Abstract:In the recycling field of lithium-ion batteries (LIB), the hydrometallurgical method has attracted lots of attention in recent years due to its high productivity, low cost and wide applicability. Tremendous effort has been made to improve design and control of manufacturing process to enable a stable and high-quality output. It is clear that the impurities introduced during the recycling process could pose a major impact on the final recovered materials in a variety of aspects. In particular, there are three types of impurities remained in the leaching solution. First, cations such as Al 3+ , Cu 2+ and Fe 3+ which come from dissolved metal debris, battery cases or current collectors for instance. Second, anions like F - , S 2- and PO 4 3- which are introduced from electrode materials or electrolyte salts. Lastly, neutral insoluble substances, for example, carbon particles that are added during the manufacturing process. In our work, systematic investigation has been carried out to explore the influence of different impurities on the recovered NCM622 cathodes via hydrometallurgical approach. It is found that different types of impurities have a unique impact on the cathode properties, and, even extraordinary when they are at certain concentration level. In general, cations have obvious negative impacts on cathode morphology and powder density because of the reaction with OH - in alkaline environment which interferes with the nucleation and growth of precursors. Ultimately, it is very likely to obtain cathodes with irregular particle shapes, reduced sizes and poor tap densities under a high concentration of cation impurities. In these aspects, on the contrary, anions and insoluble substances cause little side effects on the recovered materials. It is noted that the presence of some anions during the co-precipitation, fluoride ions for example, could promote the formation of holes inside particles which can be beneficial to the electrochemical performance of the cathodes. No crystallinity damage or heterogeneous element distribution have been confirmed within as-prepared cathode materials, indicating that a limited range of impurity (maximum 5 at% in our work) could not affect the overall periodicity and consistency in the materials. However, extra phases could be detected in some cathodes when impurity level reaches 5 at%. The excess amount of cation impurities prevents uniform precipitation, resulting in the creation of extra phase Li 2 MnO 3 in the cathodes. Besides, a special extra phase of Li 3 PO 4 exists under the presence of PO 4 3- ions due to the reaction with lithium salt during sintering. Other impurities such as carbon and fluorine do not show similar mechanism. Extra phases in the cathodes will trigger a considerable deterioration in the electrochemical performance which needs to be avoided. Thus, special attention is required when impurity concentration exceeds 1 at% level, especially for cations. According to the analysis, some impurity elements could merge into the cathode lattice. Cations like Al 3+ and Cu 2+ form metal hydroxides during the precursor synthesis, then they are incorporated into the cathodes by occupying the sites of transition metals. A small amount of replacement (< 1 at%), on Ni 2+ in particular, could inhibit the cation mixing in the cathodes which results in an improved material quality. In addition, fluoride ion inclusion occurs by the substitution for oxygen in cathodes. This phenomenon not only lowers the average oxidation state of Ni ions, but also raises the lithium diffusivity in the cathodes which significantly increases the cathode capacity and rate performance. In contrast, impurities like carbon nano-particles and PO 4 3- do not have clear interactions with the cathode lattice. At 1 at% impurity level, NCM622-Cu shows the highest discharge capacity of 170 mAh/g after 100 cycles at 0.33C (1C = 175 mAh/g). Under the positive influence of fluorine, the cathode NCM622-F also presents a high discharge capacity of 167 mAh/g after 100 cycles at 0.33C which is about 8% better than that of virgin. In terms of Al 3+ impurity, 1 at% of NCM622-Al still maintains a similar performance that is comparable to the virgin counterpart. However, 1 at% of carbon impurity has a clear adverse effect on the cathode performance and such a level of ion impurities leads to an even worse deterioration in the properties of recovered NCM622-Fe. To sum up, the characteristics of recovered cathodes via hydrometallurgical process could achieve different levels of variation, either positive or negative at one particular aspect, due to the effects from impurity within certain concentration range. Thus, it is i -Abstract Truncated-

Al Impurity Upcycled High-Voltage Cathodes from Spent LiCoO2 Batteries

Can Aluminum Impurity from Current Collectors Upgrade Spent Li1‐xCoO2 into a High‐Performing Cathode for Lithium‐Ion Batteries?

A Universal Molten Salt Method for Direct Upcycling of Spent Ni‐rich Cathode Towards Single‐crystalline Li‐rich Cathode

Mechanochemical upcycling of spent LiCoO2 to new LiNi0.80Co0.15Al0.05O2 battery: An atom economy strategy

Sustainable Upcycling of Spent LiCoO2 to an Ultra-Stable Battery Cathode at High Voltage

Direct Upcycling of Degraded LiCoO2 Material Toward High‐Performance Single‐Crystal NCM Cathode

Closed-Loop Direct Upcycling of Spent Ni-Rich Layered Cathodes into High-Voltage Cathode Materials

Impurity removal with highly selective and efficient methods and the recycling of transition metals from spent lithium-ion batteries

Recycling of spent LiCoO2 materials by electrolytic leaching of cathode electrode plate

Direct conversion of degraded LiCoO2 cathode materials into high-performance LiCoO2: A closed-loop green recycling strategy for spent lithium-ion batteries

Direct conversion of degraded LiCoO<sub>2</sub> cathode materials into high-performance LiCoO<sub>2</sub>: A closed-loop green recycling strategy for spent lithium-ion batteries

Converting spent lithium cobalt oxide battery cathode materials into high-value products via a mechanochemical extraction and thermal reduction route

Subtractive transformation of cathode materials in spent Li-ion batteries to a low-cobalt 5 V-class cathode material

In Situ Constructed Spinel Layer Stabilized Upcycled LiCoO2 for High Performance Lithium‐Ion Batteries

Innovative Electrochemical Strategy to Recovery of Cathode and Efficient Lithium Leaching from Spent Lithium-Ion Batteries

Extraction of Li and Co from industrially produced Li-ion battery waste - Using the reductive power of waste itself

Short-Process Regeneration of Highly Stable Spherical LiCoO2 Cathode Materials from Spent Lithium-Ion Batteries through Carbonate Precipitation

Cation doping method for the restoration of spent LiNi1/3Co1/3Mn1/3O2 cathode material properties

Homogenization and Upcycling of Hetero Spent LiCoO2 Cathodes: Rational Introduction of Li/Co Anti‐Sites Toward Enhanced High‐Voltage Stability

Selective lithium extraction and regeneration of LiCoO2 cathode materials from the spent lithium-ion battery

Different Effects of Impurities on Recovered Cathode Materials from Hydrometallurgical Recycling