Abstract:Correct resection of the tibial bone in total ankle replacement (TAR) procedure is crucial for accurate TAR implant positioning and the avoidance of post-operative complications. However, the biomechanical influence of the resection depth of tibial bone for TAR is not clearly understood. Therefore, the objective of this study is to investigate the biomechanical characteristics of the distal tibia with different resection depths after primary TAR. Tibial bone models of eight healthy volunteers (age 27 ± 3.83 years old, 5 Males and 3 females) were constructed and 6 to 16 mm resection depths of each bone were performed under the guidance of senior foot and ankle surgeons. A 4 mm tibial plate was reversed engineering to completely cover the bone resection surface. And finite element analyses were performed to evaluate the biomechanical behavior of these models. 5.2 times of body weight was applied as a worst-case scenario loading condition and element-based material assignment was used for the tibial bone. The resection surface area, resection volume, von Mises stress, and strain at each resection surface were analyzed. As bone resection depth increased from 6 to 16 mm, the resection surface area decreased from 1125.25 $$\pm$$ 99.76 $${\text{m}\text{m}}^{2}$$ to 889.27 $$\pm$$ 101.08 $${\text{m}\text{m}}^{2}$$ , while the resection volume increased from 14701 $$\pm$$ 4376.30 $${\text{m}\text{m}}^{3}$$ to 25116 $$\pm$$ 3354.27 $${\text{m}\text{m}}^{3}$$ . The biomechanical simulation results showed average von Mises stress increased from 3.46 $$\pm$$ 1.06 MPa to 3.85 $$\pm$$ 0.43 MPa. The average strain increased with the resection depth, from 5.11 $$\pm$$ 1.577 microstrain to 5.68 $$\pm$$ 1.87 microstrain (reach the highest points at 8 to 10 mm resection depth), then decreased to 4.62 $$\pm$$ 1.26 microstrain. Both the stress and strain were mainly distributed peripherally. As the resection depth was increased in the tibia during TAR, the resection surface area decreased but the resection volume and stress at the surface increased. The strain at the resection surface increased first and then decreased which reached a plateau at 8 to 10 mm resection depth. The 8 to 10 mm above the tibial plafond may be the weakest region of bone support in the distal tibia, which should be avoided in the design tibial component for TAR.

Biomechanical study of effect of tibial posteromedial defect depth and area on primary TKA implant stability

Assessment of the primary stability of revision tibial trays augmented with a cementless sleeve in AORI Type III defects

Finite-element Analysis of the Proximal Tibial Sclerotic Bone and Different Alignment in Total Knee Arthroplasty

The optional depth of screw for the treatment of tibial plateau defect in total knee arthroplasty: A finite element analysis

Reconstruction of Severe Acetabular Bone Defect with 3D Printed Ti6Al4V Augment: A Finite Element Study

Biomechanical role of posterior cruciate ligament in total knee arthroplasty: A finite element analysis

Medial-lateral translational malalignment of the prosthesis on tibial stress distribution in total knee arthroplasty: A finite element analysis

The Effect of Patient-Related Factors on the Primary Fixation of PEEK and Titanium Tibial Components: A Population-Based FE Study

Primary stability of tibial plateaus under dynamic compression-shear loading in human tibiae - Influence of keel length, cementation area and tibial stem

Finite-element analysis of the influence of tibial implant fixation design of total ankle replacement on bone-implant interfacial biomechanical performance

Biomechanical evaluation of total ankle arthroplasty. Part II: Influence of loading and fixation design on tibial bone-implant interaction

A novel computational workflow to holistically assess total knee arthroplasty biomechanics identifies subject-specific effects of joint mechanics on implant fixation

Stability of Three‐Dimensional Printed Custom‐Made Metaphyseal Cone for Tibial Bone Defects Reconstruction: A Finite Element Analysis and Biomechanical Study

Finite Element Analysis of the Biomechanical Effect of Bone Resection Depth in the Distal Tibia after Total Ankle Replacement

Biomechanical Lower Limb Model to Predict Patellar Position Alteration after Medial Open Wedge High Tibial Osteotomy

Influence of the angle between tibial and prosthesis mechanical axes on tibial bone remodeling in total knee arthroplasty

Development of Digital Twins to Optimize Trauma Surgery and Postoperative Management. A Case Study Focusing on Tibial Plateau Fracture

Clinical and Computational Evaluation of an Anatomic Patellar Component

Repair Materials For Bone Defects Of The Tibial Plateau In Primary Total Knee Arthroplasty

Imaging in revision total knee arthroplasty: A novel 3D classification system for tibial bone defects

Biomechanical comparison between metal block and cement-screw techniques for the treatment of tibial bone defects in total knee arthroplasty based on finite element analysis