Abstract:Aerodynamic cooling of hot components/surfaces such as those encountered in gas turbine engines is needed to avoid premature failure of parts due to thermo-mechanical stresses. An effective way of achieving this cooling is through the exchange of heat via effusion/film cooling holes on the hot surfaces. The gases absorb heat as they flow through the cooling holes and also by forming a protective layer of relatively cool gases near the hot surface. Modeling these processes allow for durable design of components and computational simulations offer a complementary way to design new parts or enable performance assessment of the existing parts at new operating conditions. However, in order to perform numerical simulations of heat transfer through effusion holes, the heat conduction through the solid liner and the convection from the gas phase must be coupled considering all the relevant length and time scales. The time scale separation between the solid and the gas phase makes this prohibitively expensive for large scale computations. In applications involving hundreds of effusion holes, resolving the geometry of each effusion hole along with the primary flow (with typically larger length scales) is very challenging. In the current work, we overcome the difficulties associated with the resolution of cooling holes by employing a local source method (Andreini et al, J. Eng. Gas Turb. Power, 2014) to model the heat transfer to the walls. This method is assessed in a canonical configuration based on experiments performed by Gustafsson (Gustaffson, Ph.D. Thesis, 2001).Large Eddy Simulations (LES) coupled with conjugate heat transfer (CHT) models are used in this study. Simulations that resolve the flow passages explicitly using mesh both in the fluid and the solid domains, were used to validate the fidelity of grid resolution, turbulence models and other simulation parameters in predicting velocity fields and wall temperature data. Although, resolving all the effusions passages provides the most accurate results, it is not practical in real applications. Hence, a local source model is employed to model the heat transfer that happens in the cooling-hole passages. In this method, the effusion passage is not resolved (using a mesh) and the mass transfer across the cooling hole passage is prescribed as an injection-extraction boundary condition. The heat transfer at the fluid-solid interface of the cooling-hole passage is also modeled based on Nusselt number correlations available in the literature. This modeling procedure enables simulations with flexible mesh topologies that can be generated at a relatively low cost in comparison to the fully resolved mesh configurations. The local source method is assessed and validated using the available experimental data. The results show that the meshes which resolve the penetration depth in the solid and which conform at the solid-gas interface provide better prediction of the wall temperatures.

Modeling of the influence of local heat sources on a light gas stratification formation and erosion in a large-scale experimental facility using eddy resolving numerical approach

Numerical Investigation of Swirl-Stabilized Pulverized Coal Flames in Air and Oxy-Fuel Atmospheres by Means of Large Eddy Simulation Coupled with Tabulated Chemistry

Numerical Analysis on Hydrogen Stratification and Post-Inerting of Hydrogen Risk

Simultaneous Approach for Simulation of A High-Temperature Gas-Cooled Reactor

Multi-physics modeling of the long-term evolution of helium plasma exposed surfaces

High-Fidelity Simulation of the Light-to-Dense Stratification Transient in the HiRJET Facility

Numerical Investigation on Erosion of Hydrogen Stratification by Steam Jet Within a Local Compartment

Large-scale PANDA facility – radiation experiments and CFD calculations

Data-driven Hi2Lo for Coarse-grid System Thermal Hydraulic Modeling

Toward Direct Numerical Simulation of Turbulent and Transitional Flow in Hexagonal Subchannels for Helium Conditions

CFD simulations of helium layer erosion in one PANDA vessel following cooler activation

A method for examining ensemble averaging forms during the transition to turbulence in HED systems for application to RANS models

ICONE23-1277 INVESTIGATION OF THE INFLUENCE OF TURBULENCE MODELS ON THE SIMULATION OF THE GAS DISTRIBUTION

Modeling Effusion Cooling And Conjugate Heat Transfer Using Local Source Method

The effect of turbulence modeling on hydrogen jet dispersion inside a compartment space using the HYDRAGON code

DEVELOPMENT OF A DATA-DRIVEN TURBULENCE MODEL FOR THERMAL STRATIFICATION ANALYSIS IN REACTOR SYSTEM

Experimental study on gas mixing and transport induced by external cooling on large-scale facility

Large Eddy Simulation of Turbulent Stratified Combustion Using Dynamic Thickened Flame Coupled with Tabulated Detailed Chemistry

Application Of Some Turbulence Models To Simulate Buoyancy-Driven Flow

Dimensional comparable numerical analysis of the thermal stratification in the lead-cooled experimental facility CLEAR-S

Large Eddy Simulation of Hydrogen/air Scramjet Combustion Using Tabulated Thermo-Chemistry Approach