Die Continuität des Lebens als Grundlage der modernen biologischen Anschauung

R. Virchow

DOI: https://doi.org/10.1007/BF01924303

1897-10-01

Archiv für Pathologische Anatomie und Physiologie und für Klinische Medicin

Abstract:

What problem does this paper attempt to address?

Lignin-induced rapid-synthesis of deep eutectic solvent-based gel with high robustness and conductivity applied for flexible quasi-solid-state supercapacitors

Tianqi Li,Shaoning Wang,Yuefeng Huang,Huimei Zhou,Lili Zhang,Zhiguo Wang

DOI: https://doi.org/10.1016/j.cej.2023.144864

IF: 15.1

2023-09-01

Chemical Engineering Journal

Abstract:A novel rapid-synthesis method for the preparation of high-performance deep eutectic solvent (DES)-based gel was proposed for constructing flexible quasi-solid-state supercapacitors. The dynamic redox reaction between silver ions and lignin produced large amounts of free radicals, which triggered the polymerization of acrylic acid monomer (AA) to form silver-lignin nanoparticle/DES/Poly (acrylic acid) (Ag-L NPs/DES/PAA) composite gel. Ag-L NPs constructed a dynamic redox system that generated catechol groups, triggering rapid self-gelation of Ag-L NPs/DES/PAA at room temperature, while imparting long-term and repeatable adhesion ability to the hydrogel. In addition, DES, as the liquid component of Ag-L NPs/DES/PAA, not only provided a good solution system for lignin but also enhanced its electrochemical performance and stability. Thanks to the synergistic effects of DES and the dynamic transformation of lignin and silver, Ag-L NPs/DES/PAA not only exhibited a high conductivity of over 10 mS/cm, but also showed a remarkable adhesion strength of over 80 KPa. Moreover, the presence of lignin endowed Ag-L NPs/DES/PAA with more than 300% strain and over 350 KPa compression performance. A supercapacitor based on this assembly exhibited a high specific capacitance (208F g−1, 0.5 A g−1) and an impressive capacity retention rate of 92.05% after 3000 cycles. This research offered insightful information on the use of lignin in flexible electronics.

engineering, chemical, environmental
Enhancement of charge transport in interconnected lignin-derived carbon fibrous network for flexible battery-supercapacitor hybrid device

Man Zhou,Addie Bahi,Yaping Zhao,Liting Lin,Frank Ko,Peyman Servati,Saeid Soltanian,Ping Wang,Yuanyuan Yu,Qiang Wang,Zaisheng Cai

DOI: https://doi.org/10.1016/j.cej.2020.128214

IF: 15.1

2021-04-01

Chemical Engineering Journal

Abstract:Self-supporting and flexible carbon fibrous mats are promising electrode materials for wearable devices. The contact resistance between adjacent fibers is still a limit for further improvement of energy storage performance. Herein, an activated interconnected lignin-derived carbon fibrous network (AILCFN) is fabricated by electrospinning followed by heat treatment. The unique interconnected structure between fibers in AILCFN is designed by controlling the ratio of soft Kraft lignin fractions with different thermal mobility. While the interconnected fibers are benefited for the electron transport and conductive property of the carbon networks, the high specific surface area is synergistically conduced to the direct channels for the fast ion transfer. The as-prepared AILCFN-3 exhibits an excellent specific capacitance and a high rate capability (69% from the current density from 1 to 20 mA cm−2). Further, AILCFN-3 can act as the scaffold to support the electrodeposited Ni-Co-S nanosheets. The AILCFN/Ni-Co-S composite electrode displays a high specific capacity of 1140.0 C g−1 at a current density of 10 A g−1. The assembled AILCFN/Ni-Co-S//AILCFN-3 BSH exhibits a high energy density of 30.8 Wh kg−1 with a power density of 0.8 kW kg−1 and demonstrates both excellent cyclability and flexibility, attributed to the high effective specific surface area and advantageous interconnected structure. The self-powered system assembled onto a lab coat can continuously power for the electronic watch under sunlight illumination and dark environment, demonstrating the promising potential of AILCFN in future wearable electronics. This work represents a "waste into wealth" direction of conversion strategy from biomass waste lignin to value-added energy storage materials, which conversely turns different thermal property of lignin fractions to good account, and breaks through the application limits caused by the heterogeneity.

engineering, chemical, environmental
Dynamic Networks of Cellulose Nanofibrils Enable Highly Conductive and Strong Polymer Gel Electrolytes for Lithium‐Ion Batteries

Zhen Wang,Patrick Heasman,Jowan Rostami,Tobias Benselfelt,Mathieu Linares,Hailong Li,Artem Iakunkov,Farhiya Sellman,Rebecca Östmans,Mahiar Max Hamedi,Igor Zozoulenko,Lars Wågberg

DOI: https://doi.org/10.1002/adfm.202212806

IF: 19

2023-04-19

Advanced Functional Materials

Abstract:Dynamic networks of cellulose nanofibrils (CNFs) are utilized to create a gel electrolyte from an ultralow CNF fraction of 0.9%, which delivers a tensile strength of 0.75 ± 0.09 MPa and an ionic conductivity of 0.61 ± 0.12 mS cm−1 at room temperature, one of the highest records of polymer gel electrolytes. The water‐binding capacity of CNFs enhances ionic conductivity. Tunable dynamic networks of cellulose nanofibrils (CNFs) are utilized to prepare high‐performance polymer gel electrolytes. By swelling an anisotropically dewatered, but never dried, CNF gel in acidic salt solutions, a highly sparse network is constructed with a fraction of CNFs as low as 0.9%, taking advantage of the very high aspect ratio and the ultra‐thin thickness of the CNFs (micrometers long and 2–4 nm thick). These CNF networks expose high interfacial areas and can accommodate massive amounts of the ionic conductive liquid polyethylene glycol‐based electrolyte into strong homogeneous gel electrolytes. In addition to the reinforced mechanical properties, the presence of the CNFs simultaneously enhances the ionic conductivity due to their excellent strong water‐binding capacity according to computational simulations. This strategy renders the electrolyte a room‐temperature ionic conductivity of 0.61 ± 0.12 mS cm−1 which is one of the highest among polymer gel electrolytes. The electrolyte shows superior performances as a separator for lithium iron phosphate half‐cells in high specific capacity (161 mAh g−1 at 0.1C), excellent rate capability (5C), and cycling stability (94% capacity retention after 300 cycles at 1C) at 60 °C, as well as stable room temperature cycling performance and considerably improved safety compared with commercial liquid electrolyte systems.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Metal–Organic-Framework-Mediated Fast Self-Assembly 3D Interconnected Lignin-Based Cryogels in Deep Eutectic Solvent for Supercapacitor Applications

Rui Lou,Qihang Cao,Taoyuan Niu,Yiyi Zhang,Yanan Zhang,Zhiwei Wang,Xiao Zhang

DOI: https://doi.org/10.3390/polym15081824

IF: 5

2023-04-09

Polymers

Abstract:A cost-effective and sustainable method is successfully developed to produce lignin-based cryogels with a mechanically robust 3D interconnected structure. A choline chloride–lactic acid (ChCl–LA)-based deep eutectic solvent (DES) is used as a cosolvent to promote the synthesis of lignin–resorcinol–formaldehyde (LRF) gels that can self-assemble a robust string-bead-like framework. The molar ratio of LA to ChCl in DES has a significant influence on the gelation time and properties of the ensuing gels. Moreover, it is discovered that doping the metal–organic framework (MOF) during the sol–gel process can greatly accelerate the gelation of lignin. It takes a mere 4 h to complete the LRF gelation process at a DES ratio of 1:5 combined with 5% MOF. This study yields LRF carbon cryogels doped with copper that exhibit 3D interconnected bead-like carbon spheres with a prominent micropore of 1.2 nm. A specific capacitance as high as 185 F g−1 can be obtained for the LRF carbon electrode at a current density of 0.5 A g−1, and it has an excellent long-term cycling stability. This study provides a novel method of synthesizing high-lignin-content carbon cryogels with promising potential for application in the field of energy storage devices.

polymer science
Design of Fe3+-Rich, High-Conductivity Lignin Hydrogels for Supercapacitor and Sensor Applications.

Yonghao Ni,Qiuxia Zou,Dezhong Xu,A. Mondal,Shuai Wu,Fang Huang

DOI: https://doi.org/10.1021/acs.biomac.1c01194

2022-01-20

Biomacromolecules

Abstract:Preparation of natural polymer-based highly conductive hydrogels with tunable mechanical properties for applications in flexible electronics is still challenging. Herein, we report a facile method to prepare lignin-based Fe3+-rich, high-conductivity hydrogels via the following two-step process: (1) lignin hydrogels are prepared by cross-linking sulfonated lignin with poly(ethylene glycol) diglycidyl ether (PEGDGE) and (2) Fe3+ ions are impregnated into the lignin hydrogel by simply soaking in FeCl3. Benefiting from Fe3+ ion complexation with catechol groups and other functional groups in lignin, the resultant hydrogels exhibit unique properties, such as high conductivity (as high as 6.69 S·m-1) and excellent mechanical and hydrophobic properties. As a strain sensor, the as-prepared lignin hydrogel shows high sensitivity when detecting various human motions. With the flow of moist air, the Fe3+-rich lignin hydrogel generates an output voltage of 162.8 mV. The assembled supercapacitor of the hydrogel electrolyte demonstrates a high specific capacitance of 301.8 F·g-1, with a maximum energy density of 26.73 Wh·kg-1, a power density of 2.38 kW·kg-1, and a capacitance retention of 94.1% after 10 000 consecutive charge-discharge cycles. These results support the conclusion that lignin-based Fe3+-rich, high-conductivity hydrogels have promising applications in different fields, including sensors and supercapacitors, rendering a new platform for the value-added utilization of lignin.

Chemistry,Engineering,Medicine,Materials Science
Multifunction lignin-based carbon nanofibers with enhanced electromagnetic wave absorption and surpercapacitive energy storage capabilities

Boyu Du,Hongwei Zhu,Yating Bai,Jingyu Xu,Zheng Pan,Qingyu Wang,Xing Wang,Jinghui Zhou

DOI: https://doi.org/10.1016/j.ijbiomac.2021.12.154

IF: 8.2

2022-02-01

International Journal of Biological Macromolecules

Abstract:It is difficult for green sustainable lignin-based materials to simultaneously obtain efficient electromagnetic wave absorption (EMWA) and supercapacitive energy storage (SCES), which has not yet been reported. Herein, the light-weight lignin-based carbon nanofibers (LCNFs) with proper pore size, well graphitization degree, and heteroatom doping were tailored through electrospinning and carbonization processes. Interestingly, the graphitization degree and porous structure of LCNFs could be easily adjusted by changing the activating temperature, and the higher conductivity was achieved for preparing LCNFs at higher activating temperature due to the differences in the crystal size and activating degree of LCNFs. As a result, in the field of EMWA, the LCNFs-950 exhibited the minimum reflection loss (RL) value was -41.4 dB and the absorbing frequency was 9.05 GHz at 2.5 mm thickness, which meant this absorbent could absorb and/or dissipate more than 99.9% of incident electromagnetic wave (EMW). Furthermore, the LCNFs-950 also exhibited excellent SCES ability. In two-electrode system, the optimal LCNFs-950 symmetric supercapacitor specific capacitance reached 139.4 F/g at a current density of 0.5 A/g, meanwhile, the energy density was 41.4 Wh/kg at a power density of 3500 W/Kg. These multifunctional features of LCNFs will be highly promising for the next-generation environmental remediating materials.

polymer science,biochemistry & molecular biology,chemistry, applied
A high mechanical strength, deformable, fatigue-resistant polyacrylonitrile nanosphere-reinforced gel electrolyte for supercapacitors

Ning Liu,Weina Jia,Xia Li,Xuefeng Yan,Liangmin Yu

DOI: https://doi.org/10.1016/j.cej.2023.145701

IF: 15.1

2023-10-01

Chemical Engineering Journal

Abstract:There is an urgent need to develop gel electrolytes with excellent mechanical properties, deformability, and fatigue resistance to meet the flexibility requirements of novel supercapacitors. In this paper, polyacrylonitrile nanosphere-nanocomposite (PANNS-NC) hydrogels were synthesized by incorporating polyacrylonitrile nanospheres as reinforcing agents and employing N, N'-Methylenebis(acrylamide) (MBA) and N, N'-hexamethylenebisacrylamide (SMBA) as crosslinkers to achieve both physical and chemical crosslinking. The resulting PANNS-NC hydrogels demonstrated exceptional mechanical properties, including an ultrahigh elongation of 2380% and a remarkable tensile strength of 229.6 kPa. The gel electrolyte prepared from the PANNS-NC exhibited an ultrahigh ionic conductivity of 0.34 S·cm−1 and remarkable fatigue resistance, indicated by the absence of structural damage even after 1000 compression and tension cycles. Furthermore, the assembled supercapacitor demonstrated exceptional cycling stability, with a capacitance retention rate of 93% after 10,000 compression cycles with 50% strain. It maintained a 100% capacitance retention rate after 10,000 cycles with 90° bending. PANNS-NC holds great promise for use as a gel electrolyte material in supercapacitor development. Additionally, its suitability extends beyond supercapacitors, as it represents a novel material option for various other flexible devices.

engineering, chemical, environmental
High performance supercapacitors using lignin based electrospun carbon nanofiber electrodes in ionic liquid electrolytes

Rangana A Perera Jayawickramage,John P Ferraris

DOI: https://doi.org/10.1088/1361-6528/aafe95

IF: 3.5

2019-02-11

Nanotechnology

Abstract:Flexible, free standing and binder-free electrodes were fabricated by electrospinning from a series of lignin: polyvinyl alcohol (PVA) polymer blends, followed by heat treatment. PVA has the dual function of facilitating the electrospinning of lignin and acting as a sacrificial polymer. Upon stabilization, carbonization and CO2 activation, carbon nanofibers (ACNF) derived from the lignin:PVA 80:20 blend displayed a high surface area of 2170 m2 g-1 and a mesopore volume of 0.365 cm3 g-1. ACNFs derived from all the compositions show high degrees of graphitization based on Raman analysis. Pyr14TFSI ionic liquid (IL), modified by mixing with propylene carbonate and ethylene carbonate to reduce the viscosity and increase the ionic conductivity, was used as a high-performance electrolyte. The resulting IL mixture exhibited a four-fold increase in ionic conductivity compared to the neat IL Coin cell supercapacitors using electrodes derived from lignin:PVA 80:20 blends and this electrolyte displayed 87 F g-1 specific capacitance and 38 Wh kg-1 energy density which is the highest reported energy density for lignin:PVA blends to date.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
One-Pot Synthesis of a Double-Network Hydrogel Electrolyte with Extraordinarily Excellent Mechanical Properties for a Highly Compressible and Bendable Flexible Supercapacitor.

Mengni Shi,Tingrui Lin,Qingwen Bai,Furong Huang,Jiuqiang Li,Maolin Zhai,J. Peng

DOI: https://doi.org/10.1021/acsami.8b11377

2018-08-08

Abstract:High-performance hydrogel electrolytes play a crucial role in flexible supercapacitors (SCs). However, the unsatisfactory mechanical properties of widely used polyvinyl alcohol-based electrolytes greatly limit their use in the flexible SCs. Here, a novel Li2SO4-containing agarose/polyacrylamide double-network (Li-AG/PAM DN) hydrogel electrolyte was synthesized by a heating-cooling and subsequent radiation-induced polymerization and cross-linking process. The Li-AG/PAM DN hydrogel electrolyte possesses extremely excellent mechanical properties with a compression strength of 150 MPa, a fracture compression strain of above 99.9%, a tensile strength of 1103 kPa, and an elongation at break of 2780%, greatly superior to those have been reported. It also achieves a high ionic conductivity of 41 mS cm-1 originating from its interconnected three-dimensional porous network structure that provides a three-dimensional channel for ionic migration. Compared to the SC applying Li2SO4 aqueous solution electrolyte, the corresponding flexible Li-AG/PAM DN hydrogel electrolyte-SC presents lower charge-transfer resistance, better ionic diffusion, being closer to ideal capacitive behaviors, superior rate capability, and better cycling stability, owing to the improved ionic transport in the Li-AG/PAM DN hydrogel electrolyte and electrode interfaces. Moreover, after testing with overcharge, short circuit, and high temperature, the capacitance of the Li-AG/PAM DN hydrogel electrolyte-SC can still be well maintained. Furthermore, the electrochemical properties of the Li-AG/PAM DN hydrogel electrolyte-SC remain almost intact under different compression strains/bending angles and even after 1000 compression/bending cycles. It is expected that the Li-AG/PAM DN hydrogel electrolyte may have broad applications in modern flexible and wearable electronics.

Chemistry,Medicine,Engineering,Materials Science
Lignin-containing hydrogel matrices with enhanced adhesion and toughness for all-hydrogel supercapacitors

Dingkun Wang,Fusheng Yang,Lulu Cong,Wanglong Feng,Chunpeng Wang,Fuxiang Chu,Jingya Nan,Riqing Chen

DOI: https://doi.org/10.1016/j.cej.2022.138025

IF: 15.1

2022-07-15

Chemical Engineering Journal

Abstract:Flexible supercapacitors are promising energy storage devices benefitting from their portability and long cycle life. However, the weak interfacial adhesion between contiguous layers of flexible supercapacitors limits their practical applications. Here, a hydrogel matrix by integrating Ag-Lignin nanoparticles into polyacrylamide network is reported. Due to the unique interwoven-microfibrils structure and non-covalent interactions, the obtained hydrogel matrix presents largely enhanced adhesion and mechanical toughness. The assembled all-hydrogel supercapacitor based on the hydrogel matrix has robust interfaces and shows high specific capacitance (298.6 F g −1 at 10 mV s −1 ), outstanding rate performance, delivering high energy density of 13.7 Wh kg −1 and high capacitance retention of 89.9% after 10,000 cycles. Remarkably, the all-polymer device shows superior capacitance retention after mechanical deformations of 5000 cycles without slippage happens between contiguous layers. This study proposes an effective approach to improving the interfacial adhesion in integrated supercapacitors and extending the application scope of flexible supercapacitors.
Renewable symmetric supercapacitors assembled with lignin nanoparticles-based thin film electrolyte and carbon aerogel electrodes

Rui Lou,Taoyuan Niu,Fengyu Zhao,Long He,Yuejin Yuan,Guodong Wei,Gaojin Lyu

DOI: https://doi.org/10.1016/j.ijbiomac.2024.134474

Abstract:Lignin as a natural biopolymer is becoming increasingly in demand due to its eco-friendly properties, while lignin-based electrolyte with high conductivity and reliable durability for applications in supercapacitors is still challenging. Herein, a facile method to prepare lignin nanoparticles (LNPs)-based solid electrolyte thin film (LF) was proposed through chemical cross-linking reaction. The fabricated LF exhibited a distinctive spongy porous structure with the ionic conductivity of 3.26 mS cm-1, demonstrating the exceptional flexibility and favorable mechanical properties. Moreover, the assembly of all-LNPs-based symmetric supercapacitor (SSC) devices was achieved using LF electrolyte and LCA electrodes for the first time, confirming the LF3 electrolyte superior to commercial cellulose separator in capacitive behaviour. This SSC device exhibited a specific capacitance of 122.7 F g-1 at 0.5 A g-1 and the maximum energy density of 17.04 W h kg-1. Furthermore, the incorporation of sodium alginate (SA) significantly enhanced the ionic conductivity of SA/LF3 electrolyte, and the resulting SSC device delivered a higher specific capacitance of 174.5 F g-1 at 0.5 A g-1 and the maximum energy and power densities of 24.24 W h kg-1 and 5023 W kg-1, respectively. This study proposes a promising approach for sustainable utilization of lignin in energy storage applications.
Preparation of lignosulfonate ionic hydrogels for supercapacitors, sensors and dye adsorbent applications

Ajoy Kanti Mondal,Shuai Wu,Dezhong Xu,Qiuxia Zou,Lihui Chen,Liulian Huang,Fang Huang,Yonghao Ni

DOI: https://doi.org/10.1016/j.ijbiomac.2021.07.021

2021-09-30

Abstract:Lignin, an abundant natural polymer but presently under-utilized, has received much attention for its green/sustainable advantages. Herein, we report a facile method to fabricate lignosulfonate (LS) ionic hydrogels by simple crosslinking with poly (ethylene glycol) diglycidyl ether (PEGDGE). The as-obtained LS-PEGDGE hydrogels were comprehensively characterized by mechanical measurements, FT-IR, and SEM. The rich sulfonic and phenolic hydroxyl groups in LS hydrogels play key roles in imparting multifunctional smart properties, such as adhesiveness, conducting, sensing and dye adsorption, as well as superconductive behavior when increasing the moisture content. The hydrogels have a high adsorption capacity for cationic dyes, using methylene blue as a model, reaching 211 mg·g-1. As a moist-induced power generator, the maximum output voltage is 181 mV. The LS-PEGDGE hydrogel-based flexible strain sensors exhibit high sensitivity when detecting human movements. As the hydrogel electrolyte, the assembled supercapacitor shows high specific capacitance of 236.9 F·g-1, with the maximum energy density of 20.61 Wh·kg-1, power density of 2306.4 W·kg-1, and capacitance retention of 92.9% after 10,000 consecutive charge-discharge cycles. Therefore, this multifunctional LS hydrogels may have promising applications in various fields, providing a new platform for the value-added utilization of lignin from industrial waste.
Cellulose-based high-loading flexible electrode for lithium-ion battery with high volumetric energy density

Zhenyu Jiang,Chuanqi Huang,Sijia Zhang,Wenbin Luo,Yi Cheng,Xiaofei Yang

DOI: https://doi.org/10.1016/j.cej.2024.151189

IF: 15.1

2024-04-16

Chemical Engineering Journal

Abstract:Thick electrodes with high loading are attractive for high-energy storage devices, but they face major challenges of slow ion transfer and poor mechanical stability. Carbon templates such as reduced graphene oxide and carbon nanotube can promote the electrons transfer of thick electrodes and enhance their strength, but they still exhibit a complex producing process, slow Li + transfer and high cost. Herein, a nanofiber network with double fast Li + and electrons transfer pathways by the self-assembly of carbon nanoparticles on the negatively charged natural cellulose fibers was designed. The abundant oxygen-containing functional groups from the cellulose fibers enabled the electrode with abundant negative charge which can adsorb the neutral particles with strong electrostatic interaction. And the Density Functional Theory calculation demonstrates that oxygen-containing functional groups also has stronger adsorption energy for PF 6 − anions in electrolyte which can promote the desolvation of the solvated Li salts, thus promote Li + transfer. After integration with lithium iron phosphate, this network achieves a robust high-loaded electrode with good electrical conductivity and shortened ion transfer pathways without traditional current collector and binder. Based on the robust electrode structure and fast transfer kinetics of electrons and Li + , the batteries exhibit excellent cycle stability with capacity retention of 98 % after long 400 cycles and high volumetric energy density of 740 Wh/L, which greatly surpass the conventional batteries with coating LiFePO 4 (LFP) cathode. Given the low-cost raw materials and convenient operation, the design of self-standing flexible electrodes with high loading will offer a promising and effective strategy for other storage devices with high energy.

engineering, chemical, environmental
Highly Stretchable, Self-Recoverable, and Conductive Double-Network Gels Containing Deep Eutectic Solvent for a Flexible Supercapacitor and Strain Sensor

Linlin Wu,Jiacheng Zhou,Ximan Bu,Yongxin Ge,Yifeng Gao,Xiaofeng Ma

DOI: https://doi.org/10.1007/s11664-022-09743-z

IF: 2.1

2022-06-22

Journal of Electronic Materials

Abstract:Due to the advantages of high ion density, low volatility, non-toxicity, and low cost, deep eutectic solvent gels have attracted widespread interest as novel solid-state ionic conductors for flexible devices. However, most of the currently developed deep eutectic solvent gels have weak mechanical properties, which seriously hinder their large-scale application. Herein, tough and ultrastretchable agar-based double-network deep eutectic solvent gels were successfully fabricated through the self-assembly of agar at a concentration range of 2% to 6% in a choline chloride/urea/water eutectic mixture (ChCl:urea:H2O = 1:2:1) by heating–cooling to form the first physical dissipative network and combination with the second Al3+-cross-linked hybrid poly(acrylic acid) (PAA) network. Such a double-network and multi-bond design endow the obtained 22 wt.% polymer scaffold-supported deep eutectic solvent gels with good mechanical properties (high tensile strength of 216 kPa and toughness of 2112 kJ m−3), stretchability (breaking strain of 1566%), good self-recovery ability (91% recovery efficiency after 600% strain deformation), and high room-temperature ionic conductivity of 2.1 mS cm−1. Furthermore, agar-based double network deep eutectic solvent gels were successfully used as stretchable gel electrolytes for the fabrication of electric double-layer capacitors and reliable flexible sensors with excellent electrochemical performance over a wide strain range.Graphical AbstractA nonvolatile agar-based double-network gel containing a deep eutectic solvent with high toughness of 2112 kJ m−3, high stretchability of 1595%, excellent recovery property, and ionic conductivity of 2.1 mS cm−1 is fabricated for flexible electronics by the self-assembly of agar in a choline chloride/urea/water eutectic mixture (ChCl:urea:H2O = 1:2:1) to form the first physical dissipative network and combination with a second Al3+-cross-linked hybrid PAA network.

engineering, electrical & electronic,materials science, multidisciplinary,physics, applied
Polymerized lignin based carbon nanofiber for high-performance energy generator and storage

Chuangqi Zheng,Qiping Cao,Lei Pu,Jingyu Xu,Hui Gong,Ziyi Shen,Kaibin Chu,Dechao Chen,Qin Li,Ning Han,Yao Li

DOI: https://doi.org/10.1016/j.cej.2024.156342

IF: 15.1

2024-10-13

Chemical Engineering Journal

Abstract:Lignin is an ideal precursor for the preparation of lignin-based materials. However, the lack of molecular weight, thermal stability and spatial configuration of lignin hinder the practical application of lignin in lignin-based carbon materials. Herein, a novel and effective strategy for preparing high-performance lignin-based carbon nanofibers (CFs) is designed. Lignin samples with different chemical structures are prepared by polymerization modification and fractionation. This strategy completely gets rid of the dependence on petroleum-based polymers in the electrospinning process, and makes the lignin-based CFs show good performance in energy storage, temperature sensor, and moisture power generation. The specific capacitance and energy of lignin-based supercapacitors reach 357.2 F/g and 31.5 Wh/kg, respectively. The CFs exhibit good flame retardancy and thermal sensitivity, and the response time is 1 s. In addition, moisture power generators assembled with CFs exhibit great potential. The output voltage of moisture power generators has a linear relationship with the number of devices. With the increase of series equipment, the output voltage of 5 series moisture power generators is 4.7 V. This work provides a new approach to prepare high-performance lignin-based carbon nanofibers, which has a good application prospect in the fields of energy storage, sensing and power generation.

engineering, chemical, environmental
Deep eutectic solvent-based eutectogels consisting of ZnCl2 and lignin for quasi-solid-state supercapacitors

Yunhua Bai,Xiong-Fei Zhang,Yufang Wu,Hu Liu,Jianfeng Yao

DOI: https://doi.org/10.1039/d4ta04960h

IF: 11.9

2024-09-27

Journal of Materials Chemistry A

Abstract:Eutectogels have attracted attention for use in flexible electronics and energy storage because of their high conductivity and good mechanical properties. In this work, using ZnCl 2 as a hydrogen bond acceptor and lactic acid (LA) as a hydrogen bond donor, an inorganic salt-based deep eutectic solvent (DES) was designed. The DES was used to extract lignin from poplar sawdust, and then poly(vinyl alcohol) was added to the mixed DES/lignin solution to obtain the eutectogels. Due to extensive hydrogen bonding and Zn 2+ -induced coordination, the eutectogels present high ionic conductivity, good stretchability, and wide temperature tolerance. In particular, the presence of lignin endows the eutectogels with self-adhesive properties and enhanced mechanical strength. By regulating the lignin content, the optimal eutectogel sample exhibited an ionic conductivity of 23.8 mS cm −1 , tensile strength of 331 kPa, and elongation at break of 1000%, and it could be stable for a long time at −20 °C. Furthermore, the eutectogel quasi-solid-state electrolyte in a zinc-ion hybrid supercapacitor has a high capacity of 251 mA h g −1 at 0.5 A g −1 , and it provides stable adhesion and mechanical strength at low temperatures. After 10 000 charge/discharge cycles, these capacitors demonstrated over 86% capacitance retention and 100% coulombic efficiency.

materials science, multidisciplinary,chemistry, physical,energy & fuels
A Flexible Supercapacitor with High Energy Density Driven by MXene/Deep Eutectic Solvent Gel Polyelectrolyte

Jinxu Huang,Yuanyuan Hu,Jianzhu Li,Hao Wang,Tiansheng Wang,Hao Wu,Yujie Li,Mi Wang,Jiaheng Zhang

DOI: https://doi.org/10.1021/acsenergylett.3c00340

IF: 22

2023-04-20

ACS Energy Letters

Abstract:Limited by low operating voltages and insufficient understanding of the electrolyte component interaction mechanisms, electrochemical double-layer capacitors (EDLCs) exhibit unsatisfactory energy density and significant energy loss under low temperatures. Herein, we propose a new strategy for the synthesis of a green gel polymer electrolyte employing polyacrylamide (PAM) as a cross-linking network based on a Li-salt containing a deep eutectic solvent (DES). Remarkably, the addition of lignin and MXene contribute significantly to boost the performance of the device with DES gel polyelectrolyte, mainly through the Lewis acid–base interactions between the abundant functional groups (−F and −OH) and TFSI– group. We have also confirmed the occurrence of this interaction and the mechanism of improving conductivity and operating voltage by molecular dynamics simulations. Consequently, the device delivers a wide potential window of 0–2.4 V and the highest weight energy density of 42.6 Wh kg–1. This work offers new insight into the fabrication of green and flexible devices with high energy density without producing electronic waste.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,energy & fuels,electrochemistry
When the End (Automatically) Justifies the Means: Automatic Tendency Toward Sex Exchange for Crack Cocaine.

Catalina E Kopetz,Anahi Collado,C. Lejuez

DOI: https://doi.org/10.1037/MOT0000025

2015-12-01

Motivation Science

Abstract:The current research explores the idea that self-defeating behaviors represent means toward individuals' goals. In this quality, they may be automatically initiated upon goal activation without individual's voluntary intention and thus exemplify the long-held idea that the end justifies the means. To investigate this notion empirically we explored one of the most problematic self-defeating behavior: engagement in sex exchange for crack cocaine. This behavior is common among female drug users despite its well-known health and legal consequences. Although these women know and understand the consequences of such behavior, they have a hard time resisting it when the goal of drug obtainment becomes accessible. Indeed, the current study shows that when the accessibility of such a goal is experimentally increased, participants for whom sex exchange represents an instrumental means to drug obtainment are faster to approach sex-exchange targets in a joystick task despite their self-reported intentions to avoid such behavior.
High Performance Electrospun Li+-functionalized Sulfonated Poly(ether Ether Ketone)/pva Based Nanocomposite Gel Polymer Electrolyte for Solid-State Electric Double Layer Capacitors.

Nan Lu,Xi Zhang,Ruiqi Na,Wendi Ma,Chongyang Zhang,Yuchao Luo,Yongfeng Mu,Shuling Zhang,Guibin Wang

DOI: https://doi.org/10.1016/j.jcis.2018.09.027

IF: 9.9

2019-01-01

Journal of Colloid and Interface Science

Abstract:The synthesis of a nanocomposite gel polymer electrolytes (NGPEs) using Li+-nctionalized SPEEK (SPEEK(Li)) nanofiber membrane as a matrix, cross-linked PVA as a gelled agent and LiCIO4 as an electrolytic salt for electric double layer capacitors (EDLCs) were reported in this work. Compared with conventional PVA based gel electrolyte, the "SO3-Li" functional groups and the pores structure of the SPEEK (Li) nanofiber membrane improves the ionic conductivity as well as mechanical stability, which made the prepared NGPEs exhibited a high ionic conductivity of 8.9 x 10(-3) S cm(-1) at ambient temperature and a large voltage stability window range from 0 to 2.0 V. The fabricated symmetric EDLCs showed a specific capacitance of 146.96 F g(-1) at a current density of 0.5 A g(-1), with a maximum energy density of 18.26 W h kg(-1). Meanwhile, the EDLCs showed outstanding cyclical stability of 98% specific capacitance retention after 3000 cycles GCD testing, all of these results indicated that the NGPEs should be appropriate to EDLCs and next-generation energy storage systems. (C) 2018 Elsevier Inc. All rights reserved.
ON THE POSSIBILITY OF LYSOPHOSPHATIDE FORMATION DURING WALLERIAN DEGENERATION

J. Domonkos,L. Heiner

DOI: https://doi.org/10.1111/j.1471-4159.1968.tb06179.x

1968-02-01

Journal of Neurochemistry

Abstract:—During an extensive decomposition of phospholipids, at the end of the second week of Wallerian degeneration, the decomposition of glycerophosphatides were studied in detail. In a degenerative process lasting for 2 weeks about one‐third of the choline phosphatides, two‐thirds of the ethanolamine phosphatides, one‐third of the serine phosphatides and one‐quarter of the inositol phosphatides, were destroyed.

Die Continuität des Lebens als Grundlage der modernen biologischen Anschauung

Lignin-induced rapid-synthesis of deep eutectic solvent-based gel with high robustness and conductivity applied for flexible quasi-solid-state supercapacitors

Enhancement of charge transport in interconnected lignin-derived carbon fibrous network for flexible battery-supercapacitor hybrid device

Dynamic Networks of Cellulose Nanofibrils Enable Highly Conductive and Strong Polymer Gel Electrolytes for Lithium‐Ion Batteries

Metal–Organic-Framework-Mediated Fast Self-Assembly 3D Interconnected Lignin-Based Cryogels in Deep Eutectic Solvent for Supercapacitor Applications

Design of Fe3+-Rich, High-Conductivity Lignin Hydrogels for Supercapacitor and Sensor Applications.

Multifunction lignin-based carbon nanofibers with enhanced electromagnetic wave absorption and surpercapacitive energy storage capabilities

A high mechanical strength, deformable, fatigue-resistant polyacrylonitrile nanosphere-reinforced gel electrolyte for supercapacitors

High performance supercapacitors using lignin based electrospun carbon nanofiber electrodes in ionic liquid electrolytes

One-Pot Synthesis of a Double-Network Hydrogel Electrolyte with Extraordinarily Excellent Mechanical Properties for a Highly Compressible and Bendable Flexible Supercapacitor.

Lignin-containing hydrogel matrices with enhanced adhesion and toughness for all-hydrogel supercapacitors

Renewable symmetric supercapacitors assembled with lignin nanoparticles-based thin film electrolyte and carbon aerogel electrodes

Preparation of lignosulfonate ionic hydrogels for supercapacitors, sensors and dye adsorbent applications

Cellulose-based high-loading flexible electrode for lithium-ion battery with high volumetric energy density

Highly Stretchable, Self-Recoverable, and Conductive Double-Network Gels Containing Deep Eutectic Solvent for a Flexible Supercapacitor and Strain Sensor

Polymerized lignin based carbon nanofiber for high-performance energy generator and storage

Deep eutectic solvent-based eutectogels consisting of ZnCl2 and lignin for quasi-solid-state supercapacitors

A Flexible Supercapacitor with High Energy Density Driven by MXene/Deep Eutectic Solvent Gel Polyelectrolyte

When the End (Automatically) Justifies the Means: Automatic Tendency Toward Sex Exchange for Crack Cocaine.

High Performance Electrospun Li+-functionalized Sulfonated Poly(ether Ether Ketone)/pva Based Nanocomposite Gel Polymer Electrolyte for Solid-State Electric Double Layer Capacitors.

ON THE POSSIBILITY OF LYSOPHOSPHATIDE FORMATION DURING WALLERIAN DEGENERATION