[Medical gerontology. Metabolism and endocrinology].

P. Berthaux,M. Beck

Abstract:

What problem does this paper attempt to address?

Mechanical Properties Of 7-10 Mm Bone Grafts And Small Slurry Grafts In Impaction Bone Grafting

Zheng-Jian Xu,Lian-Yi Chen,Cheng Zhong,Yan-Bin Tan,Rong-Xin He

DOI: https://doi.org/10.1002/jor.21357

2011-01-01

Journal of Orthopaedic Research

Abstract:We compared the mechanical properties of morselized cancellous bone grafts of two sizes: 7-10 mm bone and small slurry bone (about 2 mm). The in vitro test was designed to simulate the hammer and impactor system for impaction bone grafting used in hip arthroplasty clinical practice. The 7-10 mm bone grafts showed higher height, elastic modulus, and massive extrusion strength than those of the small slurry bone grafts. No difference was found in yield strength. The bone mineral density of the 7-10 mm grafts continued to increase during impaction and became higher than that of the small slurry bone grafts after 10 impactions. Our results demonstrated that the small slurry bone grafts exhibit worse mechanical properties as compared with the 7-10 mm bone grafts, which implies that the use of this material in reconstruction of a bone defect in the acetabulum should be limited. (C) 2011 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 29:1491-1495, 2011
Effects of Low-Frequency Pulsed Wave Ultrasound on the Shear Properties of the Interface of Vancomycin-Loaded Acrylic Bone Cement-Stem

Q H Zhao,F B Zhu,X Z Cai,S G Yan,R X He

DOI: https://doi.org/10.3760/cma.j.issn.0376-2491.2017.07.015

2017-01-01

Abstract:Objective: To investigate the effects of low-frequency pulsed wave ultrasound on the shear properties of interface of the vancomycin -loaded acrylic bone cement-stem. Methods: The interfaces of 1% vancomycin-loaded acrylic bone cement-stem specimences were successfully manufactured and randomly divided into three groups: the control group, 450 mW/cm(2) ultrasound group and 1 200 mW/cm(2) ultrasound group, each group consisted of eight samples.Two ultrasound groups were exposed to a local ultrasonic field for 7 d, then immersed in PBS for 23 d, and the control groups were immersed in PBS for 30 d. After curing in air for 24 h, the shear strength of the stem-cement interface was determined by push-out test.The specimens were then photographed using SEM and analysed using Image-Pro Plus 6.0 to determine the porosity at the stem-cement interface. Results: The mean shear strength of stem-cement interface additionally decreased by 9% (P>0.05) and 17% (P<0.05) in 450 mW/cm(2) ultrasound group and 1 200 mW/cm(2) group respectively comparing with the control group, but no significant difference was found between the two ultrasound groups.The porosity at the stem-cement interface additionally increased by 44% (P>0.05) and 110% (P<0.05) in 450 mW/cm(2) ultrasound group and 1 200 mW/cm(2) group respectively comparing with the control group, furthermore.The porosity in 1 200 mW/cm(2) ultrasound group increased by 46% (P<0.05) comparing with the 450 mW/cm(2) group. There are much more fluid penetration along the stem-cement interface in ultrasound group . Conclusion: Low-frequency pulsed wave ultrasound signifiantly enhanced porosity and fluid penetration interface, and reduced the interface shear strength and initial stability.
Mechanical Properties and Porosity of Acrylic Cement Bone Loaded with Alendronate Powder

Guo-Xin Qu,Zhi-Min Ying,Chen-Chen Zhao,Shi-Gui Yan,Xun-Zi Cai

DOI: https://doi.org/10.7150/ijms.27759

2018-01-01

International Journal of Medical Sciences

Abstract:Aseptic loosening is the most common complication of joint replacement. Previous studies showed that acrylic bone cement loaded with a commercially-available alendronate powder (APAC) had good promise against wear debris-mediated osteolysis for prevention of aseptic loosening. The purpose of the present study was to investigate the effect of adding alendronate powder to an acrylic bone cement on quasi-static mechanical properties (namely, compressive strength, compressive modulus, tensile strength, and flexural strength), fatigue life, porosity, and microstructure of the cement. The results showed that adding up to 1 wt./wt.% alendronate powder exerted no detrimental effect on any of the quasi-static mechanical properties. However, the fatigue life of APAC decreased by between ~17% and ~27 % and its porosity increased by between ~ 5-7 times compared with corresponding values for the control cement (no alendronate powder added). Fatigue life was negatively and significantly correlated with porosity. Considering that fatigue life of the cement plays a significant role in joint replacement survival, clinical use of APAC cannot be recommended.
Effect of Delayed Pulsed-Wave Ultrasound on Local Pharmacokinetics and Pharmacodynamics of Vancomycin-Loaded Acrylic Bone Cement in Vivo

Xun-Zi Cai,Shi-Gui Yan,Hao-Bo Wu,Rong-Xin He,Xue-Song Dai,Hai-Xiang Chen,Rui-Jian Yan,Xin-Hua Zhao

DOI: https://doi.org/10.1128/aac.01465-06

IF: 5.938

2007-01-01

Antimicrobial Agents and Chemotherapy

Abstract:ABSTRACT This study sought to investigate the effect of delayed pulsed-wave ultrasound with low frequency on drug release from and the antimicrobial efficacy of vancomycin-loaded acrylic bone cement in vivo and the possible mechanism of this effect. After the implantation of cement and the inoculation of Staphylococcus aureus into the bilateral hips of rabbits, ultrasound (average intensity, 300 mW/cm2; frequency, 46.5 kHz; on/off ratio, 20 min/10 min) was applied to animals in the normal ultrasound group (UG0-12) from 0 through 12 h after surgery and to those in the delayed-ultrasound group (UG12-24) from 12 through 24 h after surgery. The control group (CG) was not exposed to ultrasound. Based on vancomycin concentrations in left hip cavities at projected time intervals, the amount of time during which the local drug concentration exceeded the MIC (T>MIC) in UG12-24 was significantly prolonged compared with that in either CG or UG0-12, and the ratios between the areas under the concentration-time curves over 24 h and the MIC for UG0-12 and UG12-24 were both increased compared with that for CG. The greatest reductions in bacterial densities in both right hip aspirates and right femoral tissues at 48 h were achieved with UG12-24. Local hemorrhage in rabbits of UG0-12 during the 12-h insonation was more severe than that in rabbits of UG12-24. Of four variables, the T>MIC and the bioacoustic effect were both identified as parameters predictive of the enhancement of the antimicrobial efficacy of cement by ultrasound. Sustained concentrations above the MIC replaced early high maximum concentrations and long-term subtherapeutic release of the drug, provided that ultrasound was not applied until local hemorrhage was relieved. The enhancement of the antimicrobial efficacy of cement by ultrasound may be attributed to the prolonged T>MIC and the bioacoustic effect caused by ultrasound.
Effects of lead inhalation exposures alone and in combination with carbon monoxide in nonpregnant and pregnant rats and fetuses. I. Distribution of lead in blood and liver.

E. Prigge,H. Baumert,D. Hochrainer,G. Oberdörster

1977-12-01

Abstract:Nonpregnant and pregnant rats were continuously exposed for 3 weeks to an aerosol containing 1, 3 and 10 mg lead/m3 air and to a combination of 3 mg Pb/m3 and 500 ppm carbon monoxide. At the two lower lead doses, fetal blood lead levels exceeded those of the mothers. Active transport mechanisms were discussed to be responsible for these differences. A decrease of the fetal blood lead level below the maternal level in the high exposure group was explained by an increasing storage capacity of the fetal livers with increasing lead doses. Lead concentrations of the maternal livers exceeded the nonpregnant values at all 3 doses, probably caused by a higher ventilation and altered pharmacokinetics of lead in pregnancy. Additional CO-inhalation lowered the storage capacity of the livers of the adult animals and raised the blood concentration. In the fetuses additional CO-inhalation raised liver lead concentrations.
Effect of Ultrasound on Drug Release of Vancomycin-Loaded Acrylic Bone Cement

严世贵,蔡迅梓,张建良,吴浩波

DOI: https://doi.org/10.3760/j.issn:0253-2352.2006.03.011

2006-01-01

Abstract:Objective To investigate the effect of low-frequency ultrasound on the release of vancomycin from antibiotic-loaded bone cement (ALBC) and its regularity in vitro and in vivo. Methods ALBC specimens were successfully manufactured for in vitro and in vivo assays. 5% and 10% ALBC specimens were both randomly divided into three groups: the control group, 100 mW/cm2 ultrasound group and 300 mW/cm2 ultrasound group. After immersing in PBS of 40 ml for 8 h, the four ultrasound groups were exposed to a timed local ultrasonic field for 30 min, then the drug cumulative concentrations were observed during a 2.5 h period after exposure and on the 24th hour after immersion. Sixteen healthy New Zealand white rabbits were divided randomly into two groups: the ultrasound group was exposed to a local timed intermittent ultrasound field and the control group not. Samples of drainage fluid and urine were collected at programmed intervals during a 5 d period, and the ALBC specimens were extracted from rabbits four weeks after implantations with all their concentrations measured by fluorescence polarization immunoassay (FPIA). Results After immersing 24 h in vitro, the cumulative concentration of vancomycin additionally increased by 71.77% and 73.62% in 10% 100 mW/cm2 ultrasound group and 300 mW/cm2 group respectively comparing with 10% control group; while increased 13.03% and 23.78% in 5% 100 mW/cm2 and 300 mW/cm2 groups comparing with 5% control group. Furthermore, the total release was positively correlated with the ultrasound intensity (P 0.05) and the amount of vancomycin loaded in specimens (P 0.01). The total release of vancomycin increased by 148.18% (P 0.01) and 82.39% (P 0.05) in 7.5% specimens during a 1 d period and a 5 d period in vivo, respectively, caused by intermittent 30 min exposures of ultrasound with an intensity of 300 mW/cm2. More decreased residue of vancomycin was detected in the ultrasound group than in the control group four weeks after implantations (P 0.01). Conclusion Low-frequency low-intensity continuous ultrasound may provide an effective method to enhance and accelerate the vancomycin release of ALBC.
Does the Addition of Low-Dose Antibiotics Compromise the Mechanical Properties of Polymethylmethacrylate (PMMA)?

Valentina Egger,Dietmar Dammerer,Gerald Degenhart,Johannes D. Pallua,Werner Schmölz,Martin Thaler,Klaus-Dieter Kühn,Michael Nogler,David Putzer

DOI: https://doi.org/10.3390/polym16162378

IF: 5

2024-08-24

Polymers

Abstract:The increasing numbers of total joint replacements and related implant-associated infections demand solutions, which can provide a high-dose local delivery of antibiotics. Antibiotic-loaded bone cement (ALBC) is an accepted treatment method for infected joint arthroplasties. The mechanical properties of low-dose gentamicin-loaded bone cement (BC) in medium- and high-viscosity versions were compared to unloaded BC using a vacuum mixing system. As an additional control group, manual mixed unloaded BC was used. In a uniaxial compression test, ultimate compressive strength, compressive yield strength, and compression modulus of elasticity, as well as ultimate and yield strain, were determined according to ISO 5833-2022 guidelines. All groups exceeded the minimum compressive strength (70 MPa) specified in the ISO 5833 guidelines. Both ALBC groups showed a similar ultimate compressive and yield strength to the unloaded BC. The results showed that vacuum mixing increased the compression strength of BC. ALBC showed similar compressive strength to their non-antibiotic counterparts when vacuum mixing was performed. Added low-dose gentamicin acted as a plasticizer on bone cement. From a biomechanical point of view, the usage of gentamicin-based ALBC formulations is viable.

polymer science
Intermittent watt-level ultrasonication facilitates vancomycin release from therapeutic acrylic bone cement.

Xun-Zi Cai,Xian-Zhen Chen,Shi-Gui Yan,Zou-Rong Ruan,Rui-Jian Yan,Kang Ji,Jia Xu

DOI: https://doi.org/10.1002/jbm.b.31288

2009-01-01

Abstract:Ultrasound holds promise for enhancing the vancomycin release from cement though the length of time when local drug level exceeded the minimum inhibitory concentration (T->MIC) was not prolonged by the previous protocol of milliwatt-level ultrasonication. Here vancomycin-loaded cements were subjected to continuous watt-level ultrasonication (CUG), intermittent watt-level ultrasonication (IUG) or no ultrasonication (NUG) for 14 d during immersion in 40-ml phosphate buffered saline (PBS) for 28 d. The T->MIC for IUG was more than three times that for NUG. In contrast, T->MIC for CUG was slightly shortened. The subtherapeutic release of vancomycin between 15 d and 28 d for IUG was one-ninth that for NUG. The fitting equations indicated a significant enhancement on the burst release and the slow release for IUG; however, the continuous ultrasonication hampered the slow release. SEM images exhibited denser craters and pores with larger diameters and less residual drug in specimens from IUG relative to those from both CUG and NUG. Intermittent watt-level ultrasonication improved the ultrasound-enhanced vancomycin release from cement in view of the prolonged T->MIC and the inhibited subtherapeutic release compared with continuous ultrasonication. The mechanisms may be associated with the distinctive effects of detaching forces and pushing forces by acoustic microstreams. (C) 2008 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 90B: 11-17, 2009
Planned Caesarean section for term breech delivery.

G. Hofmeyr,M. Hannah

DOI: https://doi.org/10.1002/14651858.cd000166.pub2

IF: 8.4

Cochrane Database of Systematic Reviews

Abstract:BACKGROUND Routine use of caesarean section for breech presentation is widespread. However, poor outcomes after breech birth might be the result of underlying conditions causing breech presentation rather than damage during delivery. OBJECTIVES The objective of this review was to assess the effects of planned caesarean section for breech presentation on measures of pregnancy outcome. SEARCH STRATEGY We searched the Cochrane Pregnancy and Childbirth trials register and the Cochrane Controlled Trials register. Date of last search: November 2000. SELECTION CRITERIA Randomised trials comparing planned caesarean section for breech presentation with planned vaginal delivery. DATA COLLECTION AND ANALYSIS Reviewers assessed trial eligibility and quality. Data were entered onto and analysed using RevMan software. MAIN RESULTS Caesarean delivery occurred in 550/1227 (45%) of those women allocated to a vaginal delivery protocol. Planned caesarean section was associated with modestly increased maternal morbidity (relative risk 1.29, 95% confidence interval 1.03 to 1.61). Perinatal and neonatal death (excluding fatal anomalies) were greatly reduced (0.29, 0.10 to 0.86). The reductions were similar for countries with low and high perinatal mortality rates. Perinatal/neonatal death or neonatal morbidity was also greatly reduced (0.31, 0.19 to 0.52). The difference was smaller for countries with a high national perinatal mortality rate. REVIEWER'S CONCLUSIONS Planned caesarean section greatly reduces both perinatal/neonatal mortality and neonatal morbidity, at the expense of somewhat increased maternal morbidity. Cost, and future morbidity due to the caesarean section scar were not assessed. The option of external cephalic version is dealt with in separate reviews. The data from this review will help to inform individualised decision-making regarding breech delivery.
Bioactive poly (methyl methacrylate) bone cement for the treatment of osteoporotic vertebral compression fractures

Jinjin Zhu,Shuhui Yang,Kaiwen Cai,Shuo Wang,Zhiye Qiu,Junfei Huang,Guoqiang Jiang,Xiumei Wang,Xiangqian Fang

DOI: https://doi.org/10.7150/thno.44428

IF: 11.6

2020-01-01

Theranostics

Abstract:Rationale: Poly (methyl methacrylate) (PMMA) bone cement is one of the most commonly used biomaterials for augmenting/stabilizing osteoporosis-induced vertebral compression fractures (OVCFs), such as percutaneous vertebroplasty (PVP) and balloon kyphoplasty (BKP). However, its clinical applications are limited by its poor performance in high compressive modulus and weak bonding to bone. To address these issues, a bioactive composite bone cement was developed for the treatment of osteoporotic vertebral compression fractures, in which mineralized collagen (MC) was incorporated into the PMMA bone cement (MC-PMMA). Methods: The in vitro properties of PMMA and MC-PMMA composite bone cement were determined, including setting time, compressive modulus, adherence, proliferation, and osteogenic differentiation of rat bone mesenchymal stem cells. The in vivo properties of both cements were evaluated in an animal study (36 osteoporotic New Zealand female rabbits divided equally between the two bone cement groups; PVP at L5) and a small-scale and short-term clinical study (12 patients in each of the two bone cement groups; follow-up: 2 years). Results: In terms of value for PMMA bone cement, the handling properties of MC-PMMA bone cement were not significantly different. However, both compressive strength and compressive modulus were found to be significantly lower. In the rabbit model study, at 8 and 12 weeks post-surgery, bone regeneration was more significant in MC-PMMA bone cement (cortical bone thickness, osteoblast area, new bone area, and bone ingrowth %; each significantly higher). In the clinical study, at a follow-up of 2 years, both the Visual Analogue Score and Oswestry Disability Index were significantly reduced when MC-PMMA cement was used. Conclusions: MC-PMMA bone cement demonstrated good adaptive mechanical properties and biocompatibility and may be a promising alternative to commercial PMMA bone cements for the treatment of osteoporotic vertebral fractures in clinical settings. While the present results for MC-PMMA bone cement are encouraging, further study of this cement is needed to explore its viability as an ideal alternative for use in PVP and BKP.
Rheological and Curing Behavior of a Newly Developed, Medium Viscous Acrylic Bone Cement

Stefan Deusser,Christoph Sattig,Andreas Boger

DOI: https://doi.org/10.5402/2011/571728

2011-10-09

ISRN Materials Science

Abstract:Percutaneous vertebroplasty, comprising an injection of polymethylmethacrylate (PMMA) bone cement into vertebral bodies, is a practical procedure for stabilization of osteoporotic compression fractures and other weakening lesions. Cement leakage is considered to be the major complication. The viscosity plays a key role in this context. At high viscosity, the risk of leakage is reduced; however, injection forces are highly increased, handling time is reduced. The purpose of the study was to investigate the rheological, handling and hardening behaviour of a newly developed medium viscous bone cement at different temperatures and by simulation of a temperature shift to body-temperature. The presented data give an impression on the injectability of the cement using different sized needles. It could be concluded, that the medium viscous cement shows an adequate working time for a broad temperature range and an acceptable hardening time of around 11 min after immersing the cement into a C environment.
In Vitro and in Vivo Evaluation of Vancomycin-Loaded PMMA Cement in Combination with Ultrasound and Microbubbles-Mediated Ultrasound

Tiao Lin,Xun-Zi Cai,Ming-Min Shi,Zhi-Min Ying,Bin Hu,Chen-He Zhou,Wei Wang,Zhong-Li Shi,Shi-Gui Yan

DOI: https://doi.org/10.1155/2015/309739

2015-01-01

BioMed Research International

Abstract:Ultrasound (US) has been used to increase elution of antibiotic from an antibiotic-loaded poly(methyl methacrylate) (PMMA) bone cement (ALBC). We aimed to further investigate whether microbubbles-mediated US (US + MB) facilitate elution of vancomycin (VAN) from cylindrical specimens and enhance the activity of the eluted antibiotic againstStaphylococcus aureus(S. aureus) in vitro. The study groups comprised cylindrical bone cement fabricated with VAN (VAN), ALBC using US (VAN + US), and ALBC using MB-mediated US (VAN + US + MB). We also carried out an in vivo study involving the activity of VAN from cylindrical cement implanted in tibiae of New Zealand white rabbits inoculated withS. aureus. We found that (1) in vitro, elution from VAN + US + MB cylinders was significantly higher than from either the VAN or VAN + US specimens; (2) the activity of the eluted VAN from the VAN + US + MB cylinders against planktonicS. aureuswas significantly higher than from either the control or VAN or VAN + US specimens; and (3) in the rabbits, the activity of the eluted VAN from the VAN + US + MB cylinders againstS. aureuswas significantly higher than from either the control or VAN or VAN + US specimens. The present results suggest that VAN-loaded PMMA cement irradiated with MB-mediated US may have a role in controlling prosthetic joint infection.
Influence of vacuum mixing on the mechanical properties of UHPC

V. Boel,G. Schutter,Egon Braem,J. Dils

Abstract:The influence of vacuum mixing of UHPC on the compressive and tensile strength, and Young's modulus is examined. These mechanical properties are influenced by the microstructure and the pore system. Classical models predicting these properties based on the water-to-cement ratio do not consider the effect of vacuum mixing, which is quite new. This will be even more important in the case of UHPC because of the extremely low water-to-cement ratio and the larger influence of changes in air content. In this research, two different mixer sizes are considered : a vacum paste mixer (capacity of 5 liter) and a vacuum concrete mixer (capacity of 75 liter). For each mixer, three different pressure levels are examined : vacuum (100 mbar), semi-vacuum (500 mbar) and atmospheric pressure (1013 mbar). The influence of heat treatment (90°C) in CoMParison or combination with vacuum mixing is evaluated by means of the compressive strength on concrete cubes 100 mm.

Materials Science,Engineering,Environmental Science
HOW DOES CEMENT VOLUME INFLUENCE THE MECHANICAL EFFECTS OF VERTEBROPLASTY

Patricia Dolan,Jianbin Luo,Luke Daines,Alexander Charalambous,DJ Annesley-Williams,Michael A. Adams

2009-01-01

Abstract:Introduction: The aim of this cadaver study was to examine how cement volume used in vertebroplasty influences the restoration of normal load-sharing and stiffness to fractured vertebrae. Methods: Nineteen thoracolumbar motion segments obtained from 13 spines (42–91 yrs) were compressed to failure in moderate flexion to induce vertebral fracture. Fractured vertebrae underwent two sequential vertebroplasty treatments (VP1 and VP2) each of which involved unipedicular injection of 3.5ml of polymethyl-methacrylate cement. During each injection, the volume of any cement leakage was recorded. At each stage of the experiment (pre-fracture, post-fracture, post-VP1 and post-VP2) measurements were made of motion segment stiffness, in bending and compression, and the distribution of compressive stress across the disc. The latter was measured in flexed and extended postures by pulling a pressure transducer through the mid-sagittal diameter of the disc whilst under 1.5kN load. Stress profiles indicated the intradiscal pressure (IDP), stress peaks in the posterior annulus (SPP), and neural arch compressive load-bearing (FN). Measurements obtained after VP1 and VP2 were compared with pre-fracture and post-fracture values using repeated measures ANOVA to examine the effect of cement volume (3.5 ml vs. 7 ml) on the restoration of mechanical function. Results: Fracture reduced compressive and bending stiffness by 50% and 37% respectively (p Conclusions: Unipedicular injection of 3.5 ml of cement reversed fractured induced changes in IDP and SPP, but did not affect stiffness and neural arch load-bearing. Larger injection volumes may provide some extra mechanical benefit in terms of restoring stiffness and reducing neural arch loading, but these extra mechanical benefits can be at the cost of increased risk of cement leakage.
A Biomechanical Study on Cortical Bone Trajectory Screw Fixation Augmented with Cement in Osteoporotic Spines.

Yuetian Wang,Lei Yang,Chunde Li,Haolin Sun

DOI: https://doi.org/10.1177/21925682211070826

2022-01-01

Global Spine Journal

Abstract:Study Design A biomechanical study. Objective To evaluate the efficacy and feasibility of cement-augmented cortical bone trajectory (CBT) screw fixation. Methods Forty-nine CBT screws were inserted into lumbar vertebrae guided by three-dimensionally printed templates, and then injected with 0, .5, or 1.0 mL of polymethylmethacrylate. The screw placement accuracy, cement dispersion, and cement leakage rate were evaluated radiologically. Biomechanical tests were performed to measure the axial pull-out strength and torque value. Results Overall, 83.67% of the screws were inserted without pedicle perforation. In the 1.0 mL group, cement dispersed into the pedicle zone and formed a concentrated mass more often than in the .5 mL group, but not significantly more often (P > .05). The total cement leakage rate was 18.75%. Compared with the control group, the torque value was slightly higher in the .5 mL group (P = .735) and significantly higher in the 1.0 mL group (P = .026). However, there was no significant difference between the .5 and 1.0 mL groups (P = .431). The maximal pull-out force (Fmax) was increased by 52.85% and 72.73% in the .5 and 1.0 mL groups, respectively, compared with the control group (P < .05). However, the difference was not significant between the 2 cemented groups (P = .985). Conclusions Cement augmentation is a useful method for increasing CBT screw stability in osteoporotic spines. The cement injection volume is recommended to be 1 mL for each screw, and the cement should disperse into the vertebral body than the pedicle zones.
Biomechanical evaluation of bone screw fixation with a novel bone cement

Tiina Juvonen,Juha-Pekka Nuutinen,Arto P Koistinen,Heikki Kröger,Reijo Lappalainen

DOI: https://doi.org/10.1186/s12938-015-0069-6

2015-07-30

Abstract:Background: Bone cement augmentation is commonly used to improve the fixation stability of orthopaedic implants in osteoporotic bone. The aim of this study was to evaluate the effect of novel bone cements on the stability of bone screw fixation by biomechanical testing and to compare them with a conventional Simplex(®)P bone cement and requirements of the standards. Methods: Basic biomechanical properties were compared with standard tests. Adhesion of bone cements were tested with polished, glass blasted and corundum blasted stainless steel surfaces. Screw pullout testing with/without cement was carried out using a synthetic bone model and cancellous and cortical bone screws. Results: All the tested bone cements fulfilled the requirements of the standard for biomechanical properties and improved the screw fixation stability. Even a threefold increase in shear and tensile strength was achieved with increasing surface roughness. The augmentation improved the screw pullout force compared to fixation without augmentation, 1.2-5.7 times depending on the cement and the screw type. The good biomechanical properties of novel bone cement for osteoporotic bone were confirmed by experimental testing. Conclusion: Medium viscosity of the bone cements allowed easy handling and well-controlled penetration of bone cement into osteoporotic bone. By proper parameters and procedures it is possible to achieve biomechanically stable fixation in osteoporotic bone. Based on this study, novel biostable bone cements are very potential biomaterials to enhance bone screw fixation in osteoporotic bone. Novel bone cement is easy to use without hand mixing using a dual syringe and thus makes it possibility to use it as required during the operation.
High-Viscosity Versus a Lower-Viscosity Cement Penetration at Dough Phase In Vivo in Primary Total Knee Arthroplasty

Michael G Rizzo,Anya T Hall,Justin T Downing,Raymond P Robinson

DOI: https://doi.org/10.1016/j.arth.2021.02.010

Abstract:Background: Previous studies have shown that the depth of cement penetration and the presence of radiolucent lines (RLLs) correspond with the risk of aseptic loosening in total knee arthroplasty, while others have found a correlation between the viscosity of the cement and the depth of cement penetration. We compared cement marketed as high-viscosity cement (HVC) with one marketed by the same manufacturer as low-viscosity cement (LVC). We hypothesized that no significant difference would be found in depth of penetration or presence of RLLs between the two cohorts. Methods: The HVC (n = 50) and LVC cohorts (n = 50) were gathered from two sequential series of primary total knee arthroplasties using the same implants and cementing techniques. Depth of cement penetration and presence of RLL were measured in four tibial zones and were compared between cohorts. Results: There were no cases of aseptic loosening in either cohort at a mean of 29 months. Mean maximum cement penetration in 3 of the 4 zones was >3 mm with both cements. There was no significant difference in maximum penetration in any zone between the two cements. There were fewer tibial radiolucencies with HVC than LVC. Conclusion: These findings suggest that the marketing description of HVC or LVC is not necessarily a factor in cement penetration. The term high viscosity should not be used as a descriptor of cement that reaches dough phase more quickly, but rather cement that has a higher viscosity at its dough phase when it is typically applied.
Mechanical Properties And Cytocompatibility Improvement Of Vertebroplasty Pmma Bone Cements By Incorporating Mineralized Collagen

Hong-Jiang Jiang,Jin Xu,Zhi-Ye Qiu,Xin-Long Ma,Zi-Qiang Zhang,Xun-Xiang Tan,Yun Cui,Fu-Zhai Cui

DOI: https://doi.org/10.3390/ma8052616

IF: 3.4

2015-01-01

Materials

Abstract:Polymethyl methacrylate (PMMA) bone cement is a commonly used bone adhesive and filling material in percutaneous vertebroplasty and percutaneous kyphoplasty surgeries. However, PMMA bone cements have been reported to cause some severe complications, such as secondary fracture of adjacent vertebral bodies, and loosening or even dislodgement of the set PMMA bone cement, due to the over-high elastic modulus and poor osteointegration ability of the PMMA. In this study, mineralized collagen (MC) with biomimetic microstructure and good osteogenic activity was added to commercially available PMMA bone cement products, in order to improve both the mechanical properties and the cytocompatibility. As the compressive strength of the modified bone cements remained well, the compressive elastic modulus could be significantly down-regulated by the MC, so as to reduce the pressure on the adjacent vertebral bodies. Meanwhile, the adhesion and proliferation of pre-osteoblasts on the modified bone cements were improved compared with cells on those unmodified, such result is beneficial for a good osteointegration formation between the bone cement and the host bone tissue in clinical applications. Moreover, the modification of the PMMA bone cements by adding MC did not significantly influence the injectability and processing times of the cement.
Static shear strength between polished stem and seven commercial acrylic bone cements

Hongyu Zhang,Leigh Brown,Liam Blunt

DOI: https://doi.org/10.1007/s10856-007-3211-6

2007-01-01

Abstract:The stem–cement interface is one of the most significant sites in cemented total hip replacement and has long been implicated in failure of the whole joint system. However, shear strength at this interface has rarely been compared across a range of commercially available bone cements. The present study seeks to address this issue by carrying out a comparative study. The results indicated that the static shear strength was more dependent on cement type than cement viscosity and volume. However, both cement type and viscosity were contributory factors on porosity and micropore size in the cement surface. There was no significant difference between Simplex P and Simplex P with Tobramycin. Although the bone cements were all hand mixed in this study, the static shear strength was significantly larger than the values recorded by other researchers, and the porosity and micropore size showed much lower values. Bone cement transfer films were detected on the stem surface, typically about 4–10 μm thick. They were considered to be an important factor contributing to high friction at the stem–cement interface after initial debonding.
Experimental and numerical analysis of the mechanical behavior of bone cement reinforced with alumina particles

DOI: https://doi.org/10.1007/s40430-023-04283-x

IF: 2.361

2023-06-23

Journal of the Brazilian Society of Mechanical Sciences and Engineering

Abstract:The failure of polymethyl methacrylate (PMMA) orthopedic cement is considered the most important problem in total hip arthroplasty and eventual prosthesis loosening. Fiber or particulate reinforcement has been used to improve the mechanical properties of bone cement. However, reinforced cements have also been limited by adhesion between the PMMA and implant. This study investigated the effect of bioceramic particle reinforcement (alumina; Al 2 O 3 ) with different volumes (0, 5, 10, 15 and 20 vol%) on both the mechanical behavior of bone cements and implant–cement interface resistance. Mechanical fixation at the implant–cement interface was evaluated in vitro under shear mode loading conditions. Based on the mechanical tests of the implant–cement interface, a finite element model of the interface sample was developed to analyze the interfacial behavior of the implant–cement adhesion. The results show that the highest elastic modulus, tensile strength, compressive strength, and Vickers hardness (5.01 GPa, 41.33 MPa, 100.26 MPa and 10.36, respectively) were obtained using the PMMA sample with 20 vol% alumina particles, which represent increases of 82.8%, 78.68%, 42.37% and 282%, respectively, compared with those of pure PMMA. Against all expectations, beyond 10 vol% alumina, the interface strength dropped. The results also show that there is a good correlation between the numerical and experimental analysis methods.

engineering, mechanical

[Medical gerontology. Metabolism and endocrinology].

Mechanical Properties Of 7-10 Mm Bone Grafts And Small Slurry Grafts In Impaction Bone Grafting

Effects of Low-Frequency Pulsed Wave Ultrasound on the Shear Properties of the Interface of Vancomycin-Loaded Acrylic Bone Cement-Stem

Mechanical Properties and Porosity of Acrylic Cement Bone Loaded with Alendronate Powder

Effect of Delayed Pulsed-Wave Ultrasound on Local Pharmacokinetics and Pharmacodynamics of Vancomycin-Loaded Acrylic Bone Cement in Vivo

Effects of lead inhalation exposures alone and in combination with carbon monoxide in nonpregnant and pregnant rats and fetuses. I. Distribution of lead in blood and liver.

Effect of Ultrasound on Drug Release of Vancomycin-Loaded Acrylic Bone Cement

Does the Addition of Low-Dose Antibiotics Compromise the Mechanical Properties of Polymethylmethacrylate (PMMA)?

Intermittent watt-level ultrasonication facilitates vancomycin release from therapeutic acrylic bone cement.

Planned Caesarean section for term breech delivery.

Bioactive poly (methyl methacrylate) bone cement for the treatment of osteoporotic vertebral compression fractures

Rheological and Curing Behavior of a Newly Developed, Medium Viscous Acrylic Bone Cement

In Vitro and in Vivo Evaluation of Vancomycin-Loaded PMMA Cement in Combination with Ultrasound and Microbubbles-Mediated Ultrasound

Influence of vacuum mixing on the mechanical properties of UHPC

HOW DOES CEMENT VOLUME INFLUENCE THE MECHANICAL EFFECTS OF VERTEBROPLASTY

A Biomechanical Study on Cortical Bone Trajectory Screw Fixation Augmented with Cement in Osteoporotic Spines.

Biomechanical evaluation of bone screw fixation with a novel bone cement

High-Viscosity Versus a Lower-Viscosity Cement Penetration at Dough Phase In Vivo in Primary Total Knee Arthroplasty

Mechanical Properties And Cytocompatibility Improvement Of Vertebroplasty Pmma Bone Cements By Incorporating Mineralized Collagen

Static shear strength between polished stem and seven commercial acrylic bone cements

Experimental and numerical analysis of the mechanical behavior of bone cement reinforced with alumina particles