Social Goals and the Valuation of Natural Capital

R. Costanza

DOI: https://doi.org/10.1023/A:1024045221992

2003-07-01

Abstract:

What problem does this paper attempt to address?

Adsorptive Oxidation of Aqueous Sulfide Onto Zerovalent Cobalt and Magnetite-Supported Biochars: Insights into Synthesis and Mechanistic Performance

Umar Abdulbaki Danhassan,Hongjian Lin,Xin Zhang,Riying Qi,Mahmoud H. Ali,Kuichuan Sheng

DOI: https://doi.org/10.2139/ssrn.4388913

2023-01-01

Abstract:Pristine biochar (PBC) has gained increasing attention in adsorptive oxidation due to its redox-active moieties. However, its application for removing aqueous sulfide (S2-) is limited because it lacked conductive and mesoporous structure required to transport S2- to active sites and tradeoff between mesopores, conductive structure, and redox-active sites during synthesis remains elusive. Here, cobalt or iron ion is impregnated in biomass to elucidate the mechanism of biochar structure formation and performance in removing S2- from water. The finding suggests cobalt and iron ions facilitate biomass decomposition to remove volatile matter, which transformed them into elemental cobalt (Co0) and magnetite (Fe3O4) on biochars (BC-Co) or (BC-Fe) and improved the porous structure. BC-Co removed S2- more than PBC and BC-Fe under different pH, competing ions, and during regenerations of adsorbents. BC-Co befitted from superior mesopores to adsorb S2- 2.4 and 35 times faster than PBC and BC-Fe, achieving 811 Â±146 mg-S2-/g maximum capacity. BC-Fe removed S2- far less than PBC because Fe3O4 on its surface blocked S2- diffusion channel to the active site. It is postulated that S2- transfers from bulk liquid to film near the biochar pore and enters the pores via pore and surface diffusion to the active site, where it is adsorbed and oxidized. S2- was oxidized to elemental sulfur or sulfate by quinone, semiquinone or hydroxyl radicals at the wall of the pore of biochars. This study has documented fundamental information for developing more on-demand porous, conductive and electroactive biochar for removing redox active contaminants.
Carbon nanosheets composited with MgO/CaO prepared by one-step co-pyrolysis strategy for efficient H 2 S oxidation at room temperature

Kunlin Li,Xueyan Chen,Xiaoxiao Qin,Min Chen,Jianghao Zhang,Kai Li,Fei Wang,Jinhou Fang,Changbin Zhang

DOI: https://doi.org/10.1016/j.seppur.2023.125790

IF: 8.6

2023-11-24

Separation and Purification Technology

Abstract:Carbon nanosheets have promising application in desulfurization but are challenged by high cost and cumbersome preparation process. In this work, carbon nanosheets composited with CaO and MgO (Mg x Ca y /C) were fabricated by one-step co-pyrolysis of magnesium gluconate and calcium gluconate. This carbon nanosheets material enables the efficient room temperature H 2 S oxidation in a moist atmosphere. The characterization results indicate that this co-pyrolysis strategy produces defect-rich carbon nanosheets with uniformly distributed oxides nanoparticles for the adsorption and activation of H 2 S as well as O 2 . Significantly, numerous nanoholes with a size of 5–20 nm are obtained on the carbon nanosheets, which serve as S storage space to form S polymer resistant to further oxidation, inhibiting the formation of H 2 SO 4 and its subsequent consumption of active components. As a result, the Mg 1 Ca 9 /C shows a tremendous H 2 S capacity of 858.5 mg/g cat. . In addition, the processes of H 2 S oxidation over the Mg x Ca y /C and its deactivation are also detailly illustrated. This study contributes to providing a low-cost and facile preparation approach for carbon nanosheets in desulfurization and other diverse applications.

engineering, chemical
Adsorption Mechanism and Regeneration Performance of Calcined Zeolites for Hydrogen Sulfide and Its Application

Xianghao Zha,Feixing Li,Bo Feng,Xin Zhang,Ruo He

DOI: https://doi.org/10.1021/acsomega.4c00987

IF: 4.1

2024-01-01

ACS Omega

Abstract:Hydrogen sulfide (H2S) is a very toxic, acidic, and odorous gas. In this study, a calcined zeolite was used to investigate the adsorption performance of H2S. Among particle size, calcination temperature and time calcination temperature and time had significant effects on the adsorption capacity of H2S on the zeolite. The optimal calcination conditions for the zeolite were 332 degrees C, 1.8 h, and 10-20 mm size, and the maximum adsorption capacity of H2S was approximately 6219 mg kg(-1). Calcination could broaden the channels, remove the adsorbed gases and impurities on the surface of zeolites, and increase the average pore size and point of zero net charge. As the zeolite adsorbed to saturation, it could be regenerated at the temperatures between 200 and 350 degrees C for 0.5 h. Compared with the natural zeolite, the adsorption capacities of dimethyl disulfide, dimethyl sulfide, toluene, CH3SH, CS2, CO2, and H2S were significantly higher on the calcined zeolite, while the adsorption capacity of CH4 was lower on the calcined zeolite. A gas treatment system by a temperature swing adsorption-regeneration process on honeycomb rotors with calcined zeolites was proposed. These findings are helpful for developing techniques for removing gas pollutants such as volatile sulfur compounds and volatile organic compounds to purify biogas and to limited toxic concentrations in the working environment.
Preparation of sludge-straw-based activated carbon and its adsorption of H2S

Fan ZENG,Xiaofeng LIAO,Yong LI,Ying HE,Li LIAO,Hui HU

DOI: https://doi.org/10.13671/j.hjkxxb.2017.0170

2017-01-01

Abstract:Sewage sludge and corn straw were used to prepare sludge-straw activated carbon (AC) by pyrolysis with KOH.This study investigated the effects of mixing ratio (sludge/straw) and the amount of KOH on physical and chemical properties of the sludge-straw activated carbon.The activated carbon named C372 was prepared with the mixing ratio of sludge ∶straw ∶activator of 3∶7∶2.The nicroporosity of the C372 was up to 0.59,and the specific surface area reached 369.271 m2.g-1.The experimental results showed that activated carbon C372 had the highest breakthrough sulfur capacity and saturated sulfur capacity of 5.82 and 7.00 mg H2S per gram AC,respectively.The presence of the lactone groups on the activated carbon was not conducive to its adsorption to H2S.The SEM and BET characterization analysis showed that the specific surface area of activated carbon increased as the increase of the proportion of straw in the raw material and the ACs' adsorption capacity of H2S.Activated carbon C372 has good regeneration performance,and the breakthrough sulfur capacity and saturated sulfur capacity can be restored more than 55％ after the second cycle.
The Efficiency and Mechanism of Humidity in Alleviating CO2 Inhibition on H2S Adsorption to Straw Biochars

Dandan Huang,Mingshen Liang,Ning Wang,Qiyong Xu

DOI: https://doi.org/10.1016/j.envres.2022.113008

IF: 8.3

2022-01-01

Environmental Research

Abstract:Adsorption tests were conducted to clarify the impact of carbon dioxide (CO2) on hydrogen sulfide (H2S) removal to straw biochars and the role of humidity in affecting the CO2 impact. When straw biochars were dry, CO2 proved significantly detrimental to their H2S adsorption, regardless of the CO2 contents. In contrast, when adjusting the humidity of the biochars to 20%, the presence of CO2 promoted the conversion of H2S into sulfites, though still inhibited the generation of elemental sulfur, through which the original negative CO2 impact was nearly compensated. The presence of low to medium contents of CO2 even slightly improved the adsorption capacity and extended the breakthrough time. This phenomenon was ascribed to a favorable carbon surface environment for H2S dissociation and oxidation, created from the reactions of the major minerals (Ca and Mg) with CO2 and water. To sum up, the CO2 inhibition on the H2S adsorption to biochars was ascribed to the competition of CO2 for the active sites; however, humidity induced a series of CO2-participated chemical reactions between H2S and the minerals, sufficiently alleviating the CO2 inhibition. The results also highlight the necessity to recognize the most critical biochar properties or an efficient balance of crucial biochar properties in achieving an optimal H2S removal when CO2 is present in the syngas.
Bamboo Derived Activated Carbon As Highly Efficient Catalysts for the Oxidation and Adsorption of Hydrogen Sulfide at Room Temperature

Shi Du,Xin Liu,Yue Liu,Junhao Wang,Dongxu Liu,Jianxiao Yang,Xin Zhang

DOI: https://doi.org/10.2139/ssrn.4389448

2023-01-01

Abstract:Bamboo derived activated carbon exhibited excellent sulfur capacity for H2S catalytic oxidation–adsorption at room temperature. Diffusion inside the pores was the rate-determining step during the diffusion process of sulfur-containing products.
Towards Highly Exposed Active Sites Via Edge-N-rich Carbon Nanosheet @ Porous Biochar for Efficient H2S Catalytic Oxidation

Lin Chen,Xia Jiang,Shenggui Ma,Wenhua Chen,Bo Xu,Zhongde Dai,Wenju Jiang,Yue Peng,Junhua Li

DOI: https://doi.org/10.1016/j.cej.2023.146115

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:In this study, Edge-N-rich carbon nanosheet @ porous biochar (NCN@PB) was synthesized successfully from waste biomass self-assembly in a simple and green approach. The accessible and efficient utilization of edge-N enriched on the surface, together with the hybrid structure of NCN@PB improved the H2S oxidation capacity up to 390.1 mg/g at room temperature, reflecting an 8-fold enhancement compared with the blank biochar. The Density functional theory calculation, in-situ DRIFTS, and the characterization results further uncovered the desulfurization mechanism of active sites. Edge-N species decreased the barriers in critical steps governing H2S catalytic oxidation, i.e., H2S dissociation and O2 activation, especially the pyrrolic N. This strategy is beneficial for the development of surface engineering on metal-free catalysts and provides a new idea for improving the catalytic combustion activity of N-doped biochar.
Self-supporting nano-porous carbon nanosheet with organized sp2-C network for unprecedented catalytic performance in room-temperature H2S oxidization

Feng Hu,Huan Chen,Zhengliang Zhang,Bo Niu,Yayun Zhang,Donghui Long

DOI: https://doi.org/10.1039/d3ta00822c

IF: 11.9

2023-04-14

Journal of Materials Chemistry A

Abstract:Graphene-based carbons have promising applications in non-metal catalysis but are challenged by interlayer stack and poor porosity. Herein, the concept of graphene-like carbons is proposed with porous carbon nanosheets (PCNs) being prepared via a melt-foaming strategy. PCNs show abundant pore structure and organized sp 2 -C network around nanopores. Moreover, the robust and curved nanosheet is spatially isolated and is thus totally stack-free. The unimpeded accessibility to functional groups, defects, and sp 2 -C network enables PCNs with outstanding activity of activating oxygen and high compatibility as carbon support. Thus, alkali-modified PCNs present appealing catalytic oxidation of hydrogen sulfide with unprecedented sulfur capacity up to 10.7 g H 2 S g −1 catalyst, 3-fold than that of graphene-based benchmark counterparts. This study provides new insights into the rational design of next-generation carbon catalysts, opening up exciting opportunities for diverse applications.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Carbon-Rich carbon nitride nanocatalysts for H2S selective oxidation

Shihuan Lyu,Weiting Wu,Rui Xiong,Can Yang,Baisheng Sa,Jinshui Zhang,Yidong Hou,Xinchen Wang

DOI: https://doi.org/10.1016/j.jcat.2022.08.011

IF: 7.3

2022-09-01

Journal of Catalysis

Abstract:Selective catalytic oxidation (SCO) of hydrogen sulfide (H2S) to sulfur exhibits significant advantages for H2S removal, including high efficiency, mild operating conditions and thermodynamic unlimitation for H2S removal. Recently, polymeric carbon nitride (PCN) has emerged as a candidate for H2S selective oxidation reactions, benefiting from its aromatic C-N hybridized π-conjugated system for H2S adsorption/dissociation and good sulfur tolerance. However, its performance is greatly hampered by the lack of sufficient surface active sites for O2 adsorption and activation. Herein, we demonstrate that the incorporation of carbon atoms in PCN matrix to constructure carbon-rich carbon nitride nanosheets is a facile strategy to advance the desulfurization performance. The carbon atoms uniformly incorporated in PCN backbones can effectively extend the aromatic π-conjugated electronic system and create abundant oxygen-containing functional groups on the surface. The improved electronic configurations and surface properties are beneficial for the adsorption and activation of H2S and O2. In addition, the nanosheet morphology favors for increasing the surface area of the material, thereby promoting the mass transfer of H2S and O2 during the desulfurization process. The optimized carbon-rich carbon nitride nanosheets exhibit a H2S conversion of 99% and a S selectivity up to 95% for H2S selective oxidation at 200 °C, and the reaction is not restricted by mass transportation and heat transfer at such a high conversion rate. This synthetic strategy allows ample choice of low-cost and easy-available organic precursors for the large-scale production of the desulfurization catalysts.

chemistry, physical,engineering, chemical
[Advances in Mechanism and Influencing Factors Affecting Hydrogen Sulfide Adsorption by Biochar].

Qi-Yong Xu,Ming-Shen Liang,Wen-Jun Xu,Dan-Dan Huang

DOI: https://doi.org/10.13227/j.hjkx.202102035

2021-01-01

Abstract:Hydrogen sulfide(H2S) is one of the most common gas products from modern industrial processes. It is highly toxic, corrosive, and polluting, and poses harm to both the natural environment and human health if it is not properly removed. Biochar has been widely applied for the treatment of environmental pollution due to its excellent adsorption ability, low cost, and wide choice of source materials. Currently, although studies on hydrogen sulfide adsorption by biochar have attracted increasing attention, the factors involved are complex and varied, leading to a necessity to review and summarize the available knowledge and advances. To bridge the research gap, this paper presents the advances in H2S adsorption by biochar, including properties, influencing factors(i.e., biomass feedstock, pyrolysis temperature, residence time, and particle size), control measures(i.e., humidity, adsorption temperature, operating conditions, and modification of biochar by activation), and adsorption mechanism. The work will provide further reference for the preparation and optimization of biochar adsorption conditions to realize a highly efficient removal of H2S.
Towards highly exposed active sites via Edge-N-rich carbon nanosheet @ porous biochar for efficient H 2 S catalytic oxidation

Lin Chen,Xia Jiang,Shenggui Ma,Wenhua Chen,Bo Xu,Zhongde Dai,Wenju Jiang,Yue Peng,Junhua Li

DOI: https://doi.org/10.1016/j.cej.2023.146115

IF: 15.1

2023-09-23

Chemical Engineering Journal

Abstract:In this study, Edge-N-rich carbon nanosheet @ porous biochar (NCN@PB) was synthesized successfully from waste biomass self-assembly in a simple and green approach. The accessible and efficient utilization of edge-N enriched on the surface, together with the hybrid structure of NCN@PB improved the H 2 S oxidation capacity up to 390.1 mg/g at room temperature, reflecting an 8-fold enhancement compared with the blank biochar. The Density functional theory calculation, in-situ DRIFTS, and the characterization results further uncovered the desulfurization mechanism of active sites. Edge-N species decreased the barriers in critical steps governing H 2 S catalytic oxidation, i.e., H 2 S dissociation and O 2 activation, especially the pyrrolic N. This strategy is beneficial for the development of surface engineering on metal-free catalysts and provides a new idea for improving the catalytic combustion activity of N-doped biochar.

engineering, chemical, environmental
Cu Nanoparticles Inlaid Mesoporous Carbon Aerogels as a High Performance Desulfurizer.

Jiang Wu,Siyuan Yang,Qizhen Liu,Ping He,Huan Tian,Jianxing Ren,ZhenZhen Guan,Tao Hu,Bu Ni,Chong Zhang

DOI: https://doi.org/10.1021/acs.est.5b03740

IF: 11.4

2016-01-01

Environmental Science & Technology

Abstract:In the present study, to insert the Cu nanoparticles (NPs) into mesoporous carbon aerogels and first applied it to remove H2S efficiently. This desulfurizer was made based on the dimensional policy by inserting the Cu NPs on mesoporous carbon aerogels to overcome the sintering problem and improve the activity, which has potential performance at high-temperature catalysis. The obtained desulfurizer was employed for H2S removal at middle temperature conditions (optimal H2S adsorption at 550 degrees C). We explored the optimum doping amount of CuOx, optimum temperature conditions, and the influence of textural parameters of carbon aerogels. The desulfurizers were characterized by means of field emission scanning electron microscopy (FESEM), N-2-adsorption, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), H-2 temperature-programmed reduction (H-2-TPR), and Raman spectra techniques. The results confirmed that the presence of H-2 was unfavorable for sulfidation and obviously shortened the breakthrough time. However, the existence of CO had little impact on the desulfurization and sulfur capacity. In a nutshell, this work could provide a new synthetic route to prepare Cu NPs deep into the lattice of carbon aerogels structure of desulfurizers and understand the desulfurization mechanism.
Preparation and Characterization of Cu(NO3)2 Modified Activated Carbon Adsorbents and Influencing Factors of H2S Adsorption

Jiaojing Zhang,Mei Zhang,Yanxiu Liu,Xueqin Wang,Yuanyuan Wang

DOI: https://doi.org/10.2174/2405520416666230308153305

2023-03-08

Recent Innovations in Chemical Engineering (Formerly Recent Patents on Chemical Engineering)

Abstract:Background: With the constant development and growth of the world’s economy, the demand for energy continues to rise. However, rising oil prices, increasing carbon emissions, and energy shortages will limit economic development and affect living standards. Therefore, further exploitation and utilization of natural gas are of great significance for the sustainable development of national economies and the improvement of civil life. Objective: Natural gas contains acidic gas, such as hydrogen sulfide (H2S), and can lead to physical safety issues, environmental pollution, equipment corrosion, and catalyst poisoning. Therefore, a desulfurization process, which has practical significance, must be carried out to reduce the H2S content to less than 20 mg•m−3. Methods: Currently, the main desulfurization processes involve dry and wet desulfurization methods. The wet desulfurization methods include physical, chemical, and physico-chemical solvent methods, which have a large processing capacity and involve a continuous operation sequence applied to the purification of natural gas containing a high sulfur content. The dry desulfurization methods, which use a solid as the desulfurizer, have high precision, easy operation, and low energy consumption. This method has been widely applied to advanced treatment. Activated carbon, which has a large surface area, large pore volume, and complex porous structure, is widely used as an adsorbent for desulfurization. When compared with other adsorbents, activated carbon has several advantages, such as a high adsorption capacity and low cost. The H2S removal performance of the adsorbent can be significantly improved after modification. In this study, using a low concentration of H2S and nitrogen to simulate raw fuel gas, cupric nitrate-modified activated carbon was used as the main adsorbent for desulfurization. The effect of the preparation conditions on the H2S removal performance was studied, and the adsorbents were characterized using a series of methods. method: Adsorption desulfurization Results: In this study, a low concentration of H2S and nitrogen were used to simulate raw fuel gas, and cupric nitrate-modified activated carbon was used as an adsorbent. The results from structural analysis indicated a significant change in the surface structure of AC by introducing Cu(NO3)2. Cu(NO3)2 promoted the transformation of micropores into mesopores or macropores and active substances into the pores of AC for desulfurization. The effects of the preparation conditions on the H2S removal performance were studied using a fixed-bed adsorption column. The best preparation conditions for the Cu(NO3)2 modified activated carbon adsorbent involved: a Cu(NO3)2 impregnation concentration of 5%, impregnation time of 24 h, calcination temperature of 300 C, and calcination time of 2 h. The H2S saturation capacity and desulfurization rate reached 55.4 mg•g−1 and 98.92%, respectively. The H2S saturation capacity was improved by 38.2 mg•g−1 compared with unmodified activated carbon. result: In this paper, using a low concentration of H2S and nitrogen to simulate raw fuel gas, cupric nitrate modified activated carbon was used as the main adsorbent for desulfurization. The effect of the preparation conditions on the H2S removal performance was studied and the adsorbents characterized using a series of methods. Conclusion: In this study, a low concentration of H2S and nitrogen were used to simulate raw fuel gas, and cupric nitrate-modified activated carbon was used as an adsorbent. The experimental results showed that the H2S removal performance of the adsorbent was significantly improved using Cu(NO3)2 impregnated activated carbon. other: Without
A Sustainable Design of ZnO-based Adsorbent for Robust H2S Uptake and Secondary Utilization As Hydrogenation Catalyst

Chao Yang,Song Yang,Hui-Ling Fan,Jian Wang,Hui Wang,Ju Shangguan,Chao Huo

DOI: https://doi.org/10.1016/j.cej.2019.122892

IF: 15.1

2020-01-01

Chemical Engineering Journal

Abstract:Low sulfur capacity and low regeneration performance are the long-time problems in the industrial application of ZnO-based adsorbents for ambient H2S removal. However, no efficient approach has been reported up to now to simultaneously solve these two problems. With the increasingly stringent environmental regulations in China, a robust but sustainable ZnO-based adsorbent is strongly desired. Herein, we constructed such an adsorbent for the first time by introducing cobalt species into ZnO/SiO2 to form a heterostructured ZnO-Co3O4/SiO2 nanocomposite. For comparison, Co doped ZnO/SiO2 and Zn doped Co3O4/SiO2 were also fabricated. According to the breakthrough tests with initial H2S partial pressure of 57 Pa, the heterostructured ZnO-Co3O4/SiO2 adsorbent exhibited highest sulfur capacity of 188.4 mg S/g sorbent at breakthrough level of 1%, the corresponded partition coefficient (at 0.57 Pa, 303 K) was 10.3 mol. kg(-1). Pa-1. The introduced Co species not only improved the dispersion of ZnO nanograins, but also served as active sites for reacting and oxidizing H2S molecular. It also found that the formed ZnO-Co3O4 heterostructure could boost the hydroxylation of H2O, which provided an alkali environment for H2S dissociation. More meaningfully, this exhausted sorbent could be secondarily utilized as catalyst for carbonyl sulfide (COS) hydrogenation and exhibited 100% COS conversion even at a temperature lower than 200 degrees C, which was almost 3.3 times the conversion achieved by a commercial Co-Mo/Al2O3 catalyst (30%). This study will provide a new idea for rational design of metal oxide-based adsorbents to avoid causing secondary pollution by the spend adsorbents.
Polyethyleneimine-functionalized mesoporous carbon nanosheets as metal-free catalysts for the selective oxidation of H2S at room temperature

Jitong Wang,Chengyu Ke,Xianfeng Jia,Cheng Ma,Xiaojun Liu,Wenming Qiao,Licheng Ling

DOI: https://doi.org/10.1016/j.apcatb.2020.119650

2021-04-01

Abstract:Nitrogen-functionalized mesoporous carbon nanosheets are designed and constructed by supporting polyethyleneimine (PEI) on mesoporous carbon nanosheets. The carbon nanosheets possess a two-dimensional lamellar structure, interconnected mesoporous framework and highly dispersed PEI with considerable basic sites which work cooperatively to improve the desulfurization capability at room temperature. The appropriate residual pores after PEI loading provide a fast H2S diffusion channel, accessible interfacial area and storeroom for the product. Moreover, the nanosheet structure could shorten the diffusion pathway to promote the reaction kinetics. The nitrogen functional group of PEI as base sites is effective to enhance the interaction with H2S and facilitate its dissociation into HS−, resulting in a high breakthrough sulfur capacity of 13.68 mmol/g. A reaction mechanism by the combination of amine group promoted H2S dissociation and carbon induced O2 activation is proposed. This work raises the possibility of employing nitrogen-functionalized porous carbons as efficient catalyst for H2S selective oxidation.
Preparation of nitrogen-doped activated carbon used for catalytic oxidation removal of H 2 S

Shanjie Cheng,Tao Wang,Liang Chu,Jun Li,Liqiang Zhang

DOI: https://doi.org/10.1016/j.scitotenv.2024.170073

IF: 9.8

2024-01-21

The Science of The Total Environment

Abstract:In this study, nitrogen-doped modified activated carbons were synthesized for H 2 S removal from Zhuxi activated carbon and 4,4′-bipyridine as raw material and nitrogen source, respectively. The synthesis strategy was hydrothermal treatment and subsequent NH 3 annealing, and the formation and conversion patterns of the different N configurations were investigated. When the annealing temperatures were 500 °C and 600 °C, N-5 account for the majority. As the annealing temperature increased, the proportion of N-6 gradually increased. After the temperature increased to 1000 °C, N-5 and N-6 were converted to N-Q to a certain degree, while the amount of nitrogen doping decreased significantly. The sample H160-0.2-800 exhibited excellent H 2 S removal with a high sulfur capacity of up to 206.89 mg/g, significantly higher than that of the original activated carbon ZX1200 (67.56 mg/g). The reason for this is that the micropores ( V mic = 0.5155 cm 3 /g) and specific surface area ( S BET = 1369.5 m 2 /g) of the modified activated carbon are more developed than those of the original activated carbon. A high nitrogen content (3.14 wt%) and N-6 configuration proportion (73.56 %) are significant reasons for the excellent adsorption properties. The mechanism of the catalytic oxidation was investigated. The introduction of surface nitrogen-containing functional groups alkalizes the activated carbon surface, enhancing the adsorption and dissociation of H 2 S and O 2 and facilitating the formation of sulfur radicals and elemental sulfur.

environmental sciences
Study on the adsorption performance and regeneration of lignin-derived graphitic carbon for H 2 S

Fen Li,Ruiying Wang,Ying Yang,Menglong Zheng,Qiushuang Li,Dongdong Yang,Huiyu Chen

DOI: https://doi.org/10.1016/j.partic.2024.08.005

IF: 3.5

2024-08-18

Particuology

Abstract:s In pursuit of effective adsorption materials for malodorous gases such as H 2 S and to broaden the utilization avenues of lignin waste, this study employed the direct pyrolysis method to synthesize three types of alkali lignin graphitized carbons, namely C-800, KC-700, and KEC-700. Among them, KEC-700 exhibits a high specific surface area of 1672.9 m 2 /g, significantly superior H 2 S adsorption performance compared to other materials, an adsorption breakthrough time of up to 220 min, and a sulfur capacity of 67.1 mg/g. Structural analysis showed that the more oxygen-containing functional groups of lignin charcoal and the larger specific surface area facilitated the adsorption of H 2 S. After reaching adsorption saturation, the degree of graphitization of lignin carbon diminishes. The H 2 S adsorption products primarily manifest as elemental sulfur and sulfate within the pores of lignin carbon measuring less than 2 nm. Through thermal regeneration, the charcoal effectively eliminates the elemental sulfur adsorption product. Nevertheless, sulfate removal proved unsatisfactory, as the adsorption efficiency of KEC-700 following two thermal regenerations was approximately 41% of that observed for fresh samples.

materials science, multidisciplinary,engineering, chemical
Benign-by-design N-doped activated carbon from wasted aqueous assisted hydrochar of leftover rice for efficient H2S removal

Wei Hu,Jingchun Huang,Junwen Wang,Di Xie,Zhenqi Wang,Yu Qiao,Minghou Xu

DOI: https://doi.org/10.1016/j.fuel.2023.130233

IF: 7.4

2024-02-01

Fuel

Abstract:The N-doped activated carbon is a potential material for H2S removal, reusing N-rich waste aqueous as a nitrogen source is promising to prepare in-expensive N-doped activated carbon. In this study, N-rich waste aqueous assisted hydrothermal carbonization and KOH activation were used to prepare activated carbon from starchy waste, concentrating on the effects of the nitrogen species (inorganic-N and organic-N) on the physicochemical characteristics and desulfurization performance of carbon material. Introducing inorganic-N (i.e., NH3·H2O) can increase the defect degree and enhance the formation of micropores and mesopores for N-doped activated carbon, leading to high storage ability for desulfurization products and well oxidation performance. The organic-N (i.e., alanine) was conducive to forming pyridinic-N and quinonyl for N-doped activated carbon, resulting in a strong ability of adsorption, dissolution, and oxidation for H2S. The organic-N determined the high breakthrough sulfur capacity for hydrothermal aqueous doping activated carbon (110.7 mg/g), which was ∼ 4.08 times than undoped activated carbon. The primary product of the desulfurization process was elemental sulfur (74.08%), with sulfuric acid and sulfonic acid as the subsequent by-products. After nitrogen doping, the contents of elemental sulfur and sulfuric acid increased by 5.65 and 1.73 times, respectively. The results revealed the correlations between nitrogen species in hydrothermal aqueous and the desulfurization performance of activated carbon, which could guide the selection of nitrogen-rich aqueous for synthesizing H2S removal N-doped activated carbon via the above novel method.

energy & fuels,engineering, chemical
Comparing and combining gamma-hydroxybutyric acid (GHB) and naltrexone in maintaining abstinence from alcohol: An open randomised comparative study

F. Caputo,G. Addolorato,M. Stoppo,S. Francini,T. Vignoli,F. Lorenzini,A. D. Re,C. Comaschi,P. Andreone,F. Trevisani,M. Bernardi,Alcohol Treatment Study Group

DOI: https://doi.org/10.1016/j.euroneuro.2007.04.008

IF: 5.415

2007-12-01

European Neuropsychopharmacology

Abstract:
Development of microwave-assisted nitrogen-modified activated carbon for efficient biogas desulfurization: a practical approach

Norhusna Mohamad Nor,Lau Lee Chung,Abdul Rahman Mohamed

DOI: https://doi.org/10.1007/s11356-022-20627-x

IF: 5.8

2022-05-12

Environmental Science and Pollution Research

Abstract:Removal of H2S (hydrogen sulfide) from biogas is anticipated for higher energy conversion of methane (CH4), while reducing the detrimental impacts of corroding the metal parts in the plant and its hazardous effect on humans and the environment. The introduction of microwave (MW) heating and nitrogen-modification could generate superior adsorbent features, contributing to high H2S removal. Up to date, there is no work reported on the influence of physicochemical characteristics of nitrogen-modified carbon synthesized via MW and conventional heating (TH) methods and their performance in H2S removal. Palm shell activated carbon (PSAC) was functionalized with nitrogen groups via urea impregnation, followed by the synthesis of MW and TH at 950 °C, 500 ml/min of N2 flow rate and 30 min of heating time. MW and TH heating effects on the modified PSAC adsorbent were analysed and compared towards hydrogen sulfide (H2S) removal. PSAC with nitrogen functionalization produced using MW heating (PSAC-MW) demonstrates superior performance, with an adsorption capacity of 356.94 mg/g. The adsorbent sample generated using MW heating exhibited notable properties, including a large surface area and a sponge-like structure, with new pores developed within the current pores. Instead of that, there was an observation of ‘hot spot’ appearance during the MW heating process, which is believed to be responsible for the development of physical and chemical characteristics of the adsorbent. Thus, it is believed that MW heating was assisted in the development of the adsorbent’s properties and at the same time contributed to the high removal of H2S at low adsorption temperature. The utilization of biomass-based adsorbent (PSAC) for H2S removal can address the lignocellulosic waste disposal problem, while mitigating the H2S release from the biogas production plants thus has several environmental merits. This indirectly contributed to zero-waste generation, while overcoming the adverse effects of H2S.

environmental sciences

Social Goals and the Valuation of Natural Capital

Adsorptive Oxidation of Aqueous Sulfide Onto Zerovalent Cobalt and Magnetite-Supported Biochars: Insights into Synthesis and Mechanistic Performance

Carbon nanosheets composited with MgO/CaO prepared by one-step co-pyrolysis strategy for efficient H 2 S oxidation at room temperature

Adsorption Mechanism and Regeneration Performance of Calcined Zeolites for Hydrogen Sulfide and Its Application

Preparation of sludge-straw-based activated carbon and its adsorption of H2S

The Efficiency and Mechanism of Humidity in Alleviating CO2 Inhibition on H2S Adsorption to Straw Biochars

Bamboo Derived Activated Carbon As Highly Efficient Catalysts for the Oxidation and Adsorption of Hydrogen Sulfide at Room Temperature

Towards Highly Exposed Active Sites Via Edge-N-rich Carbon Nanosheet @ Porous Biochar for Efficient H2S Catalytic Oxidation

Self-supporting nano-porous carbon nanosheet with organized sp2-C network for unprecedented catalytic performance in room-temperature H2S oxidization

Carbon-Rich carbon nitride nanocatalysts for H2S selective oxidation

[Advances in Mechanism and Influencing Factors Affecting Hydrogen Sulfide Adsorption by Biochar].

Towards highly exposed active sites via Edge-N-rich carbon nanosheet @ porous biochar for efficient H 2 S catalytic oxidation

Cu Nanoparticles Inlaid Mesoporous Carbon Aerogels as a High Performance Desulfurizer.

Preparation and Characterization of Cu(NO3)2 Modified Activated Carbon Adsorbents and Influencing Factors of H2S Adsorption

A Sustainable Design of ZnO-based Adsorbent for Robust H2S Uptake and Secondary Utilization As Hydrogenation Catalyst

Polyethyleneimine-functionalized mesoporous carbon nanosheets as metal-free catalysts for the selective oxidation of H2S at room temperature

Preparation of nitrogen-doped activated carbon used for catalytic oxidation removal of H 2 S

Study on the adsorption performance and regeneration of lignin-derived graphitic carbon for H 2 S

Benign-by-design N-doped activated carbon from wasted aqueous assisted hydrochar of leftover rice for efficient H2S removal

Comparing and combining gamma-hydroxybutyric acid (GHB) and naltrexone in maintaining abstinence from alcohol: An open randomised comparative study

Development of microwave-assisted nitrogen-modified activated carbon for efficient biogas desulfurization: a practical approach