Abstract:PURPOSE: To evaluate the usefulness of ridge augmentation using a customized titanium mesh (CTM) that was preformed by trimming and bending the commercial titanium mesh on a virtually reconstructed 3D acrylic resin model using clinical, radiologic, histologic, and histomorphometric analyses.MATERIALS AND METHODS: This study was designed prospectively for patients who required vertical ridge augmentation using a staged approach before implant surgery. After installation of the CTM, grafting was performed using deproteinized porcine bone mineral covered with an absorbable membrane. Computed tomography was performed preoperatively and 6 months after simultaneous/staged guided bone regeneration to measure planned, reconstructed, and lacking bone volume, and the reconstruction rate was calculated based on these values. Clinical complications were also recorded, particularly the mesh exposure rate. At re-entry, the bone core was obtained using a trephine bur, and histologic and histomorphometric analyses were performed.RESULTS: A total of 10 sites in eight patients were used for the study analysis. The mean planned bone volume was 1.15 cm3 (range: 0.78 to 1.56 cm3), mean lacking bone volume was 0.13 cm3 (range: 0 to 0.59 cm3), and mean reconstructed bone volume was 1.02 cm3 (range: 0.56 to 1.43 cm3). The exposure rate was 30% (3 out of 10 sites). The reconstruction rate was over 80%, except for one case that showed suppuration. From histomorphometric analysis, 27.52% ± 16.87% of new bone, 7.62% ± 5.19% of residual graft, and 64.86% ± 23.76% of connective tissue were observed. The core biopsy samples demonstrated different pseudoperiosteum layer appearances based on the healing stage of the augmented sites. In the premature bone, the inner osteogenic layer consisted of multiple layers of osteoblast cells with adjacent large blood vessels. However, in the mature augmented site, there was no specific inner osteogenic layer, and the outer fibrous layer was dominant.CONCLUSIONS: The fabrication of CTM based on the application of the 3D-printing technique makes vertical ridge augmentation easier and can reduce complications and achieve target bone acquisition. In addition, it is expected that quantitative analysis of the pseudoperiosteum layer will be facilitated using the CTM.

Linear bone gain and healing complication rate comparative outcomes following ridge augmentation with custom 3D printed titanium mesh vs Ti-reinforced dPTFE. A randomized clinical trial

Complication, vertical bone gain, volumetric changes after vertical ridge augmentation using customized reinforced PTFE mesh or Ti-mesh. A non-inferiority randomized clinical trial

Assessment of the application of a novel three-dimension printing individualized titanium mesh in alveolar bone augmentation: A retrospective study

Vertical Ridge Augmentation with Customized Titanium Mesh Using a 3D-Printing Model: A Prospective Study in Humans

Dense Polytetrafluoroethylene Membrane versus Titanium Mesh in Vertical Ridge Augmentation: Clinical and Histological Results of a Split-mouth Prospective Study

Application of three-dimensional printing individualized titanium mesh in alveolar bone defects with different Terheyden classifications: A retrospective case series study

The Ti-Mesh Technique: Guided Bone Regeneration for Three-Dimensional Augmentations. Clinical Aspects: A Case Series

Clinical outcome of alveolar ridge augmentation with individualized CAD-CAM-produced titanium mesh

Clinical and Micro-CT analyses of Vertical Guided Bone Regeneration of Mandible using a d-PTFE Membrane, Autogenous Bone, and High-Temperature Processed Xenograft- A Case Series Study

CAD/CAM Titanium Meshes for GBR: A Case Series with Preliminary Histologic Analysis

Alveolar Ridge Preservation Using a Collagenated Xenograft: A Randomized Clinical Trial

Alveolar ridge reconstruction with titanium meshes: a systematic review of the literature

Histomorphometry of Bone after Intentionally Exposed Non-Resorbable d-PTFE Membrane or Guided Bone Regeneration for the Treatment of Post-Extractive Alveolar Bone Defects with Implant-Supported Restorations: A Pilot Randomized Controlled Trial

Comparison of Khoury's Bone Shell Technique vs Titanium-reinforced Polytetrafluoroethylene Membrane for 3D-bone Augmentation in Atrophic Posterior Mandible: A Randomized Clinical Trial

A 3D micro-CT assessment of composition and structure of bone tissue after vertical and horizontal alveolar ridge augmentation using CAD/CAM-customized titanium mesh

The Assessment of Volumetric Changes for Alveolar Ridge Preservation or Reconstruction by Three-dimensional Analysis at Posterior Extraction Sites with Severe Bone Defects Using DBBM-C Collagen Membrane and PRF: A Prospective and Randomized Clinical Trial

Half‐ and full‐grafting alveolar ridge preservation with different sealing materials: A three‐arm randomized clinical trial

Evaluation of Alveolar Ridge Dimensions by Socket Preservation Therapy Using a Bone Graft and Platelet-Rich Fibrin: A Randomized Controlled Trial

Horizontal-guided Bone Regeneration using a Titanium Mesh and an Equine Bone Graft

Three-dimensional analysis of bone remodeling following ridge augmentation of compromised extraction sockets in periodontitis patients: A randomized controlled study

Vertical-guided bone regeneration with a titanium-reinforced d-PTFE membrane utilizing a novel split-thickness flap design: a prospective case series