Abstract:The reservoir type of the MH oil field in the Junggar Basin is a typical low-permeability conglomerate reservoir. The MH oilfield was developed by water injection in the early stage. Nowadays, the reservoir damage is serious, and water injection is difficult. There is an urgent need to carry out conversion injection flooding research to improve oil recovery. The use of CO2 oil-flooding technology can effectively supplement formation energy, reduce greenhouse gas emissions, and improve economic benefits. In order to clarify the feasibility of CO2 flooding to improve oil recovery in conglomerate reservoirs with low permeability, strong water sensitivity, and severe heterogeneity, this paper researched the impact of CO2 miscibility on production characteristics and mechanisms through multi-scale experiments. The aim was to determine the feasibility of using CO2 flooding to enhance oil recovery. This study initially elucidated the oil displacement characteristics of varying degrees of miscibility in different dimensions using slim tube experiments and long core experiments. Subsequently, mechanistic research was conducted, focusing on the produced oil components, changes in interfacial tension, and conditions for pore mobilization. The results indicate that the minimum miscibility pressure (MMP) of the block is 24 MPa. Under the slim tube scale, the increase in the degree of miscibility can effectively delay the gas breakthrough time; under the core scale, once the pressure reaches the near mixing phase, the drive state can transition from a non-mixed "closed-seal" to a "mixed-phase" state. Compared to the immiscible phase, the near-miscible and completely miscible phase can improve the final recovery efficiency by 9.27% and 18.72%. The component differences in the displacement products are mainly concentrated in the high-yield stage and gas breakthrough stage. During the high-yield stage, an increase in miscibility leads to a higher proportion of heavy components in the produced material. Conversely, in the gas breakthrough stage, extraction increases as the level of mixing increases, demonstrating the distinct extracting characteristics of different degrees of mixed phases. The core experiences significant variations in oil saturation mostly during the pre-gas stage. CO2 miscible flooding can effectively utilize crude oil in tiny and medium-sized pores during the middle stage of flooding, hence reducing the minimum threshold for pore utilization to 0.3 μm.

Research on Component Variation and Factors Affecting Minimum Miscible Pressure in Low Viscosity Oil Miscibility Process

Experimental Study on Oil-Gas Interaction Mechanism during Offshore Heavy Oil Gas Injection

Insight into miscibility mechanism of multiple components crude oil in CO2/CH4 by molecular dynamic simulation

Study on Interaction Characteristics of Injected Natural Gas and Crude Oil in a High Saturation Pressure and Low-Permeability Reservoir

Research on Minimum Miscible Pressure Between Crude Oil and Supercritical Carbon Dioxide System in Ultra-Low Permeability Reservoir by the Long-Slim-Tube Experiment Method

Study on Mechanism and Features of Unstable-State Displacement of Miscible Hydrocarbon-Gas Flooding

The effect of gas injection velocity and pore morphology on displacement mechanisms in porous media based on CFD approach

Dynamics and miscible behaviors of hydrocarbon gas and crude oil in nanoslits: Effects of light gas type and crude oil components

Comprehensive Review of the Determination and Reduction of the Minimum Miscibility Pressure during CO 2 Flooding

The Influence of Slim Tube Length on the Minimum Miscibility Pressure of CO2 Gas–Crude Oil

MD-CFD simulation on the miscible displacement process of hydrocarbon gas flooding under deep reservoir conditions

Visualization of CO 2 -oil vanishing interface to determine minimum miscibility pressure using microfluidics

Characteristics and Mechanisms of CO2 Flooding with Varying Degrees of Miscibility in Reservoirs Composed of Low-Permeability Conglomerate Formations

Miscibility of light oil and flue gas under thermal action

Modification of interfacial tension by considering the effect of porous medium during near miscible gas injection

Study on the Variation of Crude Oil and Flue Gas Components in Flue-Gas-Assisted Steam Flooding

Investigating the vaporization mechanism's effect on interfacial tension during gas injection into an oil reservoir

Influence of Gas Injection Parameters on the Effect of Unstable-state Displacement by Gas Flooding

Improved fluid characterization and phase behavior approaches for gas flooding and application on Tahe light crude oil system

Chemical strategies for enhancing CO 2 -Hydrocarbon miscibility

Chemical-assisted minimum miscibility pressure reduction between oil and methane