A loss-of-function mutation in the CFC domain of TDGF1 is associated with human forebrain defects

June de la Cruz,R. Bamford,R. Burdine,E. Roessler,J. Barkovich,D. Donnai,A. Schier,M. Muenke

DOI: https://doi.org/10.1007/s00439-002-0709-3

2002-04-10

Human Genetics

Abstract:

What problem does this paper attempt to address?

Minimal-Invasive Levodopa Sensing Based on Differential Amperometry Microneedle Electrodes Decorated with Spike-like Au Nanoparticles

Hangxu Ren,Xiyu Mao,Shanshan Zhang,Yu Cai,Shiyi Xu,Lu Fang,Xuesong Ye,Bo Liang

DOI: https://doi.org/10.1109/NEMS51815.2021.9451475

2021-01-01

Abstract:Levodopa is the most commonly used drug for Parkinson's disease treatment since its inception. The concentration of levodopa must stay in a narrow range to achieve a better curative result which relies on the optimization of dosage. To adjust the dosage objectively and timely, it is of great significance to monitor the dynamic concentration of levodopa in Parkinson's patients. However, the high co...
Differential Amperometric Microneedle Biosensor for Wearable Levodopa Monitoring of Parkinson's Disease

Lu Fang,Hangxu Ren,Xiyu Mao,Shanshan Zhang,Yu Cai,Shiyi Xu,Yi Zhang,Lihua Li,Xuesong Ye,Bo Liang

DOI: https://doi.org/10.3390/bios12020102

2022-01-01

Abstract:Levodopa (L-Dopa) is considered to be one of the most effective therapies available for Parkinson’s disease (PD) treatment. The therapeutic window of L-Dopa is narrow due to its short half-life, and long-time L-Dopa treatment will cause some side effects such as dyskinesias, psychosis, and orthostatic hypotension. Therefore, it is of great significance to monitor the dynamic concentration of L-Dopa for PD patients with wearable biosensors to reduce the risk of complications. However, the high concentration of interferents in the body brings great challenges to the in vivo monitoring of L-Dopa. To address this issue, we proposed a minimal-invasive L-Dopa biosensor based on a flexible differential microneedle array (FDMA). One working electrode responded to L-Dopa and interfering substances, while the other working electrode only responded to electroactive interferences. The differential current response of these two electrodes was related to the concentration of L-Dopa by eliminating the common mode interference. The differential structure provided the sensor with excellent anti-interference performance and improved the sensor’s accuracy. This novel flexible microneedle sensor exhibited favorable analytical performance of a wide linear dynamic range (0–20 μM), high sensitivity (12.618 nA μM−1 cm−2) as well as long-term stability (two weeks). Ultimately, the L-Dopa sensor displayed a fast response to in vivo L-Dopa dynamically with considerable anti-interference ability. All these attractive performances indicated the feasibility of this FDMA for minimal invasive and continuous monitoring of L-Dopa dynamic concentration for Parkinson’s disease.
Differential Coulometry Based on Dual Screen-Printed Strips for High Accuracy Levodopa Determination Towards Parkinson's Disease Management

Congcong Yu,Qingpeng Cao,Tingting Tu,Yu Cai,Lu Fang,Xuesong Ye,Bo Liang

DOI: https://doi.org/10.1016/j.jpba.2020.113498

IF: 3.571

2020-01-01

Journal of Pharmaceutical and Biomedical Analysis

Abstract:As a vital therapeutic agent for Parkinson's disease, dosage control of levodopa has always been a major obstacle in ensuring efficacy and curbing side effects. Simple and fast electrochemical detection methods are the main force in this field. Here, we presented a differential dual-strip method based on the coulometry for high accuracy determination of levodopa. The difference between the two strip signals with or without the tyrosinase extracted the levodopa signal from the samples. The Prussian Blue modified carbon screen-printed electrode was used to convert and amplify the electrochemical signal upon the presence of levodopa. The system exhibited a linear behavior in the 0–10 μM concentration range and a detection limit of 0.25 μM. Furthermore, it was proved to be stable in effectively distinguishing levodopa from complex samples through anti-interference experiments and serum tests. We demonstrated the superiority of dual-strip differential coulometry for the determination of levodopa towards Parkinson’s disease clinical management.
Electrochemical Determination of Dopamine Using a Carboxyl-functionalized Carbon Nanotube-Modified Carbon Paste Electrode Doped with Polymeric Ferric Sulfate

Ting Ni,Tengfei Wang,Lingling Xi

DOI: https://doi.org/10.1080/00032719.2016.1245316

2017-01-01

Analytical Letters

Abstract:A novel electrochemical device for the sensitive determination of dopamine was developed based on a carbon paste electrode with polymeric ferric sulfate doped in the carbon paste and a carboxyl-functionalized carbon nanotube thin film on the surface. The modified electrode was characterized by scanning electron microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. The conditions for the preparation of electrode were optimized. The carbon nanotubes were shown to be stable on the surface of carbon paste electrode. The novel electrochemical device provided excellent activity toward dopamine. Amperometry and differential pulse voltammetry were used for the determination of dopamine in pH 7.0 phosphate buffer with a long linear range from 0.8 to 261 mu M and a detection limit of 0.2 mu M. The modified electrode showed excellent repeatability, good stability, and satisfactory reproducibility, thus demonstrating potential for practical applications.
Study on Levodopa Sensor Modified by Ti3C2 MXene

Yi Zhang,Xiaoyu Xia,Jialong Shou,Bo Liang,Lu Fang

DOI: https://doi.org/10.1088/1742-6596/2500/1/012004

2023-01-01

Abstract:The dosage management of levodopa is of great significance in the treatment of Parkinson's disease. Measuring the patient's levodopa concentration helps the physician to adjust the dose in time, so as to avoid complications. In this paper, we report an electrochemical sensor based on titanium carbide (Ti3C2) MXene nanomaterials, which can sensitively reflect the change of levodopa concentration. In the study, Ti3C2/GCE electrode was prepared by a simple drop-coating method, and then the Ti3C2/Pt/GCE electrode was prepared by modifying Pt nanoparticles on the electrode surface by impregnation adsorption method. After modification, the response of the GCE electrode to levodopa before and after Ti3C2 decoration was compared by cyclic voltammetry (CV), and the diffusion control process on the electrode surface was also investigated. Then, differential pulse voltammetry (DPV) was used to explore the relationship between the peak current of the oxidation anode and the concentration of levodopa. Finally, the relationship between current and concentration at a certain time point was explored by chronoamperometry (CA), and the time charge curves were plotted to explore the functional relationship between the amount of charge exchanged in the reaction and the concentration of levodopa (Coulomb analysis method). The research shows that the coulomb analysis method has a higher detection sensitivity and linear range, and this technology is expected to be applied to the in vivo monitoring of levodopa in our future research.
Eu2O3@Cr2O3 Nanoparticles-Modified Carbon Paste Electrode for Efficient Electrochemical Sensing of Neurotransmitters Precursor L-DOPA

Aleksandar Mijajlović,Miloš Ognjanović,Dragan Manojlović,Filip Vlahović,Slađana Đurđić,Vesna Stanković,Dalibor Stanković

DOI: https://doi.org/10.3390/bios13020201

2023-01-29

Biosensors

Abstract:There are ten million people in the world who have Parkinson's disease. The most potent medicine for Parkinson's disease is levodopa (L-DOPA). However, long-term consumption of L-DOPA leads to the appearance of side effects, as a result of which the control and monitoring of its concentrations are of great importance. In this work, we have designed a new electrochemical sensor for detecting L-DOPA using a carbon paste electrode (CPE) modified with Eu2O3@Cr2O3 composite nanoparticles. Rare earth elements, including Eu, are increasingly used to design new electrode nanocomposites with enhanced electrocatalytic properties. Europium has been considered a significant lanthanide element with greater redox reaction behavior. We conducted a hydrothermal synthesis of Eu2O3@Cr2O3 and, for the first time, the acquired nanoparticles were used to modify CPE. The proposed Eu2O3@Cr2O3/CPE electrode was investigated in terms of its electrocatalytic properties and then used to develop an analytical method for detecting and quantifying L-DOPA. The proposed sensor offers a wide linear range (1–100 μM), high sensitivity (1.38 μA μM−1 cm−2) and a low detection limit (0.72 μM). The practical application of the proposed sensor was investigated by analyzing commercially available pharmaceutical tablets of L-DOPA. The corresponding results indicate the excellent potential of the Eu2O3@Cr2O3/CPE sensor for application in real-time L-DOPA detection.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation
Smartphone-based differential pulse amperometry system for real-time monitoring of levodopa with carbon nanotubes and gold nanoparticles modified screen-printing electrodes

Daizong Ji,Ning Xu,Zixiang Liu,Zhouyuanjing Shi,Sze Shin Low,Jingjing Liu,Chen Cheng,Jingwen Zhu,Tingkai Zhang,Haoxuan Xu,Xiongjie Yu,Qingjun Liu

DOI: https://doi.org/10.1016/j.bios.2018.09.082

2019-03-15

Abstract:Parkinson's disease caused by lack of dopamine in brain is a common neurodegenerative disorder. The traditional treatment is to replenish levodopa since it could pass through blood brain barrier and form dopamine. However, its accumulation can cause patients' movement disorders and uncontrollable emotion. Therefore, it is critical to control the levodopa dosage accuracy to improve the curative effect in clinical. In this study, a smartphone-based electrochemical detection system was developed for rapid monitoring of levodopa. The system involved a disposable sensor, a hand-held electrochemical detector, and a smartphone with designed application. Single-wall carbon nanotubes and gold nanoparticles modified screen-printed electrodes were used to convert and amplify the electrochemical current signals upon presence of levodopa molecules. The electrochemical detectors were used to generate electrochemical excitation signals and detect the resultant currents. Smartphone was connected to the detector, which was used to control the detector, calculate data, and plot graph in real-time. The smartphone-based differential pulse amperometry system was demonstrated to monitor levodopa at concentrations as low as 0.5 µM in human serum. Furthermore, it has also been verified to be able to distinguish levodopa from other representative substances in the body. Therefore, its performance was more sensitive and rapid than electrochemical workstation. With these advantages, the system can be used in the field of point-of-care testing (POCT) to detect levodopa and provide the possibility to solve clinical demand for levodopa detection.
A Sensitive Photoelectrochemical Sensor for Levodopa Detection Using Benzothiadiazole-Based Conjugated Microporous Polymer-Coated Graphene Heterostructures

Gang Xiang,Xiansen He,Yuxia Liu,Qing Huang,Wei Huang,Cuizhong Zhang,Jinyun Peng

DOI: https://doi.org/10.1021/acsami.2c15516

2022-11-04

Abstract:Since the 1960s, levodopa (LDA) has been the standard drug for treating of Parkinson's disease. In this study, a novel benzothiadiazole-based conjugated microporous polymer-coated graphene heterostructure (CMP-rGO) was synthesized and used to construct a sensitive photoelectrochemical (PEC) sensor capable of detecting LDA. Under optimal experimental conditions, the intensity of the photocurrent produced by the sensor was linear from 0.005 to 40 μM, and the limit of detection of the sensor was...

materials science, multidisciplinary,nanoscience & nanotechnology
[The clinical effect of intravenous regional sympathectomy with guanethidine in the management of sympathetically maintained pain].

M. Onaka,M. Morimoto,E. Morimoto,M. Kurioka,H. Otada,M. Hyodo

1992-09-01

Abstract:We treated 25 patients suffering from sympathetically maintained pain with intravenous regional sympathectomy with guanethidine. Of these patients, 18 had reflex sympathetic dystrophy; 5 had causalgia; and 2 had shoulder hand syndrome. The visual analog scale before IRS therapy was 6.1 +/- 0.3, and after therapy, it was 2.3 +/- 0.4. The mean rate of improvement was 54.2% in reflex sympathetic dystrophy and 81.0% in causalgia. The therapy was particularly effective in patients with shoulder hand syndrome. These results suggest that intravenous regional sympathectomy with guanethidine could be effective for sympathetically maintained pain.
In-situ anchoring bimetallic nanoparticles on covalent organic framework as an ultrasensitive electrochemical sensor for levodopa detection

Xin Sun,Na Wang,Yao Xie,Huacong Chu,Yang Wang,Yi Wang

DOI: https://doi.org/10.1016/j.talanta.2020.122072

IF: 6.1

2021-04-01

Talanta

Abstract:Covalent organic frameworks (COFs) have been studied in many fields. However, their electrochemical properties were seldom reported. In this work, a novel high electrocatalytic material was synthesized by incorporating bimetallic nanoparticles (AgCoNPs) in a two-dimensional (2D) porous TAPB-DMTP-COF, (AgCo/TAPB-DMTP-COF, TAPB, 1,3,5-tris(4-aminophenyl)benzene; DMTP, 2,5-dimethoxyterephaldehyde). Subsequently, the resulting composite was further used to construct a novel electrochemical sensor for the ultrasensitive determination of levodopa. The analytical performance has been improved significantly due to the synergistic effect of both TAPB-DMTP-COF and AgCoNPs by increasing effective electroactive surface area and electron transfer efficiency. The linear detection range of the levodopa sensor was 0.010–100 μmol L−1. The limits of detection and quantitation were found to be 0.002 and 0.006 μmol L−1, respectively. Moreover, the sensor exhibits an excellent stability and maintains its catalytic activity after 100 scanning rounds. The applicability of the electrochemical sensor was successfully applied for the determination of levodopa content in human urine and blood serum samples. Our study not only supplies a useful tool to accurately detect levodopa in actual samples and, meanwhile, but paves a feasible way to unlock high performance 2D COF based electrode materials.

chemistry, analytical
Electrochemical determination of levodopa using ZnO nanowire arrays/graphene foam

LIN Xuan-yu,ZHANG Hong,HUANG Shuo,CHANG Jing,GAO Xin,YAO Long-hui,YUE Hong-yan

DOI: https://doi.org/10.13374/j.issn2095-9389.2016.09.016

2016-01-01

Abstract:A three-dimensional (3D), macroporous and highly conductive grapheme foam (GF) was synthesized by chemical vapor deposition using a nickel foam as a template. ZnO nanowire arrays were vertically grown on the surface of the prepared GF using hydrothermal synthesis. The morphologies and structure of the ZnO NWAs/GF were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction and Raman spectroscopy. The results show that the prepared GF is high-quality and defect free, and the ZnO NWAs with uniform size vertically grows on the surface of 3D GF. The ZnO NWAs/GF was used as an elec-trochemical electrode for determining levodopa ( LD) . The results of electrochemical tests show that the oxidation current of LD is well linear with its concentration in the range of 0-80μmol·L-1 with a sensitivity of 0. 41μA·(μmol·L-1 ) -1 , and the ZnO NWAs/GF electrode also shows good reproducibility and stability. The ZnO NWAs/GF can detect LD with high selectivity in the presence of uric acid.
Biosensor Strip for Rapid On‐site Assessment of Levodopa Pharmacokinetics along with Motor Performance in Parkinson's Disease

Kuldeep Mahato,Jong-Min Moon,Chochanon Moonla,Katherine Longardner,Hamidreza Ghodsi,Irene Litvan,Joseph Wang

DOI: https://doi.org/10.1002/anie.202403583

2024-04-30

Angewandte Chemie International Edition

Abstract:While levodopa (L-Dopa) is the primary treatment for alleviating Parkinson's disease (PD), its efficacy is hindered by challenges such as a short half-life and inconsistent plasma levels. As PD progresses, the rising need for increased and more frequent L-Dopa doses coupled with symptom fluctuations and dyskinesias underscores the urgency for improved comprehension of the interplay between L-Dopa levels and PD motor symptoms. Addressing this critical need, we present a decentralized testing method using a disposable biosensor strip and a universal slope (U-slope) calibration-free approach. This enables reliable, rapid, simple, and cost-effective decentralized L-Dopa measurements from capillary blood. A pilot study with PD persons demonstrates the ability to monitor real-time L-Dopa pharmacokinetics from fingerstick blood after oral L-Dopa-Carbidopa (C-Dopa) tablet administration. Correlating capillary blood L-Dopa levels with PD motor scores revealed a well-defined inverse correlation with temporal motor fluctuations. We compared the resulting dynamic capillary blood L-Dopa levels with plasma L-Dopa levels using the traditional but clinically impractical high-performance liquid chromatography technique. By providing timely feedback on a proper L-Dopa dosing regimen in a decentralized and rapid fashion, this new biosensing platform will facilitate tailored optimal L-Dopa dosing, towards improving symptom management and enhancing health-related quality of life.

chemistry, multidisciplinary
A Critical Overview of Enzyme-Based Electrochemical Biosensors for L-Dopa Detection in Biological Samples

Carmen Tesoro,Giuseppa Cembalo,Antonio Guerrieri,Giuliana Bianco,Maria Assunta Acquavia,Angela Di Capua,Filomena Lelario,Rosanna Ciriello

DOI: https://doi.org/10.3390/chemosensors11100523

2023-10-05

Chemosensors

Abstract:L-Dopa is an intermediate amino acid in the biosynthesis of endogenous catecholamines, such as dopamine. It is currently considered to be the optimal dopaminergic treatment for Parkinson’s disease, a neurodegenerative disorder affecting around 1% of the population. In an advanced stage of the disease, complications such as dyskinesia and psychosis are caused by fluctuations in plasma drug levels. Real-time monitoring of L-Dopa levels would be advantageous for properly adjusting drug dosing, thus improving therapeutic efficacy. Electrochemical methods have advantages such as easy-to-use instrumentation, fast response time, and high sensitivity, and are suitable for miniaturization, enabling the fabrication of implantable or wearable devices. This review reports on research papers of the past 20 years (2003–2023) dealing with enzyme-based biosensors for the electrochemical detection of L-Dopa in biological samples. Specifically, amperometric and voltammetric biosensors, whose output signal is a measurable current, are discussed. The approach adopted includes an initial study of the steps required to assemble the devices, i.e., electrode modification and enzyme immobilization. Then, all issues related to their analytical performance in terms of sensitivity, selectivity, and capability to analyze real samples are critically discussed. The paper aims to provide an assessment of recent developments while highlighting limitations such as poor selectivity and long-term stability, and the laborious and time-consuming fabrication protocol that needs to be addressed from the perspective of the integrated clinical management of Parkinson’s disease.

chemistry, analytical,electrochemistry,instruments & instrumentation
Electrochemical Detection of Dopamine at Fe3O4/SPEEK Modified Electrode

Mogomotsi N. Ranku,Gloria E. Uwaya,Omolola E. Fayemi

DOI: https://doi.org/10.3390/molecules26175357

IF: 4.6

2021-09-03

Molecules

Abstract:Reported here is the design of an electrochemical sensor for dopamine (DA) based on a screen print carbon electrode modified with a sulphonated polyether ether ketone-iron (III) oxide composite (SPCE-Fe3O4/SPEEK). L. serica leaf extract was used in the synthesis of iron (III) oxide nanoparticles (Fe3O4NPs). Successful synthesis of Fe3O4NP was confirmed through characterization using Fourier transform infrared (FTIR), ultraviolet–visible light (UV–VIS), X-ray diffractometer (XRD), and scanning electron microscopy (SEM). Cyclic voltammetry (CV) was used to investigate the electrochemical behaviour of Fe3O4/SPEEK in 0.1 M of phosphate buffer solution (PBS) containing 5 mM of potassium ferricyanide (III) solution (K3[Fe(CN)6]). An increase in peak current was observed at the nanocomposite modified electrode SPCE-Fe3O4/SPEEK) but not SPCE and SPCE-Fe3O4, which could be ascribed to the presence of SPEEK. CV and square wave voltammetry (SWV) were employed in the electroxidation of dopamine (0.1 mM DA). The detection limit (LoD) of 7.1 μM and 0.005 μA/μM sensitivity was obtained for DA at the SPCE-Fe3O4/SPEEK electrode with concentrations ranging from 5–50 μM. LOD competes well with other electrodes reported in the literature. The developed sensor demonstrated good practical applicability for DA in a DA injection with good resultant recovery percentages and RSDs values.

chemistry, multidisciplinary,biochemistry & molecular biology
Electrocatalytic determination of levodopa in presence of cabergoline using carbon paste electrode modified with graphene quantum dots/2-chlorobenzoyl ferrocene/ionic liquid

Peyman Mohammadzadeh Jahani

DOI: https://doi.org/10.5599/jese.1133

2021-11-17

Journal of Electrochemical Science and Engineering

Abstract:The electrochemical sensor was fabricated for the simultaneous determination of levodopa and cabergoline using carbon paste electrode (CPE) modified with graphene quantum dots (GQD), 2-chlorobenzoyl ferrocene (2CBF) and ionic liquid (IL). Then, the electrochemical behavior of levodopa alone and simultaneously with cabergoline at the surface of GQDs/2CBF/IL/CPE was investigated in phosphate buffer solution (PBS). Under optimal PBS, pH=7 condition, oxidation peak current has been found proportional to levodopa concentration in the range between 0.07 μM and 500.0 μM, with the limit of detection (LOD) of 0.02 μM (S/N=3). Outputs showed that at GQDs/2CBF/IL/CPE surface, the levodopa and cabergoline oxidation peaks are separated by the potential difference of 200 mV. In addition, it was found that this modified electrode possesses acceptable sensitivity, selectivity, stability and repeatability. All these properties were sufficient to allow simultaneous detection of levodopa and cabergoline in real samples at the surface of GQDs/2CBF/IL/CPE. This was supported by the successful application of this electrochemical sensor electrode for the determination of levodopa and cabergoline in urine, serum, and cabergoline tablets.
Atomically-dispersed manganese anchored on B,N co-doped carbon for the sensitive electrochemical detection of levodopa

Fan Wang,Junhua Li,Xiangxiong Chen,Hao Feng,Huiyang Liao,Jinlong Liu,Dong Qian,Geoffrey I.N. Waterhouse

DOI: https://doi.org/10.1016/j.cej.2024.148607

IF: 15.1

2024-01-10

Chemical Engineering Journal

Abstract:Metal single-atom catalysts offer the dual advantages of high electrochemical activity and near 100 % metal atom utilization, leading to their potential use in low-cost electrochemical sensor development. Herein, a novel electrocatalyst comprising atomically-dispersed Mn on B,N co-doped bamboo-derived carbon (MnSAs-BN-BC) was synthesized via a facile pyrolysis procedure. A high dispersion of Mn single atoms in MnSAs-BN-BC was confirmed by aberration-corrected transmission electron microscopy and elemental mapping. The Mn loading in the MnSAs-BN-BC determined by inductively coupled plasma mass spectrometry was 255 mg kg −1 . MnSAs-BN-BC displayed outstanding electrocatalytic performance for levodopa (LD) oxidation, allowing a robust electrochemical sensing platform for LD detection to be established. The MnSAs-BN-BC/GCE sensing platform offered a wide LD detection range (concentrations from 2 to 683 μM) and a very low limit of detection (LOD) of 0.45 μM, outperforming almost all electrochemical sensors reported to date for LD sensing. The MnSAs-BN-BC/GCE platform also featured outstanding repeatability, reproducibility, selectivity, and stability. The as-developed sensing platform was successfully applied to LD quantification in commercial tablets with satisfactory recoveries (85.2–102.4 %), with the analytical precision of method validated against a traditional UV–vis spectrophotometry method. Density functional theory (DFT) calculations showed that Mn single atom sites lowered the reaction energy barrier for LD oxidation, with the favorable d-band center position of Mn single atom sites in MnSAs-BN-BC contributing to the enhanced LD sensing performance. This work encourages the use of single-atom metal catalysts in design of high-performance electrochemical sensors for the rapid detection of LD.

engineering, chemical, environmental
Development of an efficient electrochemical sensor based on CuAl-LDH using an electrostatic repulsion approach for the selective determination of dopamine in the presence of uric acid and ascorbic acid species

Saeedeh Shahparast,Karim Asadpour-Zeynali

DOI: https://doi.org/10.1016/j.elecom.2024.107756

IF: 5.443

2024-05-21

Electrochemistry Communications

Abstract:This study provides a unique electrochemical sensor that exhibits both excellent sensitivity and selectivity, while also being environmentally friendly. The CuAl-LDH/GCE sensor, proposed as the recommended sensor, was synthesized using a straightforward one-step co-precipitation procedure. It was first used to measure dopamine levels using differential pulse voltammetry. At the ideal pH level of 8, dopamine has a positive charge, but ascorbic acid and uric acid have a negative charge. LDH, on the other hand, carries a negative charge and exhibits high electrostatic attraction towards dopamine, but is electrostatically repelled by negatively charged ascorbic acid and uric acid. Hence, CuAl-LDH/GCE has the potential to specifically ascertain the existence of dopamine in the presence of these particular species. The examination of the composition and morphology of CuAl-LDH was conducted using various analytical techniques, including scanner electron microscopy (FESEM), transmission electron microscope (TEM), element mapping (MAP), Fourier transform infrared (FTIR), energy-dispersive X-ray spectroscopy (EDX), Brunauer Emmett Teller (BET), X-ray photoelectron diffraction (XRD), and Raman techniques. Under ideal circumstances, the calibration graph of dopamine was generated using differential pulse voltammetry. A linear range of 4.194–1151.54 μM was achieved for dopamine, with a limit of detection of 0.33 μM. The findings of the study indicate that the sensor created for dopamine determination has exceptional stability, repeatability, and reproducibility. The sensor that was presented was effectively used for the measurement of dopamine in both pharmaceutical ampoules and human plasma samples.

electrochemistry
Preparation of Keggin-type Polyoxomolybdate and its Application as Electrochemical Sensor for Detection of Levodopa

Miao Liu,Mingxuan Jia,E Yifeng,Zhuozhe Li,Donghui Li,

DOI: https://doi.org/10.20964/2021.10.21

IF: 1.541

2021-10-01

International Journal of Electrochemical Science

Abstract:In this study, a levodopa (LDA) electrochemical sensor based on Keggin-type polyoxometalate was constructed. First, the silicomolybdenum heteropoly acid SiMo12 imidazole was synthesized by hydrothermal method. Fourier transform infrared absorption spectrometry (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to characterize the synthetic material. Then the SiMo12 imidazole was dropped onto the surface of a glassy carbon electrode (GCE) to construct an electrochemical sensor for detecting LDA. The sensing interface of the modified electrode was studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Under the optimal experimental conditions, the constructed electrochemical sensor had good detection performance for LDA with a linear range of 1×10-7 mol/L ~ 8×10-6 mol/L and a limit of detection (LOD) of 0.48×10-7 mol/L. Satisfactory results were also obtained in the detection of LDA tablets.

electrochemistry
Development of molybdenum trioxide based modified graphite sheet electrodes for enhancing the electrochemical sensing of dopamine

Fatimah Saeed Aldughaylibi,Hidayath Ulla,Nassiba Allag,Mir Waqas Alam,Amal BaQais,Mohd Al Saleh Al-Othoum,Shima Sadaf

DOI: https://doi.org/10.1016/j.mssp.2024.108107

IF: 4.1

2024-04-01

Materials Science in Semiconductor Processing

Abstract:Electrochemical detection of dopamine is crucial in the early stages of Parkinson's and Alzheimer's disease diagnosis. In this paper, we have developed modified electrodes based on molybdenum oxide (MoO3) grown on graphite sheet (GS), which was investigated for its ability to detect dopamine sensitively and selectively. The MoO3/GS electrodes were prepared by thermal evaporation of MoO3 on GS sheets followed by annealing at different temperatures (RT and annealing temperatures of 100 °C, 200 °C, 300 °C, 400 °C and 500 °C). The electrodes were analysed using XRD, Raman, FESEM and HRTEM. Compared to other electrodes, the modified MoO3/GS electrode annealed at 500 °C showed more significant charge transfer and increased selectivity and sensitivity in the electrochemical detection of dopamine. The findings showed a significant sensitivity of 85.71 μA. μM−1·cm−2 for the linear range of 1–10 nM and the lowest detection limit of 2.71 nM were achieved from the dopamine sensing. The developed electrode successfully detected dopamine in human blood serum and urine samples with respectable recovery rates.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Electrochemical method for determination of levodopa in the presence of uric acid using In2S3 nanospheres on 3D graphene-modified ITO glass electrode

Xinrui Guo,Hongyan Yue,Shuo Huang,Xin Gao,Hongtao Chen,Pengfei Wu,Teng Zhang,Zengze Wang

DOI: https://doi.org/10.1007/s10854-020-03925-3

2020-07-10

Abstract:An electrochemical sensor that can sensitively detect levodopa without fragile and expensive antibodies has been prepared on the basis of indium sulfide and graphene. The indium sulfide nanospheres synthesized by a hydrothermal method were grown on the surface of three-dimensional graphene prepared by chemical vapor deposition. The graphene maintains a good 3D structure and the indium sulfide nanospheres increases the specific surface area of graphene. The composite possesses a low detection limit of 87 nM (S/N = 3) and the sensitivity of it reaches 1.98 μA μM−1 cm−1. Also, good electrochemical performance, selectivity, and stability make it available to be used for detecting real biomolecules.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied

A loss-of-function mutation in the CFC domain of TDGF1 is associated with human forebrain defects

Minimal-Invasive Levodopa Sensing Based on Differential Amperometry Microneedle Electrodes Decorated with Spike-like Au Nanoparticles

Differential Amperometric Microneedle Biosensor for Wearable Levodopa Monitoring of Parkinson's Disease

Differential Coulometry Based on Dual Screen-Printed Strips for High Accuracy Levodopa Determination Towards Parkinson's Disease Management

Electrochemical Determination of Dopamine Using a Carboxyl-functionalized Carbon Nanotube-Modified Carbon Paste Electrode Doped with Polymeric Ferric Sulfate

Study on Levodopa Sensor Modified by Ti<sub>3</sub>C<sub>2</sub> MXene

Eu2O3@Cr2O3 Nanoparticles-Modified Carbon Paste Electrode for Efficient Electrochemical Sensing of Neurotransmitters Precursor L-DOPA

Smartphone-based differential pulse amperometry system for real-time monitoring of levodopa with carbon nanotubes and gold nanoparticles modified screen-printing electrodes

A Sensitive Photoelectrochemical Sensor for Levodopa Detection Using Benzothiadiazole-Based Conjugated Microporous Polymer-Coated Graphene Heterostructures

[The clinical effect of intravenous regional sympathectomy with guanethidine in the management of sympathetically maintained pain].

In-situ anchoring bimetallic nanoparticles on covalent organic framework as an ultrasensitive electrochemical sensor for levodopa detection

Electrochemical determination of levodopa using ZnO nanowire arrays/graphene foam

Biosensor Strip for Rapid On‐site Assessment of Levodopa Pharmacokinetics along with Motor Performance in Parkinson's Disease

A Critical Overview of Enzyme-Based Electrochemical Biosensors for L-Dopa Detection in Biological Samples

Electrochemical Detection of Dopamine at Fe3O4/SPEEK Modified Electrode

Electrocatalytic determination of levodopa in presence of cabergoline using carbon paste electrode modified with graphene quantum dots/2-chlorobenzoyl ferrocene/ionic liquid

Atomically-dispersed manganese anchored on B,N co-doped carbon for the sensitive electrochemical detection of levodopa

Development of an efficient electrochemical sensor based on CuAl-LDH using an electrostatic repulsion approach for the selective determination of dopamine in the presence of uric acid and ascorbic acid species

Preparation of Keggin-type Polyoxomolybdate and its Application as Electrochemical Sensor for Detection of Levodopa

Development of molybdenum trioxide based modified graphite sheet electrodes for enhancing the electrochemical sensing of dopamine

Electrochemical method for determination of levodopa in the presence of uric acid using In2S3 nanospheres on 3D graphene-modified ITO glass electrode