Attitudes towards vaccination among chiropractic and naturopathic students.

J. Busse,K. Wilson,James B. Campbell

DOI: https://doi.org/10.1016/j.vaccine.2008.07.020

IF: 4.169

2008-11-18

Vaccine

Abstract:

What problem does this paper attempt to address?

Feasibility of Wearable Haptic Biofeedback Training for Reducing the Knee Abduction Moment During Overground Walking

Bryndan W. Lindsey,Junkai Xu,David Chiasson,Peter Shull,Nelson Cortes

DOI: https://doi.org/10.1115/1.4048082

2021-01-01

Abstract:Gait modifications are effective in reducing the first peak knee abduction moment (PKAM), a surrogate for knee loading. Reliance on 3D motion capture currently restricts these modifications to the laboratory. Therefore, our purpose was to test the feasibility of a novel wearable biofeedback system to train (1) toe-in and trunk lean modifications and (2) combined toe-in and trunk lean modifications to reduce PKAM during overground walking outside of the laboratory. Twelve healthy participants practiced modifications in a university hallway directly after performing five normal walking trials. The wearable feedback system provided real-time haptic biofeedback during training trials to inform participants if they were within the prescribed modification range (7-12deg greater than baseline). Participants were instructed to move to the next modification only once they felt comfortable and could perform it with minimal errors. Following training, five trials of each modification were immediately performed in the gait laboratory without feedback. All participants successfully modified their foot progression and trunk angle using the wearable system. At post-test, PKAM decreased from baseline by 62%, 55%, and 28% during combined, trunk leanand toe-in gait, respectively. The wearable feedback system was effective to modify participants' foot and trunk angle by the prescribed amount, resulting in reduced PKAM during all modifications at post-test. Participants were also able to perform a combined modification, although it took longer to report feeling comfortable doing so. This study demonstrates that a wearable feedback system is feasible to modify kinematic parameters and train gait modifications outside the laboratory.
A Systematic Review of Diagnostic Accuracy and Clinical Applications of Wearable Movement Sensors for Knee Joint Rehabilitation

Robert Prill,Marina Walter,Aleksandra Królikowska,Roland Becker

DOI: https://doi.org/10.3390/s21248221

IF: 3.9

2021-12-09

Sensors

Abstract:In clinical practice, only a few reliable measurement instruments are available for monitoring knee joint rehabilitation. Advances to replace motion capturing with sensor data measurement have been made in the last years. Thus, a systematic review of the literature was performed, focusing on the implementation, diagnostic accuracy, and facilitators and barriers of integrating wearable sensor technology in clinical practices based on a Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement. For critical appraisal, the COSMIN Risk of Bias tool for reliability and measurement of error was used. PUBMED, Prospero, Cochrane database, and EMBASE were searched for eligible studies. Six studies reporting reliability aspects in using wearable sensor technology at any point after knee surgery in humans were included. All studies reported excellent results with high reliability coefficients, high limits of agreement, or a few detectable errors. They used different or partly inappropriate methods for estimating reliability or missed reporting essential information. Therefore, a moderate risk of bias must be considered. Further quality criterion studies in clinical settings are needed to synthesize the evidence for providing transparent recommendations for the clinical use of wearable movement sensors in knee joint rehabilitation.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Design and Implementation of a Wearable System Based on a Flexible Capacitive Sensor, Monitoring Knee Laxity

Karthika Sheeja Prakash,Erik Andersen,Vicky Chantal Einem,Sabari Kannan Muthalagu,Priyank Agarwal,Hermann Otto Mayr,Michael Seidenstuecker,Nikolaus Rosenstiel,Shad Roundy,Peter Woias,Laura Maria Comella

DOI: https://doi.org/10.1002/adsr.202300058

2023-06-02

Advanced Sensor Research

Abstract:The developed polydimethylsiloxane based capacitive strain gauge sensor which is flexible, and wearable can be used for the knee laxity diagnosis. These gauges detect the change in capacitance as it is subjected to stress, providing real‐time data on capacitance versus the angle of rotation of the knee. Their sensitivity at lower angular rotations and ergonomic feature marks the milestone for a reliable diagnosis tool that could potentially detect anterior cruciate ligament injuries and aids in rehabilitation. The anterior cruciate ligament (ACL) tear is one of the most common knee injuries causing instability to the knee joint. Current methods of diagnosis fail to meet the ergonomic, reliability, and reproducibility requirements. Thus, the wearable sensors are gaining momentum to overcome current challenges. This paper aims at proposing a wearable capacitive based sensor system that shows a good potential in substituting the currently used methods for the diagnosis of ACL rupture. The developed sensor system measures the internal tibial rotation of the knee. It is compact and lightweight. Being cable free, it can be worn as a patch, without impeding the freedom of movement of the physician. Moreover, it can be powered with a battery or wireless. Both methods make it compact, ergonomic, easy for the patient to wear and for the doctor to use. To analyze the suitability of the developed sensing system, data from a knee simulator setup and three healthy volunteers (2 Males and 1 Female) are compared and analyzed. In all the patients, above 15° for every 5° angle variation, a relative change of capacitance with respect to its initial value of 0.01 is observed. These results are comparable with the knee simulator's data with a max RMSE of 0.002. Below 15° the system is additionally able to measure a gender‐based difference of rotation due to the higher flexibility of ligaments in females. For them the sensitivity below and above 15° is comparable, for male the sensitivity below 15° is lower. The results show that the developed system has good potential in substituting the currently used method for the diagnosis of ACL rupture and paves the way toward the continuous observation in free movement of knee laxity.
Noninvasive and Reliable Quantification of Anteromedial Rotatory Knee Laxity: A Pilot Study on Healthy Individuals

Lukas Willinger,Armin Runer,Romed Vieider,Lukas N. Muench,Sebastian Siebenlist,Philipp W. Winkler

DOI: https://doi.org/10.1177/03635465241234263

IF: 4.8

2024-03-22

The American Journal of Sports Medicine

Abstract:The American Journal of Sports Medicine, Ahead of Print. Background:Anteromedial rotatory instability (AMRI) of the knee is a complex and severe condition caused by injury to the anterior cruciate ligament and/or the medial collateral ligament. Clinical studies dealing with AMRI are rare, and objective measurements are nonexistent.Purpose/Hypothesis:The objectives of this study were, first, to quantify anteromedial rotatory knee laxity in healthy individuals using a noninvasive image analysis software and, second, to assess intra- and interrater reliability and equivalence in measuring anteromedial knee translation (AMT). It was hypothesized that AMT could be reliably quantified using a noninvasive image analysis software.Study design:Cohort study; Level of evidence, 3.Methods:This prospective proof-of-concept study included healthy individuals aged 16 to 40 years with no history of knee injury or surgery. Three adhesive surface markers were placed on predefined landmarks on the medial side of the knee. Three independent investigators examined anteromedial rotatory knee laxity with an anterior drawer test in different tibial rotations (neutral tibial rotation, 15° of external tibial rotation, and 15° of internal tibial rotation). The entire examination of each knee was recorded, and AMT including the side-to-side difference (SSD) was assessed using a freely available and validated image analysis software (PIVOT iPad application). Group comparisons were performed using a 1-way analysis of variance with Bonferroni-adjusted post hoc analysis. Intraclass correlation coefficients (ICCs) were calculated to assess inter- and intrarater reliability of AMT measurements. Equivalence of measurements was evaluated using the 2 one-sided t-test procedure.Results:Anteromedial rotatory knee laxity was assessed in 30 knees of 15 participants (53% male) with a mean age of 26.2 ± 3.5 years. In all 3 raters, the highest AMT was observed in neutral tibial rotation (range of means, 2.2-3.0 mm), followed by external tibial rotation (range of means, 2.0-2.4 mm) and internal tibial rotation (range of means, 1.8-2.2 mm; P < .05). Intrarater reliability of AMT (ICC, 0.88-0.96) and SSD (ICC, 0.61-0.96) measurements was good to excellent and moderate to excellent, respectively. However, interrater reliability was poor to moderate for AMT (ICC, 0.44-0.73) and SSD (ICC, 0.12-0.69) measurements. Statistically significant equivalence of AMT and SSD measurements was observed between and within raters for almost all testing conditions.Conclusion:Anteromedial rotatory knee laxity could be quantified using a noninvasive image analysis software, with the highest AMT observed during neutral tibial rotation in uninjured individuals. Reliability and equivalence of measurements were good to excellent within raters and moderate between raters.

orthopedics,sport sciences
Hydroxy radical as autotoxin in chemotactically activated neutrophils.

Till Go,M. Lutz,P. Ward

Abstract:Chemotactic stimulation of neutrophils can result in the production and release of toxic oxygen metabolites which, in turn, may affect neutrophil function. We have investigated the effects of catalase, superoxide dismutase, hydroxyl radical scavengers and a iron chelator on chemotactic responses of rat peritoneal neutrophils in vitro. Neutrophils were quantitatively assessed in micropore filters for chemotactic migration to several different chemotactic peptides including C5a, present in inulin-activated rat serum, the non-oxidizable tripeptide N-formyl-norleucyl-leucyl-phenylalanine, and the oxidizable peptide N-formyl-methionyl-leucyl-phenylalanine. The presence of catalase in the suspension of neutrophils caused a dose-dependent enhancement of chemotactic responses to each of the three chemotactic stimuli, whereas addition of superoxide dismutase had little effect. Hydroxyl radical scavengers (mannitol, dimethyl sulfoxide) or the iron chelator, deferoxamine, also afforded significant, dose-dependent enhancement of neutrophyl chemotaxis, while the iron-saturated chelator was devoid of chemotaxis-enhancing properties. Furthermore, stimulation of rat neutrophils with phorbol myristate acetate resulted in the appearance of products of lipid peroxidation (conjugated Schiff bases), the generation of which could be prevented by the hydroxyl radical scavenger, dimethyl thiourea. These data suggest that catalase, hydroxyl radical scavengers, and iron chelators protect chemotactically stimulated neutrophils from autotoxicity caused by neutrophil-derived hydrogen peroxide and its iron-catalyzed conversion product, hydroxyl radical.
Validity of wearable sensors for total knee arthroplasty (TKA) rehabilitation: A study in younger and older healthy participants

L Forsyth,A Ligeti,M Blyth,J V Clarke,P E Riches

DOI: https://doi.org/10.1016/j.knee.2024.10.006

Abstract:Background: With 100,000 total knee arthroplasty (TKA) procedures taking place in the United Kingdom annually, the demand on rehabilitation services is high. Most regimes are home-based. Without clinician-patient interaction, detection of rehabilitation concerns can be delayed, reducing the chance of successful early intervention. Wearable technologies, such as MotionSenseTM (Stryker, US), may offer a solution to this problem by remotely supporting post-operative TKA rehabilitation through the provision of personalised rehabilitation and tracking of home exercises, enabling healthcare professionals to continuously monitor rehabilitation progress remotely. Validation of such devices against a known kinematic model in activities of daily living is important for confident interpretation of resulting clinical data. The aim of this study therefore was to validate the accuracy of MotionSenseTM against a clinical motion capture standard. Methods: Twenty younger and 14 older healthy, able-bodied adults attended one testing session (Younger: 24 ± 4 years old; Older: 71 ± 5 years old). Movement was tracked using Vicon motion analysis and a Plug-In-Gait lower body model was applied to all participants. Three activities were performed - walking, stair ascent, stair descent. The knee flexion angle root mean square error (RMSE) between the technologies was determined. Results: For both groups the knee flexion RMSE remained below 3° for all activities. The combined RMSE for all adults was 2.4° for walking, 2.7° for stair ascent, and 2.6° for stair descent. The signed error increased during the swing phase of gait. Conclusion: MotionSenseTM was found to accurately estimate knee flexion angles during several common activities compared to Vicon motion capture.
Ethics, nursing, and health care in the age of "re-form".

W. Mohr

DOI: https://doi.org/10.1097/00006527-199601640-00012

1996-01-24

Abstract:
Accuracy of a Custom Physical Activity and Knee Angle Measurement Sensor System for Patients with Neuromuscular Disorders and Gait Abnormalities

Frank Feldhege,Anett Mau-Moeller,Tobias Lindner,Albert Hein,Andreas Markschies,Uwe Klaus Zettl,Rainer Bader,Uwe Zettl

DOI: https://doi.org/10.3390/s150510734

IF: 3.9

2015-05-06

Sensors

Abstract:Long-term assessment of ambulatory behavior and joint motion are valuable tools for the evaluation of therapy effectiveness in patients with neuromuscular disorders and gait abnormalities. Even though there are several tools available to quantify ambulatory behavior in a home environment, reliable measurement of joint motion is still limited to laboratory tests. The aim of this study was to develop and evaluate a novel inertial sensor system for ambulatory behavior and joint motion measurement in the everyday environment. An algorithm for behavior classification, step detection, and knee angle calculation was developed. The validation protocol consisted of simulated daily activities in a laboratory environment. The tests were performed with ten healthy subjects and eleven patients with multiple sclerosis. Activity classification showed comparable performance to commercially available activPAL sensors. Step detection with our sensor system was more accurate. The calculated flexion-extension angle of the knee joint showed a root mean square error of less than 5° compared with results obtained using an electro-mechanical goniometer. This new system combines ambulatory behavior assessment and knee angle measurement for long-term measurement periods in a home environment. The wearable sensor system demonstrated high validity for behavior classification and knee joint angle measurement in a laboratory setting.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Accuracy of Measuring Knee Flexion after TKA through Wearable IMU Sensors

Ricardo Antunes,Paul Jacob,Andrew Meyer,Michael A. Conditt,Martin W. Roche,Matthias A. Verstraete

DOI: https://doi.org/10.3390/jfmk6030060

2021-07-05

Journal of Functional Morphology and Kinesiology

Abstract:Wearable sensors have the potential to facilitate remote monitoring for patients recovering from knee replacement surgery. Using IMU sensors attached to the patients’ leg, knee flexion can be monitored while the patients are recovering in their home environment. Ideally, these flexion angle measurements will have an accuracy and repeatability at least on par with current clinical standards. To validate the clinical accuracy of a two-sensor IMU system, knee flexion angles were measured in eight subjects post-TKA and compared with other in-clinic angle measurement techniques. These sensors are aligned to the patients’ anatomy by taking a pose resting their operated leg on a box; an initial goniometer measurement defines the patients’ knee flexion while taking that pose. The repeatability and accuracy of the system was subsequently evaluated by comparing knee flexion angles against goniometer readings and markerless optical motion capture data. The alignment pose was repeatable with a mean absolute error of 1.6 degrees. The sensor accuracy through the range of motion had a mean absolute error of 2.6 degrees. In conclusion, the presented sensor system facilitates a repeatable and accurate measurement of the knee flexion, holding the potential for effective remote monitoring of patients recovering from knee replacement surgery.
Rehabilitation and Return to Sport Assessment after Anterior Cruciate Ligament Injury: Quantifying Joint Kinematics during Complex High-Speed Tasks through Wearable Sensors

Stefano Di Paolo,Nicola Francesco Lopomo,Francesco Della Villa,Gabriele Paolini,Giulio Figari,Laura Bragonzoni,Alberto Grassi,Stefano Zaffagnini

DOI: https://doi.org/10.3390/s21072331

IF: 3.9

2021-03-26

Sensors

Abstract:The aim of the present study was to quantify joint kinematics through a wearable sensor system in multidirectional high-speed complex movements used in a protocol for rehabilitation and return to sport assessment after Anterior Cruciate Ligament (ACL) injury, and to validate it against a gold standard optoelectronic marker-based system. Thirty-four healthy athletes were evaluated through a full-body wearable sensor (MTw Awinda, Xsens) and a marker-based optoelectronic (Vicon Nexus, Vicon) system during the execution of three tasks: drop jump, forward sprint, and 90° change of direction. Clinically relevant joint angles of lower limbs and trunk were compared through Pearson’s correlation coefficient (r), and the Coefficient of Multiple Correlation (CMC). An excellent agreement (r > 0.94, CMC > 0.96) was found for knee and hip sagittal plane kinematics in all the movements. A fair-to-excellent agreement was found for frontal (r 0.55–0.96, CMC 0.63–0.96) and transverse (r 0.45–0.84, CMC 0.59–0.90) plane kinematics. Movement complexity slightly affected the agreement between the systems. The system based on wearable sensors showed fair-to-excellent concurrent validity in the evaluation of the specific joint parameters commonly used in rehabilitation and return to sport assessment after ACL injury for complex movements. The ACL professionals could benefit from full-body wearable technology in the on-field rehabilitation of athletes.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Wearable Loop Sensor for Bilateral Knee Flexion Monitoring

Yingzhe Zhang,Jaclyn B. Caccese,Asimina Kiourti

DOI: https://doi.org/10.3390/s24051549

IF: 3.9

2024-02-29

Sensors

Abstract:We have previously reported wearable loop sensors that can accurately monitor knee flexion with unique merits over the state of the art. However, validation to date has been limited to single-leg configurations, discrete flexion angles, and in vitro (phantom-based) experiments. In this work, we take a major step forward to explore the bilateral monitoring of knee flexion angles, in a continuous manner, in vivo. The manuscript provides the theoretical framework of bilateral sensor operation and reports a detailed error analysis that has not been previously reported for wearable loop sensors. This includes the flatness of calibration curves that limits resolution at small angles (such as during walking) as well as the presence of motional electromotive force (EMF) noise at high angular velocities (such as during running). A novel fabrication method for flexible and mechanically robust loops is also introduced. Electromagnetic simulations and phantom-based experimental studies optimize the setup and evaluate feasibility. Proof-of-concept in vivo validation is then conducted for a human subject performing three activities (walking, brisk walking, and running), each lasting 30 s and repeated three times. The results demonstrate a promising root mean square error (RMSE) of less than 3° in most cases.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Dynamic CT scanning of the knee: Combining weight bearing with real-time motion acquisition

Luca Buzzatti,Benyameen Keelson,Joris Willem van der Voort,Lorenzo Segato,Thierry Scheerlinck,Savanah Héréus,Gert Van Gompel,Jef Vandemeulebroucke,Johan De Mey,Nico Buls,Erik Cattrysse,Ben Serrien

DOI: https://doi.org/10.1016/j.knee.2023.07.014

Abstract:Background: Imaging the lower limb during weight-bearing conditions is essential to acquire advanced functional joint information. The horizontal bed position of CT systems however hinders this process. The purpose of this study was to validate and test a device to simulate realistic knee weight-bearing motion in a horizontal position during dynamic CT acquisition and process the acquired images. Methods: "Orthostatic squats" was compared to "Horizontal squats" on a device with loads between 35% and 55% of the body weight (%BW) in 20 healthy volunteers. Intraclass Correlation Coefficient (ICC), and standard error of measurement (SEM), were computed as measures of the reliability of curve kinematic and surface EMG (sEMG) data. Afterwards, the device was tested during dynamic CT acquisitions on three healthy volunteers and three patients with patellofemoral pain syndrome. The respective images were processed to extract Tibial-Tuberosity Trochlear-Groove distance, Bisect Offset and Lateral Patellar Tilt metrics. Results: For sEMG, the highest average ICCs (SEM) of 0.80 (6.9), was found for the load corresponding to 42%BW. Kinematic analysis showed ICCs were the highest for loads of 42%BW during the eccentric phase (0.79-0.87) and from maximum flexion back to 20° (0.76). The device proved to be safe and reliable during the acquisition of dynamic CT images and the three metrics were computed, showing preliminary differences between healthy and pathological participants. Conclusions: This device could simulate orthostatic squats in a horizontal position with good reliability. It also successfully provided dynamic CT scan images and kinematic parameters of healthy and pathological knees during weight-bearing movement.
Measuring lumbar back motion during functional activities using a portable strain gauge sensor-based system: A comparative evaluation and reliability study

Magdalena Suter,Patric Eichelberger,Jana Frangi,Edwige Simonet,Heiner Baur,Stefan Schmid

DOI: https://doi.org/10.1016/j.jbiomech.2019.109593

IF: 2.4

2020-02-01

Journal of Biomechanics

Abstract:<p>Quantifying lumbar back motion during functional activities in real-life environments may contribute to a better understanding of common pathologies such as spinal disorders. The current study therefore aimed at the comparative evaluation of the Epionics SPINE system, a portable device for measuring sagittal lumbar back motion during functional activities. Twenty healthy participants were therefore evaluated with the Epionics SPINE and a Vicon motion capture system in two identical separate research visits. They performed the following activities: standing, sitting, chair rising, box lifting, walking, running and a counter movement jump (CMJ). Lumbar lordosis angles were extracted as continuous values as well as average and range of motion (ROM) parameters. Agreement between the systems was evaluated using Bland-Altman analyses, whereas within- and between-session reliability were assessed using intraclass correlation coefficients (ICC) and minimal detectable changes (MDC). The analysis showed excellent agreement between the systems for chair rising, box lifting and CMJ with a systematic underestimation of lumbar lordosis angles during walking and running. Reliability was moderate to high for all continuous and discrete parameters (ICC≥0.62), except for ROM during running (ICC=0.29). MDC values were generally below 15°, except for CMJ (peak values up to 20° within and 25° between the sessions). The Epionics SPINE system performed similarly to a Vicon motion capture system for measuring lumbar lordosis angles during functional activities and showed high consistency within and between measurement sessions. These findings can serve researchers and clinicians as a bench mark for future investigations using the system in populations with spinal pathologies.</p>

engineering, biomedical,biophysics
Inertial Sensor-Based Lower Limb Joint Kinematics: A Methodological Systematic Review

Ive Weygers,Manon Kok,Marco Konings,Hans Hallez,Henri De Vroey,Kurt Claeys

DOI: https://doi.org/10.3390/s20030673

IF: 3.9

2020-01-26

Sensors

Abstract:The use of inertial measurement units (IMUs) has gained popularity for the estimation of lower limb kinematics. However, implementations in clinical practice are still lacking. The aim of this review is twofold—to evaluate the methodological requirements for IMU-based joint kinematic estimation to be applicable in a clinical setting, and to suggest future research directions. Studies within the PubMed, Web Of Science and EMBASE databases were screened for eligibility, based on the following inclusion criteria: (1) studies must include a methodological description of how kinematic variables were obtained for the lower limb, (2) kinematic data must have been acquired by means of IMUs, (3) studies must have validated the implemented method against a golden standard reference system. Information on study characteristics, signal processing characteristics and study results was assessed and discussed. This review shows that methods for lower limb joint kinematics are inherently application dependent. Sensor restrictions are generally compensated with biomechanically inspired assumptions and prior information. Awareness of the possible adaptations in the IMU-based kinematic estimates by incorporating such prior information and assumptions is necessary, before drawing clinical decisions. Future research should focus on alternative validation methods, subject-specific IMU-based biomechanical joint models and disturbed movement patterns in real-world settings.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Biomechanical and Physiological Variables in Dynamic and Functional Balance Control during Single-Leg Loading in Individuals with Chronic Ankle Instability: A Scoping Review

Chairat Phuaklikhit,Thanwarat Junsri,Seiji Saito,Satoshi Muraki,Ping Yeap Loh

DOI: https://doi.org/10.3390/sports12080224

2024-08-16

Abstract:Background: This scoping review summarizes the tasks and outcomes in dynamic and functional balance assessments of individuals with chronic ankle instability, focusing on the physiological and biomechanical characteristics. Method: A comprehensive literature search was conducted in PubMed, Scopus, Web of Science, and MEDLINE databases in September 2023 and revised in April 2024. Studies evaluating dynamic and functional balance in chronic ankle instability using clinical tests, as well as biomechanical and physiological outcomes, were included. Results: Out of 536 publications, 31 met the screening criteria. A history of ankle sprain was the main focus of the inclusion criteria (28 articles, 90%). The star excursion balance test, emphasizing maximum reach distance, was the most common quantitative task (12 articles, 66%). Physiological data mainly came from electromyography studies (7 articles, 23%), while biomechanical variables were often assessed through center of pressure studies using force plates (17 articles, 55%). Conclusions: The preferred quantitative clinical assessment was the star excursion balance test, focusing on normalized reach outcomes. Qualitative functional balance assessments emphasize landing activities and center of pressure displacement. Electromyography is commonly used to analyze the tibialis anterior and peroneus longus muscles. However, there is a lack of qualitative data on dynamic balance control, including morphological characteristics and the center of mass adaptation.
The Use of Wearable Sensors and Machine Learning Methods to Estimate Biomechanical Characteristics During Standing Posture or Locomotion: A Systematic Review

Isabelle J. Museck,Daniel L. Brinton,Jesse C. Dean

DOI: https://doi.org/10.3390/s24227280

IF: 3.9

2024-11-21

Sensors

Abstract:Balance deficits are present in a variety of clinical populations and can negatively impact quality of life. The integration of wearable sensors and machine learning technology (ML) provides unique opportunities to quantify biomechanical characteristics related to balance outside of a laboratory setting. This article provides a general overview of recent developments in using wearable sensors and ML to estimate or predict biomechanical characteristics such as center of pressure (CoP) and center of mass (CoM) motion. This systematic review was conducted according to PRISMA guidelines. Databases including Scopus, PubMed, CINHAL, Trip PRO, Cochrane, and Otseeker databases were searched for publications on the use of wearable sensors combined with ML to predict biomechanical characteristics. Fourteen publications met the inclusion criteria and were included in this review. From each publication, information on study characteristics, testing conditions, ML models applied, estimated biomechanical characteristics, and sensor positions were extracted. Additionally, the study type, level of evidence, and Downs and Black scale score were reported to evaluate methodological quality and bias. Most studies tested subjects during walking and utilized some type of neural network (NN) ML model to estimate biomechanical characteristics. Many of the studies focused on minimizing the necessary number of sensors and placed them on areas near or below the waist. Nearly all studies reporting RMSE and correlation coefficients had values 0.85, respectively, indicating strong ML model estimation accuracy. Overall, this review can help guide the future development of ML algorithms and wearable sensor technologies to estimate postural mechanics.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Validity and reliability of wearable inertial sensors in healthy adult walking: a systematic review and meta-analysis

Dylan Kobsar,Jesse M. Charlton,Calvin T.F. Tse,Jean-Francois Esculier,Angelo Graffos,Natasha M. Krowchuk,Daniel Thatcher,Michael A. Hunt

DOI: https://doi.org/10.1186/s12984-020-00685-3

2020-05-11

Journal of NeuroEngineering and Rehabilitation

Abstract:Abstract Background Inertial measurement units (IMUs) offer the ability to measure walking gait through a variety of biomechanical outcomes (e.g., spatiotemporal, kinematics, other). Although many studies have assessed their validity and reliability, there remains no quantitive summary of this vast body of literature. Therefore, we aimed to conduct a systematic review and meta-analysis to determine the i) concurrent validity and ii) test-retest reliability of IMUs for measuring biomechanical gait outcomes during level walking in healthy adults. Methods Five electronic databases were searched for journal articles assessing the validity or reliability of IMUs during healthy adult walking. Two reviewers screened titles, abstracts, and full texts for studies to be included, before two reviewers examined the methodological quality of all included studies. When sufficient data were present for a given biomechanical outcome, data were meta-analyzed on Pearson correlation coefficients (r) or intraclass correlation coefficients (ICC) for validity and reliability, respectively. Alternatively, qualitative summaries of outcomes were conducted on those that could not be meta-analyzed. Results A total of 82 articles, assessing the validity or reliability of over 100 outcomes, were included in this review. Seventeen biomechanical outcomes, primarily spatiotemporal parameters, were meta-analyzed. The validity and reliability of step and stride times were found to be excellent. Similarly, the validity and reliability of step and stride length, as well as swing and stance time, were found to be good to excellent. Alternatively, spatiotemporal parameter variability and symmetry displayed poor to moderate validity and reliability. IMUs were also found to display moderate reliability for the assessment of local dynamic stability during walking. The remaining biomechanical outcomes were qualitatively summarized to provide a variety of recommendations for future IMU research. Conclusions The findings of this review demonstrate the excellent validity and reliability of IMUs for mean spatiotemporal parameters during walking, but caution the use of spatiotemporal variability and symmetry metrics without strict protocol. Further, this work tentatively supports the use of IMUs for joint angle measurement and other biomechanical outcomes such as stability, regularity, and segmental accelerations. Unfortunately, the strength of these recommendations are limited based on the lack of high-quality studies for each outcome, with underpowered and/or unjustified sample sizes (sample size median 12; range: 2–95) being the primary limitation.

engineering, biomedical,rehabilitation,neurosciences
The use of wearable devices for walking and running gait analysis outside of the lab: A systematic review

Eva Bošnjak,Reed Ferber,Lauren C. Benson,Christian A. Clermont

DOI: https://doi.org/10.1016/j.gaitpost.2018.04.047

2018-06-01

Abstract:BACKGROUND: Quantitative gait analysis is essential for evaluating walking and running patterns for markers of pathology, injury, or other gait characteristics. It is expected that the portability, affordability, and applicability of wearable devices to many different populations will have contributed advancements in understanding the real-world gait patterns of walkers and runners. Therefore, the purpose of this systematic review was to identify how wearable devices are being used for gait analysis in out-of-lab settings.METHODS: A systematic search was conducted in the following scientific databases: PubMed, Medline, CINAHL, EMBASE, and SportDiscus. Each of the included articles was assessed using a custom quality assessment. Information was extracted from each included article regarding the participants, protocol, sensor(s), and analysis.RESULTS: A total of 61 articles were reviewed: 47 involved gait analysis during walking, 13 involved gait analysis during running, and one involved both walking and running. Most studies performed adequately on measures of reporting, and external and internal validity, but did not provide a sufficient description of power. Small, unobtrusive wearable devices have been used in retrospective studies, producing unique measures of gait quality. Walking, but not running, studies have begun to use wearable devices for gait analysis among large numbers of participants in their natural environment.CONCLUSIONS: Despite the advantages provided by the portability and accessibility of wearable devices, more studies monitoring gait over long periods of time, among large numbers of participants, and in natural walking and running environments are needed to analyze real-world gait patterns, and would facilitate prospective, subject-specific, and subgroup investigations. The development of wearables-specific metrics for gait analysis provide insights regarding the quality of gait that cannot be determined using traditional components of in-lab gait analyses. However, guidelines for the usability of wearable devices and the validity of wearables-based measurements of gait quality need to be established.

neurosciences,orthopedics,sport sciences
Defective gap junctional intercellular communication in lung cancer: loss of an important mediator of tissue homeostasis and phenotypic regulation.

R. Ruch,S. Porter,L. Koffler,L. Dwyer-Nield,A. Malkinson

DOI: https://doi.org/10.1080/019021401300053984

2001-04-01

Experimental Lung Research

Abstract:Gap junctions provide direct pathways for the exchange of molecules and ions between neighboring cells, a process known as gap junctional intercellular communication (GJIC). This GJIC is important for homeostasis and regulation of mitosis, differentiation, and apoptosis. Gap junctions are present in lung airway and alveolar epithelial cells and, in addition to the above roles, might coordinate ciliary beating and surfactant secretion. GJIC is decreased in human and mouse lung carcinoma cells because of reduced expression of the gap junction protein, connexin43 (Cx43), and defects in signal transduction pathways that mediate Cx43 function. This reduced GJIC is important in the behavior of lung carcinoma cells because forced expression of Cx43 in lung carcinoma cells inhibits their growth and tumorigenicity. In this report, we summarize our studies on the role of GJIC in lung neoplasia.
New record of Spotstripe snapper, Lutjanus ophuysenii (Perciformes: Lutjanidae) from Korea

Han-Na Kim,Jin-Koo Kim

DOI: https://doi.org/10.1186/S41240-016-0043-7

2016-12-12

Abstract:

Attitudes towards vaccination among chiropractic and naturopathic students.

Feasibility of Wearable Haptic Biofeedback Training for Reducing the Knee Abduction Moment During Overground Walking

A Systematic Review of Diagnostic Accuracy and Clinical Applications of Wearable Movement Sensors for Knee Joint Rehabilitation

Design and Implementation of a Wearable System Based on a Flexible Capacitive Sensor, Monitoring Knee Laxity

Noninvasive and Reliable Quantification of Anteromedial Rotatory Knee Laxity: A Pilot Study on Healthy Individuals

Hydroxy radical as autotoxin in chemotactically activated neutrophils.

Validity of wearable sensors for total knee arthroplasty (TKA) rehabilitation: A study in younger and older healthy participants

Ethics, nursing, and health care in the age of "re-form".

Accuracy of a Custom Physical Activity and Knee Angle Measurement Sensor System for Patients with Neuromuscular Disorders and Gait Abnormalities

Accuracy of Measuring Knee Flexion after TKA through Wearable IMU Sensors

Rehabilitation and Return to Sport Assessment after Anterior Cruciate Ligament Injury: Quantifying Joint Kinematics during Complex High-Speed Tasks through Wearable Sensors

Wearable Loop Sensor for Bilateral Knee Flexion Monitoring

Dynamic CT scanning of the knee: Combining weight bearing with real-time motion acquisition

Measuring lumbar back motion during functional activities using a portable strain gauge sensor-based system: A comparative evaluation and reliability study

Inertial Sensor-Based Lower Limb Joint Kinematics: A Methodological Systematic Review

Biomechanical and Physiological Variables in Dynamic and Functional Balance Control during Single-Leg Loading in Individuals with Chronic Ankle Instability: A Scoping Review

The Use of Wearable Sensors and Machine Learning Methods to Estimate Biomechanical Characteristics During Standing Posture or Locomotion: A Systematic Review

Validity and reliability of wearable inertial sensors in healthy adult walking: a systematic review and meta-analysis

The use of wearable devices for walking and running gait analysis outside of the lab: A systematic review

Defective gap junctional intercellular communication in lung cancer: loss of an important mediator of tissue homeostasis and phenotypic regulation.

New record of Spotstripe snapper, Lutjanus ophuysenii (Perciformes: Lutjanidae) from Korea