Catalytic spectrophotometric determination of tungsten using the malachite green-Ti(III) redox reaction and a thiocyanate activator.

N. Pourreza,I. Mohammadi-Sedehi

DOI: https://doi.org/10.1016/S0039-9140(01)00566-5

2002-03-04

Abstract:

What problem does this paper attempt to address?

Preparation of WO<sub>x</sub>-TiO<sub>2</sub> and the Photocatalytic Activity under Visible Irradiation

Hai Yan Song,Hong Fu Jiang,Xing Qin Liu,Yin Zhu Jiang,Guang Yao Meng

DOI: https://doi.org/10.4028/www.scientific.net/KEM.336-338.1979

2007-01-01

Key Engineering Materials

Abstract:Nanocrystalline tungsten oxide doped titanium dioxide (WOx-TiO2) powders were prepared by TiCl4 hydrolysis and characterized by XRD, XPS, UV-Vis absorption spectra and TEM. Results showed that WO, not only hindered the growth of TiO2 particles but also greatly increased the transformation temperature (>800 degrees C) from anatase to rutile during sintering; the dominant fraction of tungsten oxides was non-stoichiometric tungsten oxide (WxOy) with Wn+ (4<n<6), which could easily substitute Ti4+ in the lattice of TiO2. The light absorption band of TiO2 changed from the near UV to the visible light range (2.68 eV in 1.0 %WOx-TiO2) because of the tungsten impurity energy level induced by WxTi1-xO2. The photocatalysis experiments demonstrated that the MB in aqueous solution was successfully degraded within 1h using WOx-TiO2 with an optimal WOx dosage of 1% under visible light irradiation.
Microstructure and performance of Z-scheme photocatalyst of silver phosphate modified by MWCNTs and Cr-doped SrTiO3 for malachite green degradation

Yan Lin,Shaohua Wu,Xiang Li,Xin Wu,Chunping Yang,Guangming Zeng,Yanrong Peng,Qi Zhou,Li Lu

DOI: https://doi.org/10.1016/j.apcatb.2018.01.054

2018-01-01

Abstract:•A novel Z-scheme heterojunction photocatalyst Ag3PO4@MWCNTs@Cr:SrTiO3 was successfully synthesized.•The significant changes of crystal size and micro-morphology for Ag3PO4 were firstly observed due to the addition of MWCNTs.•The composite photocatalysts exhibited superior photocatalytic activities and great stability under both sunlight and visible light irradiation.•A pathway for photocatalytic degradation of malachite green (MG) was proposed.
Extraction System for the Spectrophotometric Determination of Tungsten(VI) with 4-Nitrocatechol and Benzalkonium Chloride

Vidka Vassileva Divarova,Kirila Trifonova Stojnova,Ivelina Dobromirova Radkovska,Antoaneta Dimitrova Saravanska,Galya Kostadinova Toncheva,Vassil Borisov Delchev,Kiril Blazhev Gavazov

DOI: https://doi.org/10.17344/acsi.2024.8835

2024-09-10

Abstract:A novel chromogenic system for the liquid-liquid extraction and determination of trace amounts of tungsten(VI) was investigated. The system comprises 4-nitrocatechol (4NC) as a chromogenic reagent, sulfuric acid as a complexing medium, and benzalkonium chloride (BAC) as a source of bulky cations (BA+), which readily form chloroform-extractable ion-association complexes. The impact of foreign ions and reagents was studied, and the optimal conditions for the sensitive, selective, and inexpensive determination of tungsten(VI) were identified. The limit of detection, linear working range, and molar absorptivity at lmax (422 nm) were determined to be 31 ng cm-3, 0.1-4.4 µg cm-3, and 5.49 × 104 dm3 mol-1 cm-1, respectively. The composition of the extracted complex was 1:2:2 (W:4NC:BA). Two potential structures of its anionic component, [WO2(4NC)2]2-, were discussed based on optimizations at the B3LYP/CEP-4G theoretical level and comparison between theoretical and experimental spectra.
Quantification of tungsten in real samples spectrophotometrically using optical sensor

Salah M. El-Bahy,Refat El-Sayed,Khaled F. Debbabi,Alaa S. Amin,Naglaa Mohamed

DOI: https://doi.org/10.1016/j.molliq.2024.126104

IF: 6

2024-09-28

Journal of Molecular Liquids

Abstract:A new methodology was devised to detect tungsten in aqueous samples, employing a sensor membrane crafted by physically incorporating a tungsten-selective compound, 5-(2 -bromophenylazo)-6-hydroxypyrimidine-2,4-dione (BPAHPD), into a plasticized poly(vinyl chloride). The addition of Triton X-114 was observed to be advantageous in augmenting the absorption of HWO 4 − ions from the liquid phase into the membrane phase, thereby amplifying sensor absorption intensity. The method established a linear dynamic span of 15–350 ng mL −1 for W(VI), exhibiting a notable correlation coefficient of 0.9992. Quantification and detection limits were determined to be 14.85 and 4.45 ng mL −1 , correspondingly, under optimized conditions. The Sandell responsiveness and molar absorptivity were calculated at 0.0455 ng cm −2 and 4.04 × 10 8 L/mol cm −1 , respectively. The sensor demonstrated superb selectivity, as demonstrated by the negligible influence of potential interfering species. Statistical analyses, encompassing variance ratio F-tests and Student's t-tests, indicated no substantial differences. The efficacy of the methodology was authenticated through the scrutiny of genuine samples, with statistical comparison to the ICP-AES method.

chemistry, physical,physics, atomic, molecular & chemical
Spectrophotometric Determination of Chromium in Waste Water and Soil.

WB QI,LZ ZHU

DOI: https://doi.org/10.1016/0039-9140(86)80161-8

IF: 6.1

1986-01-01

Talanta

Abstract:The reaction of Cr(VI) with o-nitrophenylfluorone (NPF) in presence of cetyltrimethyl-ammonium bromide (CTMAB) to form a purplish red complex at pH 4.7-6.6 by heating at 50 degrees for 10 min has been investigated. The composition of the complex is 1:2:2 [Cr(VI):NPF:CTMAB], the wavelength of maximum absorbance is 582 nm. The molar absorptivity is 1.11 x 10(5)1.mole(-1).cm(-1). Beer's law is obeyed up to 0.2 microg ml Cr(VI) concentration. The interference of several ions, including Cu(2+), Fe(3+) and Al(3+), is eliminated by addition of a masking mixture containing KF, DCTA and tartrate. A new sensitive method for determination of chromium in waste water and soil is presented.
A Novel Visible Light-Driven TiO2 Photocatalytic Reduction for Hexavalent Chromium Wastewater and Mechanism

Baoxiu Zhao,Kaixin Zhang,Yue Huang,Qi Wang,Hao Xu,Yilin Wang,Jincheng Li,Tianwen Song,Wenxiang Xia,Jie Liu

DOI: https://doi.org/10.2166/wst.2021.116

IF: 2.43

2021-01-01

Water Science & Technology

Abstract:TiO2 photocatalyst was prepared with a sol-gel method and its characterizations were analyzed, then TiO2 photocatalytic reduction for Cr6+ was investigated in visible light irradiation and reduction mechanism were deduced lastly. Prepared TiO2 is anatase and bandgap is about 2.95 eV. Experimental results display that almost 100% Cr6+ is removed by visible-light-driven TiO2 photocatalytic reduction after 120 min when Cr2O72- initial concentration is 1.0 mg.L-1, TiO2 dosage is 1.0 g.L-1 and pH value is 3. In acidic aqueous solution, HCrO4- is the dominant existing form of Cr6+ and adsorbed by TiO2, forming a complex catalyst HCrO4-/TiO2 which wavelength enlarges to visible light zone, proved by UV-Vis DRS. Based on XPS data, it can be deduced that Cr6+ is adsorbed on the surface of TiO2 and then reduced to Cr(3+)in situ by photoelectrons. Self-assembly of HCrO4-/TiO2 complex catalyst and self-reduction of Cr(6+)in situ are the key steps to start visible-light-driven TiO2 photocatalytic reduction. Furthermore, TiO2 photocatalytic reduction for Cr6+ fits well with pseudo first-order kinetics and has potential application to treat chemical industrial wastewater.
A MWCNTs@CuAl2O4@SiO2 Nanocomposite for the Speciation of Cr(III), Cr(VI), and Total Chromium Prior to High-Resolution Continuum Source Flame Atomic Absorption Spectrometric Determination

Hassan Elzain Hassan Ahmed,Mustafa Soylak

DOI: https://doi.org/10.1007/s11270-024-07020-9

2024-03-17

Water Air & Soil Pollution

Abstract:A solid-phase microextraction (SPME) method had been applied to speciate chromium in natural and wastewater samples. MWCNTs@CuAl 2 O 4 @SiO 2 nanocomposite was synthesized by sol–gel and calcination methods and then characterized using SEM, FTIR, and XRD techniques. MWCNTs@CuAl 2 O 4 @SiO 2 was used to extract Cr(VI) as pyrrolidine dithiocarbamate chelates. Some analytical parameters involving pH, ligand (APDC) and adsorbent amounts, sample initial and final volume, and the effects of matrices were tested and optimized. For the oxidation of Cr(III) to Cr(VI), potassium permanganate was used, and after that, the presented method was applied to determine the total chromium levels. The calculations were carried out to obtain Cr(III) concentration by finding differences between total chromium and Cr(VI) concentrations. The limit of detection (LOD) and limit of quantification (LOQ) were found to be 6.2 μg L −1 and 20.8 μg L −1 , respectively. The proposed method was successfully applied for chromium speciation in wastewater samples.

environmental sciences,water resources,meteorology & atmospheric sciences
Chromogenic reaction for tungsten (VI)-4-(6-bromo-2-benzothiazolylazo )pyrocatechol -emulsifier OP micellar complex and its application

Cheng Yao,Zhenpu Wang,Guosong Chen,Xueyin Gu

1996-01-01

Abstract:In the presence of OP, a non-ionic surfactant, W ( VI ) sensitively reacts with 4-(6-bromo-2-benzothiazolylazo) pyrocatechol (6-Br-BTAPC), a new chromogenic reagent, to form a stable, negatively charged, violet-red, ternary micellar complex in the pH range of 4. 0 to 5. 2. The ratio between W ( VI ) and 6-Br-BTAPC in the complex is 1 : 2 with ��max 558 nm, contrast (��) 118 nm, apparent stability constant 3. 7��109 and apparent ��558 7. 34X104 L �� mol-1 �� cm-1 in 20��C and pH 5. 0. Beer's law is obeyed in the range of 0 to 1. 4 mg/L of W ( VI ). The effect of many coexisting ions on the chromogenic reaction was studied. The chromogenic reaction not only has high sensitivity, but also higher selectivity. The structure of the complex was suggested. Satisfactory results have been achieved in applying this analytical method to the determination of trace or minor tungsten in alloy steel.
Novel Spectrophotometric Method for the Determination of Molybdenum in a PVA Medium

Di Junwei,Wu Ying,Tu Yifeng,Bi Shuping

DOI: https://doi.org/10.2116/analsci.18.125

IF: 1.967

2002-01-01

Analytical Sciences

Abstract:A novel spectrophotometric method for the determination of trace molybdenum in the presence of a large amount of tungsten was developed. This proposed method was based on the formation of a green charge-transfer polyoxometalate, molybdo-11-tungstophosphate-3,3',5,5'-tetramethylbenzidine- N -propanesulfonic, which was solubilized and stabilized in a PVA medium; the wavelength of the maximum absorption was at 660 nm. Beer’s law was obeyed in the Mo concentration range of 0.04–1.6 μg ml -1 . The molar absorptivity was 1.35 × 10 4 l mol –1 cm –1 . The developed method avoided the interference of W VI , and was conveniently applied to analyses of some tungsten ores containing Mo VI with satisfactory results.
Synthesis of Tungsten-Modified Sn3O4 through the Cetyltrimethylammonium Bromide-Assisted Solvothermal Method for Dye Decolorization under Visible Light Irradiation

Mai Furukawa,Daichi Iwamoto,Koki Inamori,Ikki Tateishi,Hideyuki Katsumata,Satoshi Kaneco

DOI: https://doi.org/10.3390/catal13081179

IF: 3.9

2023-08-03

Catalysts

Abstract:Novel tungsten-modified mixed-valence tin oxides (Sn3O4) with two oxidation numbers, such as Sn2+ and Sn4+, were successfully prepared by the cetyltrimethylammonium bromide (CTAB)-assisted solvothermal method in one-step using tin (II) chloride dihydrate and sodium tungstate (IV) dihydrate as the precursors for dye degradation of methyl orange (MO) under visible light irradiation. The synthesized materials were characterized by various techniques to investigate the surface/structural morphology and the optical property. The presence of tungsten and the optimized amount of CTAB in the preparation method were favorable for the photocatalytic dye degradation reaction. In particular, when 0.03 of CTAB was added to W-modified Sn3O4 (W-Sn3O4@CTAB) and its concentration was 0.6 mg/mL, 10 mg/L of MO could be decolorized almost completely in 40 min, with the apparent reaction rate constant of 0.0496 min−1. The improvement of photocatalytic activity for this proposed W-Sn3O4 results from increased reduction power, enhanced separation of electron–hole pairs, extended visible light absorption range, and optimized band structure by CTAB additive. The radical trapping experiments showed that the main reactive species during the photocatalytic reaction are superoxide ions. The developed photocatalysts may contribute to the development of environmental improvement technology.

chemistry, physical
Colorimetric determination of lead(II) or mercury(II) based on target induced switching of the enzyme-like activity of metallothionein-stabilized copper nanoclusters

Ran Liu,Li Zuo,Xiaorong Huang,Shimeng Liu,Guiying Yang,Shiya Li,Changyin Lv

DOI: https://doi.org/10.1007/s00604-019-3360-6

IF: 5.7

2019-03-19

Microchimica Acta

Abstract:It is shown that metallothionein-stabilized copper nanoclusters (MT-CuNCs) display catalase-like activity. In the presence of either lead(II) or mercury(II), the catalase-like activity is converted to a peroxidase-like activity. On addition of Pb(II) or Hg(II), the inhibitory effect of MT-CuNCs on the chromogenic reaction of 3,3′,5,5′-tetramethylbenzidine (TMB) with H2O2 is weakened. On the other hand, the catalytic effect of the nanoclusters on the chromogenic reaction is increased. The system MT-CuNCs-Pb(II)/Hg(II) exhibits high affinity for the substrates TMB and H2O2. Their catalytic behavior follows Michaelis-Menten kinetics. Based on these findings, a method was developed for visual detection (via the blue coloration formed) and spectrophotometric determination (at 450 nm) of Pb(II) and Hg(II). The linear range for Pb(II) extends from 0.7 to 96 μM, and the linear ranges for Hg(II) from 97 nM to 2.3 μM and from 3.1 μM to 15.6 μM. The detection limits are 142 nM for Pb(II) and 43.8 nM for Hg(II).Graphical abstractMetallothionein-stabilized copper nanoclusters (MT-CuNCs) display catalase-like activity. On addition of Pb(II) or Hg(II), the catalase-like activity is converted to a peroxidase-like activity. The latter catalyzes the oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) by H2O2.

chemistry, analytical
Nanoscale Imaging of Palladium-Enhanced Photocatalytic Reduction of 4-Nitrothiophenol on Tungsten Disulfide Nanoplates

Swati J. Patil,Dmitry Kurouski

DOI: https://doi.org/10.1021/acs.nanolett.4c03702

IF: 10.8

2024-10-08

Nano Letters

Abstract:Two-dimensional (2D) dichalcogenides are modern nanomaterials with unique physical and chemical properties. These materials possess band gaps in the infrared and visible regions of the electromagnetic spectrum that can be tuned by their molecular composition. Excitons generated as a result of such light-matter interactions are capable of catalyzing chemical reactions in molecular analytes present on the dichalcogenide surfaces. However, the photocatalytic properties of such nanomaterials remain...

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Determination of Trace Manganese by Catalytic Kinetic Spectrophotometry Method with CTMAB As the Sensitizer

Song Gui-lan,Ren Hao,Li Guo-bao,Yang Lin

DOI: https://doi.org/10.3321/j.issn:1000-0593.2006.08.041

2006-01-01

Abstract:A new catalytic spectrophotometric method for the determination of trace amount of Mn(II) was developed. The method is based on the oxidation of 7-(2-nitryl-4-methyl phenylazo)-8-hydroxy-qinolin-5-slfonic acid by potassium periodate in the presence of nitrilo triacec acid as an activator and CTMAB as a sensitizer. The wavelengths for the determination was 509 nm. The linear range of determination is 0-3. 2 x 10(-9) g x mL(-1) for Mn(II). The determination limit is 3.8 x 10(-11) g x mL(-1). The interference of foreign ions was studied. The method can be used for the determination of Mn(II) in mung bean, rice, cereal and soil samples.
Ultrahigh Selective Colorimetric Quantification of Chromium(VI) Ions Based on Gold Amalgam Catalyst Oxidoreductase-like Activity in Water.

Duoliang Shan,Shouting Zhang,Hong Xia,Wei Liu,Xiaoquan Lu,Xuehong Zhang,Zhen Zhang,Xuemei Li

DOI: https://doi.org/10.1021/acs.analchem.8b03597

IF: 7.4

2018-11-26

Analytical Chemistry

Abstract:Hexavalent chromium ion (Cr6+) is one of the most toxic substances for plants, for animals, and is a confirmed human respiratory carcinogen. However, so far, there are few independent and efficient colorimetric methods for detection of Cr6+. Here, we introduce a convenient, label-free, catalysis-based, and efficient strategy for quantification of Cr6+ by using a colorimetric sensing probe 3,3',5,5'-tetramethylbenzidine (TMB). In the presence of a trace amount of gold amalgam nanocomposites (Au@Hg) and Cr6+, TMB can be oxidized to oxTMB and the color changed to an intense blue that was observed by naked-eye and absorption spectroscopic method. In addition, the colorimetric method shows the high selectivity against 34 other interfering substances, and it can be performed at room temperature, in water, and requires only ∼5 min. Thus, the catalysis-based colorimetric assay for accurate and ultrahigh selective identification of Cr6+ will find widespread use in the world.

Medicine,Environmental Science,Chemistry
Synthesis of novel biomimetic photocatalyst and its use for visible light-assisted catalytic degradation of malachite green

GD Gao,JL Chen,SR Zheng,ZH Fei,FQ Liu,AM Li,XG Lu,QX Zhang

DOI: https://doi.org/10.3321/j.issn:0253-9837.2005.07.006

IF: 16.5

2005-01-01

Chinese Journal of Catalysis

Abstract:A novel catalyst named as HMS-FePcS has been synthesized for the first time by modifying the HMS molecular sieve with iron sulfophthalocyanine (FePcS), and characterized by XRD, TG, FT-IR, SEM and TEM. Under the visible light irradiation, this catalyst was highly efficient for the degradation of nonbiodegradable malachite green in aqueous solution in the presence of H2O2 , with decoloration rate of near 100 % and total organic carbon removal of 73 %. A possible reaction mechanism was also suggested.
Hydrothermal Synthesis and Photocatalytic Activity of NiTiO3 for the Degradation of Malachite Green under Visible Light Irradiation

Nour El Yakine Layachi,Hacene Bendjeffal,Abdelaziz Drici,Abdelkrim Djebli

DOI: https://doi.org/10.1002/slct.202304137

2024-01-30

ChemistrySelect

Abstract:Nickel titanate materials can be easily produced using a hydrothermal process. The diverse properties of this material open up the possibility of using it as an efficient, cost‐effective, and environmentally friendly catalyst for removing organic dyes from aqueous media. This study was dedicated to the development of an efficient, low‐cost, and environmentally friendly perovskite system for the elimination of recalcitrant dye from aqueous media by exploiting the photocatalytic performance of . The material was successfully obtained by hydrothermal synthesis in a Teflon batch‐type reactor system and then characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet‐visible spectroscopy (UV‐Vis), and Brunauer‐Emmett‐Teller analysis. The experimental analysis shows that after calcination at 800 °C, the phase is well crystallized. The as‐synthesized shows a band gap energy of and a surface area of 82.18 m2 −1. The degradation experiments were optimized using the One‐Factor‐at‐a‐Time strategy under the effect of four (4) operating factors, including catalyst dose (0.1–1) g L−1, medium pH (1–11), hydrogen peroxide concentration (0.025–0.250) , and initial dose (5–50) . The attained results illustrate that malachite green elimination increased with the rise of the H2O2 concentration and the catalyst dose. The optimum conditions determined at room temperature were = =0.5 g L−1, =0.250 , and pH 3 with a total removal efficiency (~100 %) achieved after 20 min of reaction. The results showed that the material is an outstanding visible‐light‐driven catalyst material for the photodegradation of MG under visible‐light irradiation.

chemistry, multidisciplinary
Optimizing the synthesis procedure and characterization of terbium(III) tungstate nanoparticles as high performance photocatalysts

Mehdi Rahimi-Nasrabadi,Seied Mahdi Pourmortazavi,Mohammad Reza Ganjali,Parviz Norouzi

DOI: https://doi.org/10.1007/s10854-017-6723-y

2017-04-09

Abstract:Through the application of Taguchi robust design (TRD), the operating parameters influencing the synthesis of terbium(III) tungstate nanoparticles via the chemical precipitation reaction were optimized. The overall reaction involved the direct addition of different aqueous terbium(III) solutions to those of tungstate ion solution, and the statistical approach was used to optimize the effects of the operating parameters on the size of the prepared terbium(III) tungstate particles. To this end, analysis of variance (ANOVA) evaluations were performed to evaluate the importance of the different variables including tungstate and terbium ion concentrations, the flow rate at which the cation was added to the tungstate solution (Fc) and the reaction temperature. After optimizing the synthesis procedure, terbium(III) tungstate nanoparticles were prepared under the optimal conditions, and their morphology and chemical composition were evaluated using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), FT-IR spectroscopy, and UV–Vis spectrometry. The optimal product was also evaluated as a photocatalyst in the UV-induced catalytic degradation of methyl orange (MO), and was found to possess an excellent activity for catalyzing this reaction, which can be regarded as an indication for its photocatalytic potentials for other similar reactions.
Improved photocatalytic properties of WO 3 nanoparticles for Malachite green dye degradation under visible light irradiation: An effect of La doping

Gokila Viswanathan,Ayyappan Solaiappan,Brindha Thirumalairaj,Umapathi Krishnamoorthy,Natrayan Lakshmaiya,Md Irfanul Haque Siddiqui,Mohd Asif Shah

DOI: https://doi.org/10.1515/chem-2024-0035

2024-01-01

Open Chemistry

Abstract:Abstract Doped materials have received substantial attention due to their increased usefulness in photocatalytic applications. Within this context, the present study was dedicated to investigating the potential of the precipitation technique for producing La-doped tungsten oxide (WO 3 ). To comprehensively characterize the synthesized La-doped WO 3 , scanning electron microscopy and X-ray diffraction were judiciously employed. The focal point of the investigation encompassed an examination of the impact of varying La concentrations on multiple fronts: the photocatalytic activities (PCAs), as well as any associated structural and morphological modifications. This holistic approach aimed to uncover the intricate relationship between La incorporation and the resulting properties of the WO 3 matrix. Through the degradation of Malachite green dye within an aqueous medium, PCA of the La-doped WO 3 samples was quantitatively evaluated. Remarkably, over 180 min under irradiation of visible light irradiation, the achieved levels of dye degradation were remarkable, amounting to 81.165, 83.11, and 83.85% for the respective samples. These findings firmly underscore the potential of La-doped WO 3 as a proficient photocatalyst, particularly in color removal from wastewater. This study paves the way for enhanced wastewater treatment approaches by utilizing doped WO 3 materials.

chemistry, multidisciplinary
Investigation of Catalytic Property of MnTSPc by Spectrophotometry

韩爱霞,梁强,牛丽红,郝丽,吴国是,张复实

DOI: https://doi.org/10.3969/j.issn.1000-0720.2004.08.015

2004-01-01

Abstract:Manganese-tetrasulfonatephthalocyanine catalyzed the oxidative condensation of 4-aminoantipyrine (4-AAP) with phenol and was monitored by spectrophotometry. The influence of surfactants were investigated. This reaction was used to measure hydrogen peroxide and glucose. The linear range of H_2O_2 was 1～50 mmol/L. At a H_2O_2 concentration of 1.0×10~(-3) mmol/L, the standard deviation was 1.9% for seven measurement. The linear range of glucose was 1～14 mmol/L.
Photocatalytic reduction of hexavalent chromium with commercial Fe/Ti oxide catalyst under UV and visible light irradiation

M. M. S. Sanad,E. A. Abdel-Aal,H. M. Osman,A. T. Kandil

DOI: https://doi.org/10.1007/s13762-017-1628-0

2017-10-31

International Journal of Environmental Science and Technology

Abstract:The photoreduction efficiency of toxic hexavalent chromium into non-toxic trivalent chromium was studied using local low-cost material and modern technology. The materials involved different iron–titanium oxide nanopowders synthesized via simple hydrothermal–hydrolysis process. X-ray diffraction and high-resolution transmission electron microscope were employed to study the structural properties of the as-prepared samples. The effects of molar ratio (Fe/Ti) and hydrothermal temperature on spectroscopic properties have been investigated using Fourier transform infrared FT-IR spectroscopy. The photocatalytic performance of hexavalent chromium was systematically studied at various conditions including initial concentration of Cr(VI), hydrothermal temperature and Fe/Ti ratios of mixed iron–titanium oxide powders. It has been found that the highest photoreduction efficiencies of Cr(VI) were 95.7 and 86.2% at initial concentrations 10 and 60 ppm of Cr(VI), respectively. The synthesized mixed Fe2O3–TiO2 photocatalyst exhibited higher efficiency of about 88% under visible light irradiation. The as-prepared mixed oxide catalyst exhibited high photocatalytic conversion efficiency and recycling stability in comparison with different commercial catalysts.

environmental sciences

Catalytic spectrophotometric determination of tungsten using the malachite green-Ti(III) redox reaction and a thiocyanate activator.

Preparation of WO<sub>x</sub>-TiO<sub>2</sub> and the Photocatalytic Activity under Visible Irradiation

Microstructure and performance of Z-scheme photocatalyst of silver phosphate modified by MWCNTs and Cr-doped SrTiO3 for malachite green degradation

Extraction System for the Spectrophotometric Determination of Tungsten(VI) with 4-Nitrocatechol and Benzalkonium Chloride

Quantification of tungsten in real samples spectrophotometrically using optical sensor

Spectrophotometric Determination of Chromium in Waste Water and Soil.

A Novel Visible Light-Driven TiO2 Photocatalytic Reduction for Hexavalent Chromium Wastewater and Mechanism

A MWCNTs@CuAl2O4@SiO2 Nanocomposite for the Speciation of Cr(III), Cr(VI), and Total Chromium Prior to High-Resolution Continuum Source Flame Atomic Absorption Spectrometric Determination

Chromogenic reaction for tungsten (VI)-4-(6-bromo-2-benzothiazolylazo )pyrocatechol -emulsifier OP micellar complex and its application

Novel Spectrophotometric Method for the Determination of Molybdenum in a PVA Medium

Synthesis of Tungsten-Modified Sn3O4 through the Cetyltrimethylammonium Bromide-Assisted Solvothermal Method for Dye Decolorization under Visible Light Irradiation

Colorimetric determination of lead(II) or mercury(II) based on target induced switching of the enzyme-like activity of metallothionein-stabilized copper nanoclusters

Nanoscale Imaging of Palladium-Enhanced Photocatalytic Reduction of 4-Nitrothiophenol on Tungsten Disulfide Nanoplates

Determination of Trace Manganese by Catalytic Kinetic Spectrophotometry Method with CTMAB As the Sensitizer

Ultrahigh Selective Colorimetric Quantification of Chromium(VI) Ions Based on Gold Amalgam Catalyst Oxidoreductase-like Activity in Water.

Synthesis of novel biomimetic photocatalyst and its use for visible light-assisted catalytic degradation of malachite green

Hydrothermal Synthesis and Photocatalytic Activity of NiTiO3 for the Degradation of Malachite Green under Visible Light Irradiation

Optimizing the synthesis procedure and characterization of terbium(III) tungstate nanoparticles as high performance photocatalysts

Improved photocatalytic properties of WO 3 nanoparticles for Malachite green dye degradation under visible light irradiation: An effect of La doping

Investigation of Catalytic Property of MnTSPc by Spectrophotometry

Photocatalytic reduction of hexavalent chromium with commercial Fe/Ti oxide catalyst under UV and visible light irradiation