask: Simulated environment and removal strategy

Global face mask pollution: Threats to the environment and wildlife, and potential solutions

Poly(lactic acid)/artificially cultured diatom frustules nanofibrous membranes with fast and controllable degradation rates for air filtration

Saving 80% Polypropylene in Facemasks by Laser-Assisted Melt-Blown Nanofibers.